Question about GMC Sonoma

1 Answer

Replaced master cylinder blead brakes peddle still goes to the floor front brakes grab rears dont

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 594 Answers

Rear pads worn out or to far from drum to cause friction

Posted on Apr 02, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1999 buick century brake pedal goes to floor-put new master cylinder on and blead both brake lines and master cylinder and pedal still goes to floor


Sounds like you may have a hydraulic leak somewhere. Check the rear wheel cylinders and front brake hoses going to the calipers.

Jan 26, 2012 | 1999 Buick Century

1 Answer

The brake peddle goes to the floor and has no pressue to the peddle? the brakes will still stop the car?


you lost 1/2 master cylinder only front or rears are working or you have air in master cylinder

Aug 07, 2011 | Chevrolet Corsica Cars & Trucks

1 Answer

I had to replace the brake lines in the rear of my car. The brake peddle still goes to the floor. do I need to bled the brakes some more?


Yes, try bleeding the brakes again, you may have to bleed the front brakes too. when the master cylinder goes dry from a broken line sometime air gets into the front lines also. otherwise the master cylinder could be bad when the pedal goes past it normal travel sometime it tears the seals inside and you be unable to build pressure in the master cylinder

Oct 21, 2010 | 1995 Chevrolet Cavalier

1 Answer

Replaced rear calipers and pads now the peddal in soft and goes right to the floor lines have been blead


you must have let air in the system bleed ur beakes all 4 then ur master cylinder you mention calipers so you dont have drums right??bleed your brakes and master if still soft you have blown the seal on the piston in the master

Dec 07, 2009 | 2001 GMC Jimmy

1 Answer

Master Cylinder replacement on 1995 Oldsmobile 88


Start with right rear then left rear,then right front then lft front,Would rebleed at master cylinder 1st.

Jun 18, 2009 | 1995 Oldsmobile Eighty Eight

3 Answers

Brakes are still spongy after changing the pads, one caliper, and master cylinder. bled front brakes.


I just went to Brake Masters this morning and had them replace the Master Cylinder since I was experiencing the pedal very spongy and going to the floor. When they replaced the Master Cylinder and they gave me back the car, the brakes were still spongy and going to the floor. I addressed this to them and they took another look at it, but when I took it for a second time, the brakes were extremely spongy. It was almost like they gave me back my car in worst condition to when I brought it in. Can you help?

May 21, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

I put all new brakes & lines on my 96 gmc pickup.how do i blead?


Its possible your master cylinder went bad, but if it wasnt bad just before you changed brakes i doubt thats it. Check your rear wheel cylinders that push out the pads to make sure their not leaking. Also check for leaking brakelines. Hope this helps.

Mar 22, 2009 | GMC Sierra 1500 Cars & Trucks

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

1 Answer

94 4runner brake pressure.


did you possibly replace brake lines with standard instead of metric lines.The standard lines will fit but you will not get pressure back

Jul 20, 2008 | 1994 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...