Question about Toyota Tacoma

1 Answer

I bled my breaks on a toyota tacoma 4x4 and now my break warning light stays on.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 594 Answers

There is still air in system
i belived ther is a valve that is at the rear of this truck that is link to the frame
the brake lines runs true this valves on the way to the rear
in order to get the brakes to blled properly disconect the valve and move leaver
all the way up attach and re bleed brakes furthes one from master cylinder first
comming closer with each one macking sure no air come out before doing next one
then reconect linkage
the valve also prevents rear wheel lock up when truck is empty and allows
more fluide to go true when truck loaded
in empty mode fluide restricted to rear wheels

Posted on Apr 02, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Break lights stay on,dash lights come on with break peddle..

I'd say you have a short in one of the rear light clusters, or possibly somebody wired a trailer socket wrong. Your dash lights are back-feeding from the rear brake light.

Feb 11, 2015 | 2011 Toyota Tacoma

1 Answer

Adjust emergency brake lever to get brake light to stay off

? If the brake light is on, check your break fluid level first & top it off. If not, check your break lights - one could be out. Last - it's likely your pads are worn down & need new breaks. Have it checked.

Oct 20, 2014 | 2004 Toyota Tacoma

1 Answer

1997 toyota tacoma. No brake lights

First check the break light bulbs if they are good, it is most likely the break light switch locaoed on the break pedal arm its easy to change, and not costly at all, if this does not do it you may have a slort in your break wires this can be hard to trsck down but may be as easy as puting a piece of tape on a bare wire to fix.

Aug 09, 2010 | 1997 Toyota Tacoma

1 Answer

Hi, I have a 2006 Toyota Tacoma and had the rear right leaf spring snap with no weight in it. I was wondering if Toyota had a problem with this in the past.

Its not unusual for a spring to break, usually more apt to break it with bad shocks, as they break on rebound not compression

May 24, 2010 | 2006 Toyota Tacoma

1 Answer

Where are the wires to connect the trailer breke wires to on the back of a 2005 Toyota Tacoma TRD 4x4. I found the connector under the dash for the brake controler and a spot for a 30 amp fuse in the fuse...

check inside the break light compartment.
or if you have a plastic guard where you would mount a ball on your bumper, pull it off and look under there.
on my 4 runner it was under a moulding that held the carpet down where the tailgate closed.

Feb 21, 2010 | 2005 Toyota Tacoma

1 Answer

How do i change my alternator in my 4x4 2001 toyota tacoma? we got the nuts off and all but its not wantin to break loose? anyway someone would be nice enough to help me out? dont have money for takin it...

There are at least two and maybe three bolt connections. Did you get them all? Disconnect the wires before you go any further ... best to disconnect the battery also.

Hope this helps you.

Jan 15, 2010 | 2001 Toyota Tacoma

1 Answer

Diy installing new electric break

yes this can be done by yourself the truck should have come with a pigtail that will plug up under the dash to connect the controller to. if you did not buy the truck new or no longer have that pigtail you can buy them at the dealer they cost approx. $30. all of the newer trucks are prewired for the trailer brakes.

May 19, 2009 | 2006 Toyota Tacoma

1 Answer

Break's light and warning sound on

if you changed master yourself ,& bled out air must have computer hooked up for reset

Jan 05, 2009 | 1993 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides