Question about 1999 Saturn Lw 4dr Wagon

1 Answer

Locked ignition. Can't get car out of park or turn ignition switch. Ignition is locked up.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 41 Answers

You will most likely have to replace key cylinder. remove cowl around steering column, upper & lower, remove plastic cyl around key, you will need a paper clip to remove key cyl. small hole near back of key cyl, install paper clip end pushing down turn key cyl, to run position, jiggle key cyl to remove. auto parts store should have replacement. good luck

Posted on May 29, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
freetek
  • 5568 Answers

SOURCE: A4 steering lock does not engage and car won't turn over

The steering locks don't necessarily engage when the key is removed, I always turn the wheel before exiting to engage it. There are several positions that will allow the pin to lock in but if between these, it may seem that it isn't locked.

Posted on Aug 23, 2008

cartersintn
  • 62 Answers

SOURCE: ignition switch locked up

Try and turn the steering wheel at the same time to take off pressure. If it still wont turn call a locksmith we are usually cheaper than the dealership or if you a mechanically inclined let me know and I will try and tell you how to remove it but it is a lot of work dash will have to come out. Probably what happened is the retainer cover that holds in all the wafers has popped loose very common with gm new ignitions they were better off with the old system hope this helps you

Posted on Sep 09, 2008

MikenAsh
  • 32 Answers

SOURCE: 2002 saturn sl1 ignition switch lock up

the brushes and magnets in the ingnition cyl. are worn and have to replace entire switch.

Posted on Sep 28, 2008

  • 5 Answers

SOURCE: 2002 saturn sl1 ignition switch lock up

Usually this can be temporarily solved with a shot of graphite lubricant into the key hole and moving the steering wheel side to side while turning the key. But, in the end, the ignition cylinder is wearing out and will eventually need replacing.

Posted on Dec 10, 2008

  • 59 Answers

SOURCE: key won't turn the ignition switch in 1999 Saturn SL1

Turn your steering wheel to allow the ignition to fully unlock while turning the key.

Posted on Feb 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My torrent will not start and the key will not come out what do I do


What year is it ? Does yours have floor mounted gear shifter on the console ?
Ignition Lock Cylinder Control Actuator
If the vehicle is equipped with a floor mounted console gear shifter, it has a ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator's purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The column ignition lock system consists of a ignition lock cylinder control actuator , and a Park position switch that is located in the automatic transmission (A/T) shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the Lock position when vehicle transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the Lock position and will not be able to remove the ignition key from the column.

Jun 21, 2016 | Pontiac Torrent Cars & Trucks

1 Answer

Stuck in park will not shift


Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control is a safety device that prevents an inadvertent shift out of PARK when the ignition is ON. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid.


?€¢
The automatic transmission shift lock control switch.


?€¢
The park/neutral position switch.

With the ignition in the ON position, battery positive voltage is supplied to the park/neutral position switch. When the transmission is in the PARK position the contacts in the park/neutral position switch are closed. This allows current to flow through the switch to the automatic transmission shift lock control switch. The circuit continues through the normally-closed switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid, locking the shift linkage in the PARK position. When the driver presses the brake pedal the contacts in the automatic transmission shift lock control switch open, causing the automatic transmission shift lock control solenoid to release. This allows the shift lever to move from the PARK position.
Park Lock Solenoid
The park lock solenoid is a safety device that prevents an inadvertent shift out of PARK when the key is in the OFF position. The key must be in the RUN position to release the park lock solenoid. The system consists of the park lock solenoid. With the ignition in the ON position, voltage is supplied to the park lock solenoid. The park lock solenoid energizes through a permanent ground unlocking the shift lever. With the ignition in the OFF or ACCY position the park lock solenoid de-energizes and locks the shift lever in the park position.
Shift Lever Does Not Move with Brake Pedal Depressed
DEFINITION: Transmission shift lever will not move out of the PARK position with the ignition ON and the brake pedal pressed.

1

Did you perform the Symptoms - Automatic Transmission Shift Lock Control tests and all the necessary inspection?
Go to Step 2
Go to Symptoms - Automatic Transmission Shift Lock Control

2

  1. Turn ON the ignition, with the engine OFF.
  2. Press and hold the brake pedal.
  3. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control switch.
  3. Turn ON the ignition, with the engine OFF.
  4. Press and hold the brake pedal.
  5. Attempt to move the transmission shift lever out of the PARK position.
Does the transmission shift lever move out of the PARK position?
Go to Step 6
Go to Step 4

4

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control solenoid.
  3. Turn ON the ignition, with the engine OFF
  4. Press and hold the brake pedal.
  5. Attempt to move the transmission shift lever out of the PARK position.
Does the transmission shift lever move out of the PARK position?
Go to Step 7
Go to Step 5
Inspect for poor connections at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
Go to Step 9

6

Inspect for poor connections at the harness connector of the automatic transmission shift lock control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
Go to Step 8

7

Repair the short to battery positive voltage in the A/T shift lock control solenoid supply voltage circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 10
--

8

Replace the automatic transmission shift lock control switch. Refer to Stop Lamp Switch Replacement in Lighting Systems.
Did you complete the replacement?

Oct 13, 2015 | 2006 Hummer H2

1 Answer

1999 Volvo S40 cannot remove key


What make vehicle ? Most all vehicles have a safety system .Don't try an force anything you'll break it !
Electronic Park Lock (EPL)/Ignition Lock Cylinder Control Actuator: If the vehicle is equipped with automatic transmission and a floor mounted console gear shift, it has an ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in any position other than PARK and the vehicle may still be moving. The column ignition lock system consists of an ignition lock cylinder control actuator, and a park position switch that is located in the automatic transmission shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column. They also have this on column mounted shifters !

Aug 19, 2015 | Cars & Trucks

1 Answer

The Key FOB is stuck in the ignition. How can I get it to eject?


Most if not all vehicles have a Electronic Park Lock (EPL)/Ignition Lock Cylinder Control Actuator: If the vehicle is equipped with automatic transmission and a floor mounted console gear shift, it has an ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in any position other than PARK and the vehicle may still be moving. The column ignition lock system consists of an ignition lock cylinder control actuator, and a park position switch that is located in the automatic transmission shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column. Or it has
Linear Shift Assembly: If the vehicle is equipped with a column mounted gear shift, it has a linear shift assembly on the steering column. The linear shift assembly has a cable that runs from the linear shift assembly to the ignition lock cylinder case. The purpose of this cable is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The linear shift assembly cable contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.
Your best bet is to take it to a ASE certified repair shop or the dealer ! The fix involves taking the steering column apart an or the floor shifter assembly ! Also electrical test to determine what is the problem !
Your

Jul 04, 2015 | 2008 Volvo S80

1 Answer

The linkage are hooked up but the car still want go into park,a 2000 Taurus


Do you have floor console shifter ?
Shift Interlock System A brake/shifter interlock system consists of the following:
  • ignition switch (11572)
  • brake pedal stoplight switch (13480)
  • brake shift interlock module
  • brake shift interlock solenoid assembly (attached to key interlock assembly)
  • necessary wiring
On floor-shift vehicles, the ignition/shifter interlock cable (3F719):
  • locks the floor shift transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.
  • requires the floor shift transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.

May 04, 2015 | 2000 Ford Taurus

1 Answer

I have a 2003 Chevy blazer xtreme 4.3 v6 automatic transmission and its giving me some issues with the console shifter and ignition system! Every other time I put the blazer in park and try to take the key...


Fixing stuck key in your gmc envoy same as a blazer !
Ignition Lock Cylinder Control Actuator
If the vehicle is equipped with a floor mounted console gear shifter, it has a ignition lock cylinder control actuator system in the steering column as an added safety feature. The ignition lock cylinder control actuators purpose is to prevent the steering wheel from being locked when the transmission is in gear and the vehicle may still be moving. The column ignition lock system consists of a ignition lock cylinder control acutator, and a park position switch that is located in the A/T shift lock control switch. The ignition lock cylinder control acutator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the lock position when vehicle transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.

May 08, 2017 | Cars & Trucks

1 Answer

The ignitioe will not turn out of the off position, the steering column will not lock and transmission shifter depresser button presses but will not move out of park.


SOUND LIKE IGNITION SWITCH KEYLOCK CYLINDER BROKEN. IN WHICH YOU CANT GET CAR OUT OF PARK.THE KEY LOCK CYLINDER BY TURNING THE KEY.IT MOVES A GEAR AND RACK ASSEMBLY THAT IN TURN MOVES THE IGNITION SWITCH ACTUATOR ROD AND PLUNGER TO VARIOUS POSITIONS REQUIRED FOR PERFORMING IGNITION SWITCH FUNCTIONS. IF KEYLOCK BROKEN YOU WONT BEABLE TO TURN IGNITION KEY OR GET CAR OUT OF PARK.

Mar 26, 2011 | 1999 Oldsmobile Alero

1 Answer

How do I change the ignition switch in my 93 plymouth van?


FIRST OF ALL, TURN OFF RADIO,DISCONNECT NEGATIVE BATTERY CABLE. IF EQUIPPED WITH TILT STEERING COLUMN,REMOVE TILT LEVER.CAREFULLY REMOVE THE UPPER AND LOWER STEERING COLUMN COVERS. REMOVE THE 3 TAMPER PROOF TORX IGNITION SWITCH MOUNTING SCREWS USING SNAP ON TOOL TTXR15A2 OR EQUIVALENT. GENTLY PULL THE SWITCH AWAY FROM THE COLUMN AND REMOVE THE 2 ELECTRICAL CONNECTORS FROM THE IGNITION SWITCH. WITH THE KEY IN THE LOCK POSITION, DEPRESS THE KEY CYLINDER RETAINING PIN FLUSH WITH THE KEY CYLINDER SURFACE. ROTATE THE KEY CLOCKWISE TO THE OFF POSITION THE KEY CYLINDER SHOULD NOW BE UNSEATED. ROTATE THE KEY CYLINDER COUNTER CLOCKWISE BACK TO THE LOCK POSITION, AND REMOVE THE LOCK CYLINDER. ( TO INSTALL ) CONNECT THE ELECTRICAL CONNECTORS TO THE IGNITION SWITCH. BE SURE THE CONNECTORS ARE SECURELY LOCKED IN PLACE. MOUNT THE IGNITION SWITCH TO THE COLUMN 3 SCREWS FOR VECHICLES WITH THE TILT STEERING COLUMN THE SHIFTER MUST BE IN THE PARK POSITION AND THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG MUST BE INDEXED BEFORE THE SWITCH IS INSTALLED. PLACE SHIFTER IN THE PARK POSITION. PLACE THE IGNITION SWITCH IN THE LOCK POSITION. THE SWITCH IS IN THE LOCK POSITION WHEN THE STEERING COLUMN LOCK FLAG IS PARALLEL TO THE IGNITION SWITCH TERMINALS. POSITION THE PARK LOCK DOWEL PIN OF THE IGNITION SWITCH SO IT ENGAGES THE STEERING COLUMN PARK LOCK SLIDER LINKAGE. APPLY A LIGHT COATING OF GREASE TO THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG. POSITION THE IGNITION SWITCH AGAINST THE LOCK HOUSING OPENING ON THE STEERING COLUMN. BE SURE THE SWITCH PARK LOCK DOWEL PIN ENTERS THE SLOT IN THE PARK LOCK SLIDER LINKAGE INSTALL THE RETAINING SCREW AND BRACKET. TORQUE THE SCREW TO 26 INCH LBS. INSTALL THE STEERING COLUMN COVERS AND THE TILT LEVER IF REMOVED. WITH THE KEY CYLINDER AND THE IGNITION IN THE LOCK POSITION INSTALL THE KEY CYLINDER INTO THE SWITCH UNTIL IT BOTTOMS. RECONNECT THE NEGATIVE BATTERY CABLE AND THE CHECK THE IGNITION SWITCH FOR PROPER OPERATION OF HALO LIGHT SHIFT LOCK IF EQUIPPED AND COLUMN LOCK.ALSO CHECK FOR PROPER OPERATION OF THE IGNITION SWITCH ACCESSORY, LOCK OFF, RUN AND START FUNCTIONS.

Sep 18, 2010 | 1993 Plymouth Voyager

1 Answer

How do i remove the steering column cover to get at the ignition tumbler on a 1993 dodge dakota


CAUTION Disconnect and isolate the negative (ground) battery cable. This will disable the air bag system. Failure to disconnect the battery could result in accidental deployment and possible personal injury. Allow the system capacitor to discharge for two minutes then begin air bag system component removal. To install:
  1. Engage the electrical connectors to the ignition switch and make sure the switch locking tabs are fully seated.
  2. Before attaching the ignition switch to a tilt steering column, the transmission shifter must be in the PARK position. Also the park lock dowel pin and the column lock flag must be properly indexed before installing the switch as follows:
    1. Place the transmission shifter in the PARK position
    2. Place the ignition switch in the LOCK position. The switch is in the lock position when the column lock flag is parallel to the ignition switch terminals.
    3. Position the ignition switch park lock dowel pin so it will engage the steering column park lock slider linkage.
    4. Apply a light coating of grease to the column lock flag and the park lock dowel pin.
  3. Place the ignition switch against the lock housing opening on the steering column. Ensure that the ignition switch park lock dowel pin enters the slot in the park lock slider linkage in the steering column.
  4. Install the retaining bracket and ignition switch mounting screws, then tighten the screws to 22-30 inch lbs. (3-4 Nm).
  5. If the vehicle is equipped with a tilt steering column, install the tilt lever.
  6. With the key cylinder and the ignition switch in the LOCK position, insert the key cylinder into the ignition switch until it bottoms.
  7. Insert the ignition key into the lock cylinder. While pushing the key cylinder in toward the ignition switch, rotate the ignition key until the end of travel.
  8. Install the retaining screw into the bracket and lock cylinder. Tighten the screw to 22-30 inch lbs. (3-4 Nm).
  9. Install the steering column covers, then the tilt lever, if equipped.
  10. Connect the negative battery cable.
  11. Check for proper operation.


ec3f7ac.jpg

eff2c5f.jpg

72e2667.jpg

7a1362b.jpg

Jul 30, 2010 | 1993 Dodge Dakota

1 Answer

1991 Dodge Spirit ignition problem


The "SPRING-BACK" Action is Originated in the Ignition Switch itself (THE ELECTRICAL SWITCH) I think that is where you should Look. On these models, the ignition lock and ignition switch are removed as an assembly. Refer to IGNITION LOCK .
Disable airbag, refer to Air Bags and Seat Belts/Air Bags (Supplemental Restraint Systems)/Service and Repair . After procedure has been completed, rearm airbag system.

On these models, the ignition lock and ignition switch are removed as an assembly.
  1. Disconnect battery ground cable.
  2. Remove tilt lever.
  3. Remove three Torx column cover attaching screws, then the upper and lower column covers.
  4. Using tamper proof Torx bit tool No. 440-TX20H or equivalent, remove three ignition switch mounting screws.
  5. Carefully pull switch away from column. Release two connector locks on seven terminal wiring connector, then disconnect from ignition switch.
  6. Release connector lock on four terminal connector, then disconnect from ignition switch.
  7. Remove ignition lock from ignition switch as follows:
    1. With key inserted and switch in Lock position, use a small screwdriver to depress ignition lock retaining pin flush with lock cylinder surface.
    2. Rotate key clockwise to Off position. Ignition lock should now be unseated from ignition switch assembly. Do not attempt to remove ignition lock at this time.
    3. With ignition lock in unseated position (lock bezel approximately 1/8 inch above halo light ring), rotate key counterclockwise to Lock position, then remove key.
    4. Remove ignition lock from ignition switch.
  1. Reverse procedure to install, noting the following:
    1. Connect two wiring connectors to ignition switch. Ensure switch locking tabs are fully seated in connectors.
    2. Install ignition switch on steering column.
    3. On column shift models, shift lever must be in P position and park lock dowel pin on ignition switch assembly must engage with column park lock slider linkage.
    4. On all models, verify ignition switch is in Lock position (flag parallel with ignition switch terminals).
    5. Apply a dab of suitable grease to flag and pin, then position park lock link and slider to mid-travel.
    6. Position ignition switch against lock housing face. Ensure pin is inserted into park link contour slot.
    7. Install ignition switch retaining screws and torque to 12-22 lb-in .
    8. With ignition lock and switch in Lock position, insert ignition lock into ignition switch until it bottoms.
    9. Insert key, then while carefully pushing ignition lock toward ignition switch, turn key clockwise to Run position.
    10. Check for proper operation on ignition switch in all positions.

FOR PICTURES EMAIL ME AT MY NICKNAME HERE ON FIXYA @AOL.COM

Feb 12, 2009 | 1991 Dodge Spirit

Not finding what you are looking for?
Cars & Trucks Logo

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...