Question about 1996 GMC Yukon

1 Answer

How do I remove the fuel lines from the electric fuel pump on a 1996 yukon?

Posted by on

  • deh1959jr Apr 02, 2011

    We tried the mallet and the bar to loosen the ring It won't budge?

  • deh1959jr Apr 02, 2011

    You mean the small tab that pushes down on the ring right?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 594 Answers

Need a special fuel disconect tool
clean out conection good (brake clean work well)
put tool over lines and twist back to force into conector
pull lines apart
to reassemble slip in new retainer and push together

Posted on Apr 02, 2011

Testimonial: "Thank you that was very helpful.We went to the auto parts store and bought the tool they came right off."

  • deh1959jr Apr 02, 2011

    Thank you we ended up at the auto parts store to buy the tool.Got hem off now were having a hard time getting the set ring off?

  • DON MAJOR Apr 02, 2011

    yes there sometime corroded badly and they dont come with new pump
    they can be bought ,need to lift on locking tab punch and hammer to turn
    wach out no spark (brass punch better choice) turn anticlockwise to remove

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 voyager fuel pump runs but wont pump


have you checked the fuel pressure regulator on the fuel rail

Jan 27, 2013 | 1996 Plymouth Voyager

1 Answer

Trying to locate the fuse box for the fuel pump under the hood of a 1996 gmc yukon


fuse relay box should have diagram or legend on the cover that will give you fuel pump fuse and relay locations.or look in the owners manual.

May 13, 2011 | 1996 GMC Yukon

1 Answer

1996 accord ex fuel pump replacement


some of these had an access cover under the rear seat(the part you sit on),if you remove this,there should be a cover in the floor board that you remove,and you should see the top of the fuel pump assembly.disconnect the hoses(be careful fuel pressure may still be in the lines).disconnect the electrical wires,remove screws holding unit in gas tank remove pump assembly.transfer necessary components and reverse removal.if there is no access cover then you will have to drop the fuel tank taking care of the wiring and fuel lines.the procedure is the same as above to replace pump.change the fuel filter.

Mar 15, 2011 | 1996 Honda Accord

1 Answer

How do I change a fuel pump on a 2002 yukon


Need to know the size of the engine but this is a picture of what it is....


Posting the rest of the directions for you:


1cf4b2b.gif
Illustrating fuel pump and sending unit sensor (3) on 2000-2004 4.8L, 5.3L, 6.0L Engines

Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
  3. Relieve the fuel system pressure.
  4. Drain the fuel tank.
  5. Remove or disconnect the following:
    • Fuel tank

    WARNING Do not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage tool Joints.

  6. Disconnect the fuel and evaporative emission (EVAP) lines from the fuel tank module.
  • Fuel sender assembly retaining ring using a fuel tank sending unit wrench. Remove the fuel sender assembly and the seal. Discard the seal.
  • Note the position of the fuel strainer on the fuel sender. Support the fuel sender assembly with one hand and grasp the strainer with the other hand. Pull the strainer off the fuel sender. Discard the strainer after inspection. Inspect the strainer. Replace a contaminated strainer and clean the fuel tank.
  • Fuel pump electrical connector
  • Electrical connector retaining clip from the fuel level sensor
  • Sensor electrical connector from under the fuel sender cover
  • Fuel level sensor retaining clip
  • Squeeze the locking tangs and remove the fuel level sensor.
  • Remove the fuel pressure sensor.
  • To install:
    1. Install or connect the following:
      • Fuel pressure sensor
      • Fuel level sensor
      • Sensor retaining clip
      • Electrical connector to the fuel level sensor
      • Electrical connector retaining clip to the fuel level sensor
      • Fuel pump electrical connector

      NOTE Always install a new fuel strainer when replacing the fuel tank fuel pump module.

      • New fuel strainer in the same position as noted during disassembly. Push the strainer on the bottom of the fuel sender until the strainer is fully seated.
      • New seal on the fuel tank

      NOTE The fuel pump strainer must be in a horizontal position when the fuel sender is installed in the tank. When installing the fuel sender assembly, assure that the fuel pump strainer does not block full travel of the float arm.

      • Fuel sender assembly into the fuel tank
      • Fuel sender assembly retaining ring
      • Fuel tank. Install the fuel tank strap attaching bolts. Tighten the bolts to 30 ft. lbs. (40 Nm).
    2. Refill the fuel tank. Install the fuel filler cap. Connect the negative battery cable.
    3. Turn the ignition ON for 2 seconds.
    4. Turn the ignition OFF for 10 seconds.
    5. Turn the ignition ON.
    6. Inspect for fuel leaks.

    Sep 13, 2010 | 2002 GMC Yukon Denali

    1 Answer

    Where is teh fuel filter located on my 99 yukon


    The fuel filter is located under the vehicle on the inside of the frame rail,drivers side.no special tool is required. A 5/8 line wrench to break loose the fuel lines. There is one bolt that holds the bracket to the frame you'll have to remove. Use caution due to fuel pressure on the line.

    Jan 29, 2010 | 1996 GMC Yukon

    2 Answers

    Have a 1995 gmc yukon 2dr i have change the fuel assmble the fuel pump the feed line and return line i have no power to the fuel pump anf help your be gratful ......


    On a NO Power to FUEL Pump Problem One Must ALWAYS Start from the Begining of the THAT CURCIUT, This Being the Fuse , Then The FUEL PUMP Relay , And Then WIRING , and LAST Is The PUMP Itself. Here is Info on the RELAY. rejakwilsoin @ aol.com < is my Email Address if you want More info Feel free to Contact me.

    The Fuel Pump Relay is located in Underhood Fuse Relay Center. The Underhood Fuse Relay Center is located on the LH rear of engine compartment, on fender.


    REMOVE OR DISCONNECT
    1. Protective cover.
    2. Retainer, if installed.
    3. Electrical connector.
    4. Relay by depressing bracket clip at rear of relay, or removing bolts from retaining bracket.
    INSTALL OR CONNECT
    1. Relay.
    2. Electrical connector.
    3. Retainer.
    4. Protective cover.

    Nov 02, 2009 | 1995 GMC Yukon

    2 Answers

    Is the pump located in the fuel tank on a 1997 YUKON GT 2 DOOR


    yes its located in the tak easiest way to replace it is to take bolts out thats holding the bed on and slide bed back and change pump

    Oct 10, 2009 | 1997 GMC Yukon

    1 Answer

    Need to change fuel pump on 2004 GMC Yukon XL Denali and need instructions on how to remove old pump and put in new pump


    well i hope its not full of fuel, remove the filler neck from the car should be 3 bolts by the fuel door, there will also be a ground cable up by thefuel door to remove, next you will have to remove the two straps that hold the fuel tank up slowly lower it as you will have fuel lines and elctrical plugs that need to be detached, the fuel lines have quick fittings, you can buy a tool at auto stores to make removing them easier, un plug the wires., once the tank is out there is a snap ring holding hte fuel pump in the tank. taking a hammer and small drift turn the ring this will release the sending unit, so that you can instull the new one, now reassemble

    Sep 27, 2009 | 2004 GMC Yukon

    1 Answer

    What is the pressure on a fuel pump in a gm vechile?


    The GMC Yukon has the fuel pump located inside the fuel tank. The fuel tank must be removed to gain access to the pump

    Sep 26, 2009 | 1996 GMC Yukon

    2 Answers

    Got a spark, starts sometimes


    fuel pump is bad...u can check the pressure in the line at a local parts store if tey have a guage

    Jul 25, 2009 | 1996 GMC Yukon

    Not finding what you are looking for?
    1996 GMC Yukon Logo

    Related Topics:

    180 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    75005 Answers

    Freddy

    Level 3 Expert

    1311 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...