Question about 2006 Pontiac G6

1 Answer

I went to get an inspection sticker this morning and the gentleman told me that my center high mount stop lamp is out. I replaced the bulbs and they still do not work. I checked the fuses and they are all good. What could be causing them to fail?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 594 Answers

Check for power at socket
if no power check where wire comes from lid to body way be unpluged or brocken
follow the wire until you find power

Posted on Apr 02, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 chevy impala brake light isses switch has been replaced and so have fuses and bulbs still no lights


Do you know how to test using a DVOM - digital volt ohm meter ? Is there B+ voltage going into the brake light switch ? An coming out when the brake pedal is pressed ? What fuse's ? There is only one fuse for the brake lights !
The BRAKE SW fuse in the RH I/P fuse block supplies battery positive voltage to the normally-open stop lamp switch. When you press the brake pedal the switch contacts close and battery positive voltage is supplied to the left and right stop lamp assemblies and to the center high mounted stop lamp (CHMSL). The left and right stop lamp along with the CHMSL are grounded at G302.
Do you know about the right insturment panel fuse box ?
Stop Lamps Inoperative
Step
Action
Yes
No
Schematic Reference: Exterior Lights Schematics
1
Did you perform the Lighting System Diagnostic System Check?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Lighting Systems
2
Press the brake pedal.
Do all of the stop lamps illuminate?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Are all the stop lamps inoperative?
YES - Go to Step 4
NO - Go to Step 7
4
Inspect the BRK SW fuse.
Is the fuse open?
YES - Go to Step 14
NO - Go to Step 5
5
Disconnect the stop lamp switch.
Using a test lamp connected to ground, probe the battery supply voltage circuit of the stop lamp switch connector.
Does the test lamp illuminate?
YES - Go to Step 6
NO - Go to Step 13
6
Install a fused jumper between the battery supply voltage circuit and the stop lamp switch signal circuit of the stop lamp switch connector.
Do the stop lamps illuminate?
YES - Go to Step 12
NO - Go to Step 17
7
Determine if the center high mounted stop lamp is inoperative or the stop/turn lamps are inoperative.
Are the stop/turn lamps inoperative?
YES - Go to Step 8
NO - Go to Step 9
8
Do the turn lamps operate normally?
YES - Go to Step 17
NO - Go to Turn Signal Lamps and/or Indicators Inoperative
9
Disconnect the center high mounted stop lamp.
Using a test lamp connected to ground, probe the stop lamp switch signal circuit of the center high mounted stop lamp at the harness connector.
Press the brake pedal.
Does the test lamp illuminate?
YES - Go to Step 10
NO - Go to Step 15
10
Using a test lamp, probe between the stop lamp switch signal circuit and the ground circuit of the center high mounted stop lamp with a test lamp.
Press the brake pedal.
Does the test lamp illuminate?
Go to Step 11
Go to Step 16
11
Inspect for poor connections at the harness connector of the center high mounted stop lamp. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 20
Go to Step 19
12
Inspect for poor connections at the harness connector of the stop lamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 20
Go to Step 18
13
Repair a open or high resistance in the battery supply voltage circuit of the stop lamp switch. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 20
--
14
Repair a short to ground in one of the following circuits:
• The battery supply voltage circuit of the stop lamp switch
• The stop lamp switch signal circuit of the stop lamp switch
Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 20
--
15
Repair a open or high resistance in the stop lamp switch signal circuit of the center high mounted stop lamp. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 20
--
16
Repair an open or high resistance in the ground circuit of the center high mounted stop lamp. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 20
--
17
Repair an open or high resistance in the stop lamp switch signal circuit of the stop lamp switch. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 20
--
18
Verify the stop lamp switch adjustment. Refer to Stop Lamp Switch Adjustment . If OK, replace the stop lamp switch. Refer to Stop Lamp Switch Replacement .
Did you complete the repair?
Go to Step 20
--
19
Replace the center high mounted stop lamps. Refer to High Mount Stop Lamp Replacement .
Did you complete the repair?
Go to Step 20
--
20
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jun 23, 2017 | Cars & Trucks

1 Answer

How to change brake light bulb on a 2014 fiat 500L


https://www.fiatusa.com/download/pdf/manuals/2014-FIAT-500L-OM-1st.pdf

it's in your owners manual page 358 chapter 7

you need a torx 20 screwdriver or bit

Rear Tail, Stop, Backup And Turn Signal Lamps
1. Open the liftgate.
2. Remove the two screws and remove the tail lamp assembly.
3. Remove the four screws (using a T20 driver) and separate the backplate from the lamp housing.
4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise.
5. Remove the backup lamp bulb by pulling straight out.
6. Replace lamps as required and reinstall lamp.

Center High-Mounted Stop Lamp (CHMSL)
This light is an LED assembly. See your authorized stealership

Mar 30, 2015 | Fiat Cars & Trucks

1 Answer

I was told by a local car shop that in order to fix the High Mount Brake Lamp (brake light is out) that I would need to replace the entire unit. One year ago it cost me $172.03 to replace the entire unit....


check to see if you got two screws if you do all you need is the light bulb if you still have the old one look at it and see if the bulb can be replace without breaking anything i no you mention a year ago

Sep 24, 2012 | 2005 Ford Taurus

1 Answer

Rear turn signal b ulb burned out - How to replace


Rear Turn Signal, Brake and Parking Lights
  1. Remove the tail light assembly screws, then the assembly.
  2. Disconnect the twist lock socket from the lens housing. NOTE: To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1?4 turn, then remove the socket with the bulb; replace the bulb if defective. Fig. 7: Remove the tail light assembly screws, then the assembly - wagon shown 86816223.jpg Fig. 8: Twist the socket counterclockwise to remove from the housing 86816225.jpg Fig. 9: This type of bulb simply can be pulled out of the socket for replacement 86816226.jpg To install:
  3. Attach the socket assemblies to the back of the lamp unit.
  4. Install the lamp assembly to the vehicle with the mounting screws.
License Plate Light
  1. Remove the lens screws.
  2. Once the lens is removed you, can access the bulb and replace if needed. To install:
  3. Install the new bulb, then attach the lens to the body of the vehicle.
Center High Mount Stop Lamp
  1. Remove the screws securing the lamp cover.
  2. Remove the mounting nuts, then unplug the electrical harness to the lamp assembly.
  3. The lamp now should come out. To install:
  4. Position the lamp assembly to the vehicle, then attach the electrical harness to the lamp.
  5. Install the mounting nut, tighten to 62 inch lbs. (7 Nm).
  6. Attach the lamp cover. Fig. 10: Exploded view of the center high mount stop lamp assembly - wagon shown 86816230.gif
    Fig. 11: Light bulb application chart for all models with non-European headlamps 86816237.gif
    Fig. 12: Light bulb application chart for Buicks with European headlamps 86816235.gif
    Fig. 13: Light bulb application chart for Oldsmobiles with European headlamps 86816236.gif
    prev.gif next.gif

Dec 19, 2010 | 1994 Buick Century

1 Answer

Replace a brake light


COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif

Nov 04, 2010 | 1998 Saturn SL

2 Answers

Wondering how to change the third brake light (one located in back window) on a 2006 hyundai sonata


High Mounted Stop Lamp Removal & Installation To Remove:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Disconnect battery negative cable.
  2. Disconnect high mounted stop lamp electrical connector from inside trunk.
  3. Remove package tray.
  4. Replace bulb from package tray.
To Install:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Install package tray.
  2. Connect high mounted stop lamp electrical connector from inside trunk.
  3. Connect battery negative cable.
prev.gif next.gif

Oct 12, 2010 | 2006 Hyundai Sonata

1 Answer

Changing high mounted stop light bulb


HMS Lamp will be mounted in roof or in rear parcel tray.

You have to locate the screws which will be closed/covered by a dummy cap. Remove the cap and unscrew the assembly, you will be able to replace the bulbs

Jun 05, 2010 | 2006 Hyundai Sonata

1 Answer

How do I replace the brake light in the upper back window


Please don't forget to rate! Thank you....
High-Mount Brake Light
  1. Disconnect the negative battery cable.
  2. Pull the center high-mount stop lamp cover to disengage the retaining tabs.
  3. Unfasten the lamp retaining screws.
  4. Remove the sockets using a suitable prybar to release the retaining tabs.
  5. Detach the bulbs from their sockets.
  6. Using a suitable prybar to release the tabs, remove the lamp lens.

9230a99.gif
  1. Installation is the reverse to install. Connect the negative battery cable, then check the lamp for proper operation.

Mar 06, 2010 | 1996 Pontiac Grand Am

2 Answers

I need to replace high 3rd stop light on 1996 pontiac grand am se


  1. Disconnect the negative battery cable.
  2. Pull the center high-mount stop lamp cover to disengage the retaining tabs.
  3. Unfasten the lamp retaining screws.
  4. Remove the sockets using a suitable prybar to release the retaining tabs.
  5. Detach the bulbs from their sockets.
  6. Using a suitable prybar to release the tabs, remove the lamp lens.

8af06eb.gif
View of the center high-mount stop lamp assembly—1995 Grand Am and Achieva shown

7. Installation is the reverse to install. Connect the negative battery cable, then check the lamp for proper operation.

Jan 18, 2010 | 1996 Pontiac Grand Am

1 Answer

How to cchange the third brake light bulb


1992–98 GRAND AM AND ACHIEVA
  1. Disconnect the negative battery cable.
  2. Pull the center high-mount stop lamp cover to disengage the retaining tabs.
  3. Unfasten the lamp retaining screws.
  4. Remove the sockets using a suitable prybar to release the retaining tabs.
  5. Detach the bulbs from their sockets.
  6. Using a suitable prybar to release the tabs, remove the lamp lens. Fig. 14: View of the center high-mount stop lamp assembly — 1995 Grand Am and Achieva shown

Apr 04, 2009 | 1998 Pontiac Grand Am

Not finding what you are looking for?
2006 Pontiac G6 Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...