Question about 2000 Oldsmobile Intrigue

1 Answer

How do you get the pully cover off the water pump for 2000 olds intrigue. removed the 4 bolts and it does not come off.

Posted by on

  • 2 more comments 
  • Darryl Kazemba
    Darryl Kazemba Apr 02, 2011

    What engine do you have? A 4 cylinder or 6 cylinder?

  • Fred Moore Apr 02, 2011

    v6 3.5

  • Fred Moore Apr 02, 2011

    6 cyl

  • Fred Moore Apr 02, 2011

    yes the cover was rusted on, tapped with a hammer and then popped it off with a small pry bar.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,190 Answers

Hello: Something doesn't sound correct. Is the water pump driven by the belt that drives the alternator, a/c compressor and power steering pump? If so the you may have to tap on it with a hammer to break it loose from the engine. Make sure you clean all the old gasket off before installing the replacement.

Posted on Apr 02, 2011

Testimonial: "thanks, yes i tapped with a hammer and then used a pry bar and it popped off, was rusted underneath.thanks "

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the water pump on 2000saturnsl2


Here is that info.
Have a full set of Torx sockets inaddition to the normal ones.

Support the engine.
Remove the air filter box.
Remove the front engine mount.
Pick an order here for the belt and pullies.

What ever will work for you. This is because the serpentine belt will llikely not stop the pullies from spinning. A flat pry bar through two of the bolts on the water and PS pullies while you loosen the third works better. Be careful as the bolt heads round easily.

Remove the water pump pulley.
Remove the power steering pulley.
Remove the serpentine belt.
Remove the lower crank pulley. Outer bolts not the center one
Remove the belt tensioner.
Remove the timing belt covers.
Put a coolant catch pan under the front of the engine.
Remove the water pump.
Clean the sealing surfaces. install the new pump anbd reinsatll the removed parts.
Fill the cooling system and hope that the heater core did not drain. The heater core tends to air lock if it is drained of coolant. This is why the coolant is best drained by removing the water pump and not draining the rad and the entire system.
Run the engine until you have good heat in the car with out having to rev the engine.
Check and top the coolant level as needed

Aug 24, 2012 | 2000 Saturn SL

1 Answer

How to remove water pump on a 98 oldsmobile intrigue


It is very easy! Take off belt by putting a wrench or socket on tensioner pully and rotating it. belt will come right off. You will have to drain coolant. then take out all of the bolts holding the water pump on. you will have to remove the power sterring pump to get to the very back bolt. Make sure you clean old gasket off of the motor and install new gasket with sealer. reassemble in reverse order.
On '98s at least there is an access hole in the p/s pulley that gives you access to that last bolt
I found no access hole except through the power steering which was easier to remove than the PS pully that a pully remover does not have sufficient room. Two bolts top and bottom through the access holes for the PS pump and it is out of the way of the last water pump bolt.


Dec 07, 2011 | 1998 Oldsmobile Intrigue

2 Answers

Trying to find out where the water pump is located on 2000 ford contour


Your water pump is internal. It will be close to the center of the engine and it will have a pully bolted to it. There should be 4 bolts holding the pully on. remove these 4 bolts and the bolts holding the pump on will be exposed. remove those bolts as well(5-7) of them. And your pump will be free. you may have to use a small flathead screwdriver to pry it out. Be sure not to leave any bearings behind when you remove it. clean entire area with puddy knife or razor blade before installing new one. Install is reverse. Hope this helps.

Jul 23, 2011 | 2000 Ford Contour

1 Answer

How to locate and change water pump on 2000 buick lesabre, 6 cylinder engine


I assume you have a 3800 V6 motor in that model car. When standing with the hood open on the passenger side of the car, the water pump is located in the center of the engine. The pulley will have four small (8mm) bolts. To remove: Loosen the 4 bolts on water pump pulley.
Use 13mm socket wrench on tensioner pully to rotate and pull tension off of serpentine drive belt. Take belt off of tensioner and water pump pulleys, bend back out of the way. Finish removing water pump pulley bolts and remove pully. Remove water pump bolts (there are several of 2 different sizes, 10mm and 13mm) . Remove old pump by prying gently around the pump rim to break the gasket's seal, or tap shaft with a rubber hammer. Remove all signs of gasket material on engine mating surface with a scraper and then some fine sandpaper (1000 grit wet/dry) or steel wool. Use high-tack sealant to mate gasket to new water pump, allow to set to a few minutes. Use high-tack again on engine mating surface, allow to set a few minutes, then put water pump to engine using the small bolts tightening them finger tight. Put a small amount of black RTV sealant on larger, long bolt ends about 1/2 " of threads covered. Insert longer/larger bolts and tighten finger tight. Tighten all bolts to firm hand tight using a criss-cross pattern starting in the center top to bottom, then side to side.Do not overtighten, as damage to your new pump or striping thread holes out will result. Allow assembly to set 1/2 hour for sealants to cure. Install pump pulley. Install drive belt. Refill coolant level. Start engine, allow to warm up and check for leaks. Done! :)
Mike

Jun 11, 2011 | 2000 Buick LeSabre

2 Answers

I need 2 replace a water pump 4 my 2000 Oldsmobile Intrigue what is the OME part #?


who cares what the part number is - I would highly recommend buying the water pump on eBay - you can find it by typing in the year, make and water pump - I am an ASE tech and I am constantly amazed at how much cheaper the same parts are on eBay instead of a parts store - hope this helps

Mar 23, 2011 | 2000 Oldsmobile Intrigue

1 Answer

WHERE IS THE WATER PUMP LOCATED...2003 ELANTRA


hi from uk fortunately the water pump on your car is not driven by cambelt ! the pump is driven by serp belt the pumps location is = if you look at front of engine view from front wing as you look down front you will see a large pully on left of cambelt covers and this is the water pump access to pump is best by supporting car and removing wheel and then the under wing cover that is secured by screws some advice for you if you intend renewing pump the pump pully is secured by 4 bolts use a 10 mm cranked ring spanner or socket loosen these bolts before you remove the drivebelt as belt holds pully and helps to prevent pully turning as you try to loosen these bolts hope this helps ?

Jan 26, 2010 | Hyundai Motor 2003 Elantra

2 Answers

Need to replace water pump on a1997 chevy lumina 3.1L V6 need insructions


3.1L And 3.4L (VIN E) Engines
  1. Disconnect the negative battery cable.
  2. Partially drain the cooling system into a suitable container.
  3. Remove the drive belt guard.
  4. Loosen the water pump pulley bolts before removing the drive belt. This should help keep the pulley from turning as the bolts are loosened.
  5. Remove the drive belt. Please see Section 1.
  6. Remove the water pump pulley bolts and remove the pulley.
  7. Remove the water pump bolts and separate the pump from the engine front cover.
To install:

b604dca.gif
Exploded view of the water pump and front cover arrangement—3.1L and 3.4L (VIN E) engines


  1. Clean all parts well. Use care when scraping gasket material from the front cover and the pump. Do not gouge aluminum parts. Clean the bolt threads well. The torque specification is low and if the bolt threads are dirty, an accurate torque is not possible and leaks are likely to develop.
  2. Using a new gasket, install the water pump to the front cover. Install the cleaned and lightly lubricated water pump bolts. Torque to 89 inch lbs. (10 Nm).
  3. Install the water pump pulley and bolts and torque to 18 ft. lbs. (25 Nm).
  4. Install the remaining components in the reverse order of the removal process. When refilling the cooling system, use the proper mix of DEX-COOL® and water. Check for leaks.

Oct 13, 2009 | 1997 Chevrolet Lumina

1 Answer

Do you have to remove the yoke to change the water pump and if so is the bolt l. or rt. hand threaded


There is NO yoke. There is, however, a water pump pully attached with 4 10mm bolts which must be removed in order to access the water pump bolts (12mm). Bolts are threaded right hand (clockwise to tighten, and counter-clockwise to loosen).

Oct 05, 2009 | 2000 Hyundai Elantra

1 Answer

Having trouble getting water pump out of 94 lantra 1.8 lt


1. Remove the alternator & power steering pump drive belts.
2. Remove four (4) 10mm bolts holding the water pump pullys & remove the pullys.
3. Drain the Radiator (save coolant if intend to reuse).
4. Loosen & remove AC compressor belt.
5. Remove crankshaft pully (22mm bolt).
6. Remove lower timing belt cover (10 mm bolts) to access water pump bolts.
7. Remove the water pump (12mm bolts)
(1) Remove the 2 bolts, then remove the alternator brace (A). (2) Remove the water pump (B) and gasket.
dbb00ee.jpg ef0cc15.jpg 8. Clean mating surface on engine & install new gasket & pump - reassemble. Refill w/50-50 coolant.

Mar 21, 2009 | 2004 Hyundai Elantra

2 Answers

On 98 intrigue water pump removal how do i clear the ps pully


Im not sure what engine you have since this information was not provided. But the Power Steering Pump pulley usually has some 'holes' on the pulley in which you can get a wrench through to loosen and remove the bolt.

Dec 29, 2008 | 1998 Oldsmobile Intrigue

Not finding what you are looking for?
2000 Oldsmobile Intrigue Logo

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...