Question about 2002 Chevrolet Silverado 2500HD

Open Question

Ineed to replace rear wheel bearing what do I need to know

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

leetamara
  • 702 Answers

SOURCE: Wheel Bearing

Yes, it's time for wheel bearing replacement. It seems a little premature to me though.

Posted on Jul 03, 2008

mrgreenz
  • 962 Answers

SOURCE: (How do I replace rear bearings) chevy sliverado RWD

Check to see if the drum is hotter than normal. If the bearings are bad, you have to lift the truck and remove the axle. Remove the wheel drum until you get to the axle. They to remove the axle, you have to open the rear end Spider gear ***** at the middle. They have a half moon wedge or a clip you have to remove. They you pull out the axle.Replace the bearing grease it and seal it. Then put it back in the reverse order. Sounds simple but it is not that simple. Takes work

Posted on Jan 11, 2009

  • 2 Answers

SOURCE: what torque for rear wheel bearing Ford Focus 2000

Can only find out that the hub needs to be tightened to
235 nm Dunno if this helps

Posted on Jan 27, 2009

  • 4369 Answers

SOURCE: rear wheel bearing

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Posted on Apr 10, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a rear wheel bearing on suzuki xl-7


is there any special tools you need to change the rear wheel bearing

May 08, 2012 | 2004 Suzuki Vitara

1 Answer

I need to know how to change the rear wheel bearings on my 1997 Dodge Grand Caravan.


Hello pixxi 29: My name is Roger and I will help you. To replace the rear bears would be impossable to do. THis is a sealed unit you must replace the entire hub and bearing unit. To do this raise and support the van. Remove the rear tire and wheel. Remove the brake drum to expose the hub unit. Remove the 4 bolt that hold the hub onto the backing plate. Reinstall with the new hub and bearing and tighten the bolts. Make sue they are tight replace the brake drum and tire and wheel. Should you need further help please just ask. Please rate the answer you received. hank You for using Fix Ya. Roger

Sep 23, 2010 | Dodge Grand Caravan Cars & Trucks

1 Answer

How to replace rear wheel bearings on a1992 chev. 1500. Ineed step by step instrucions.


Pull dif. cover off. Remove small bolt holding spider gear pin in. Remove pin. Push one axle in remove "C" clip. Push other axle in remove "C" clip. Pull axles out. Pry seal out. Using slide hammer pull axle bearing out..

Need some good testimonials .

Sep 22, 2010 | 1992 Chevrolet K1500

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

1 Answer

I get a vibration as im driving possible from the rear wheel


a) Wheel Balance.
b) Wheel Alignment
c) Wheel Bearing.
My best guess is a wheel bearing needing replacement. If there is only noise, then MAYBE repacking of bearings. However with vibrations, the wheel bearing(s) need to be replaced. Make sure you replace both the bearing and races as a set.
Let me know if this helped or if you need additional help.

Dec 09, 2009 | 1992 Plymouth Acclaim

2 Answers

Have a roaring noise coming from the rear


sounds like a wheel bearing to this mechanic, if you have near 100,000 miles that is almost certainly the problem.

Aug 31, 2009 | 2003 Saturn VUE

1 Answer

Need instruction manual/schematics for replacing 2005 kia rio driver side rear wheel bearing. i've got the wheel/hub/bearing off, not the inside ring to the bearing. i need to know how to replace it .


clean all the grease if there is any out of the hub, turn the hub over and using a drift and hammer strike the shell from the back edge working around the shell as you go, should not take too much to remove it but you will need a bit more than a tap with the hammer.
Hope this has helped you

May 22, 2009 | 2003 Kia Rio

1 Answer

Replace left rear axle seal 1999 ford explorer


Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the differential housing cover (4033).
    1. Loosen the bolts and drain the lubricant from the rear axle housing (4010).
    1. Remove the bolts.
    1. Remove the differential housing cover.
Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Turning the differential case (4204) or an axle shaft (4234) with the differential pinion shaft (4211) removed will cause the differential pinion gears (4215) to fall out of the assembly and damage the components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  2. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the U-washer groove.
  3. Remove the U-washer (4N237).
  4. Push the axle shaft inboard.
  5. Remove the U-washer.
Reinstall the differential pinion shaft.
  1. Install the differential pinion shaft.
  2. Install the differential pinion shaft lock bolt finger-tight.
  3. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal (1177).
    Remove the axle shaft.
-----------------------------------------------------------------------------------------------------------------
Seal Removal
  1. Remove the axle shaft (4334). For additional information, refer to Axle Shaft in this section.
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the wheel bearing oil seal (1177) by itself. Always remove the rear wheel bearing (1225) and the inner wheel bearing oil seal at the same time.
    NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged with foreign material.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal together.
6c7eb46.gif Installation
  1. Lubricate the new rear wheel bearing.
    • For 4.0L SOHC and 4.0L EI with limited slip rear axles and 5.0L vehicles, use SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A.
    • For 4.0L SOHC and 4.0L EI with conventional rear axles, use SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Using the special tools, install the rear wheel bearing.

ece7d89.gif
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the wheel bearing oil seal.
c21e27d.gif
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

Feb 22, 2009 | 1999 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...