Question about 2000 Hyundai Accent

1 Answer

How to replace the front wheel bearing on a Hyundai Accent 2000?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 128 Answers

Wheel bearing for all car makes available here. You can replace your wheel bearing here. http://www.buyautoparts.com/part/replacement-wheel-bearing/

Posted on Apr 28, 2011

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: front wheel bearings

your going to need a press to press the old bearings out and the new ones in i recomend you take it to a shop if you dont have one

Posted on Feb 06, 2009

  • 1 Answer

SOURCE: Trying to get to the wheel bearings on the front

remove the whole assenbly strut an all and you need to place it in a vice...use a device the same size as the berring housing, after you remove the snap ring and hammer out the berring....but you also have to hammer off the rotor off...easiest way to get of a seized rotor is to apply some heat around the berring area and then add cold water...one or two bangs will get the rotor off...or use muscle...

Posted on Aug 28, 2009

  • 4793 Answers

SOURCE: i am replacing my front wheel bearings on my

wheel bearings are the same all over,no problems...do the nut up tight then back off 1/8th turn...

Posted on Jun 19, 2010

michigan man
  • 3533 Answers

SOURCE: Rear wheel bearings on Hyundai Accent

no i do not believe they are press in there are held in by a seal try www.autozone.com to see if they have your car listed if they do you will be able to get a diagram showing you how they come a part.

Posted on Apr 24, 2009

  • 65 Answers

SOURCE: 2000 hyundai accent

Their shop website says below but you can call the service department. usually you want to tighten it just until it starts to not rotate freely then back off just a little bit. It should spin freely.

Hub bearing starting torque [Limit] : 1.8 Nm (18 kgf·cm, 1.33 lbf·ft) or less

Posted on Sep 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace front wheel bearing in a 2008 hyundai accent?


Hi there, I think from memory the whole hub assembly comes with new bearings when you replace it, it's a easy change, remove wheel, remove the brake calliper, remove the front axel nut and the hub should come off, hope this helps, it's a easy change

May 19, 2014 | 2006 Hyundai Accent

1 Answer

How can I replace front wheel bearing on my 2008 hyundai accent myself?


SKF number FW178. (or equivalent) https://www.youtube.com/watch?v=l0LCkycUcqM DON'T leave just a jack holding the car up! It's actually on stands you can't see in this video. Soft ground makes cars fall over and crush people.

May 17, 2014 | 2008 Hyundai Accent

1 Answer

How much to replace front wheel bearings in a 1999 hyundai accent?


Front wheel bearing Hyundai 1998/1999 :

1. Timken: Pn. TMSET41
2. Auto 7 : Pn. AU71000059 or equal

with price about $ 50 max. ( parts only)

Aug 13, 2010 | Hyundai Motor 1998 Accent

1 Answer

Tie rod end replacement and wheel bearing replacement instructions. Midas service man performing an oil change indicated it was important that the right frong tie rod end and wheel bearing be replaced on...


best advice is a garage with the right equipment ,ever see a splinter in a eye from hammering a bearing out ,not very nice ,even worse sitting in emergency for 3 hrs waiting to see a doctor

Jun 27, 2010 | 2000 Hyundai Accent

1 Answer

Rear wheel bearings on Hyundai Accent


no i do not believe they are press in there are held in by a seal try www.autozone.com to see if they have your car listed if they do you will be able to get a diagram showing you how they come a part.

Apr 24, 2009 | Hyundai Motor 1998 Accent

1 Answer

Front wheel bearings


your going to need a press to press the old bearings out and the new ones in i recomend you take it to a shop if you dont have one

Feb 02, 2009 | 2000 Hyundai Accent

1 Answer

Bearing trouble


Ouch, get your wheel bearings checked. I had a 97 Hyundai and in the 3 years I had it, the front bearings had to be replaced twice and the rear once once.

Sep 28, 2008 | 1997 Hyundai Accent

1 Answer

2000 hyundai accent


Their shop website says below but you can call the service department. usually you want to tighten it just until it starts to not rotate freely then back off just a little bit. It should spin freely.

Hub bearing starting torque [Limit] : 1.8 Nm (18 kgf·cm, 1.33 lbf·ft) or less

Jul 29, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
2000 Hyundai Accent Logo

2,913 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...