Question about 1998 Jeep Wrangler

1 Answer

Someone ripped the crankshaft senser wire out of the senser. we didn't know what the wire went to, all we knew is that my 2000 jeep wrangler would not start. my friend touched the wire to the hot and has done something to the vehicle. i did replace the crankshaft senser but still am not getting any fire at all. i have checked the fuses and i have checked the relays. What should I do next?

Posted by on

  • Anonymous Mar 15, 2014

    2008 wrangler 02 senser wiring ripped out



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Top drivers side of transm.bell housing

Posted on Jun 13, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

95 jeep wrangler not getting fire

So many of them things could have been checked to see if they was bad or needed to have been replaced. I see this a lot when someone goes to guessing on things and they can end up having a LOT of money invested and still not running.
My first guess since you've replaced all of them things is either you may have a ground issue or a bad PCM.
I would start by checking that you are getting power to everything that you are supposed to be getting power.

Then, I would check that you are getting grounds to everything too! You must have both in order for it all to work! If you are getting both and if you know how to check for both at all places, then I would eliminate the PCM.

If it turns out to be the PCM, try checking eBay.
Hope this helps.

Dec 12, 2017 | 1995 Jeep Wrangler

1 Answer

Speedometer not working on my 1995 wrangler. I changed the speed sensor, did not solve the problem.

On my 95 jeep wrangler, the vehicle speed sensor is on the end of the transfer case. I replaced mine and it still didn\'t work. So I put new butt connectors on the wires and that was why my speedometer wasn\'t working ... so you need to be careful when crimping the wires without crimping the bells at the ends of the connectors.

Dec 24, 2010 | 1995 Jeep Wrangler

1 Answer

2000 jeep wrangler 4.0l no power to fuel pump

Check your relays. Find where you've got power and where it stops... you'll find the problem. Good Luck. "It's always something simple."

Dec 07, 2009 | 2000 Jeep Wrangler

1 Answer

Our brake lights keep going out, the Stop LPS Fuse keeps popping. My husband checked wires, nothing looked wrong. He replaced the brake lamp switch and fuse still popped. Now he's checking actual tail...

check to see if someone has installed a tow hitch on the rear,they would have spliced in the wiring in the rear of vehicle,thats where i find alot of corroded wire that were poorly taped.

Nov 24, 2009 | 2000 Jeep Wrangler

2 Answers

I blew the gearbox /transfer case/tailshaft in my jeep 2000 model wrangler sport. I have replaced all of the above but I also ripped apart all the wiring underneath I need some sort of electrical manual so...

Most wires are color coded,,, and if they are still intact (just cut into) you should be able to put them back together by just matching the wires according to the colors. No manual should be necessary to accomplish this?

Oct 10, 2009 | 2000 Jeep Wrangler

1 Answer

1999 jeep wrangler guages went crazy

Put a volt meter on the battery itself and take a reading when it is doing that. If charge rate is over 14v the alternator may be working but the output is not being cut down to "useful voltage" You may have a regulator problem.

Jun 23, 2009 | 1999 Jeep Wrangler

1 Answer

My 1997 Jeep Wrangler Sport wont start!!

yea i would try replacing the pmc valve if its not your crankshaft

May 14, 2009 | 1997 Jeep Wrangler

1 Answer

Ignition system is out

check crankshaft sensor (left side of bellhousing underneath) DO not buy one first, test it with an ohmeter (specs in any manual) if out of range then change it. Also suspect will be ignition module (if you have one, it's next to the coil. After checking these out, if no results, check cam sensor Inside distributor. That's enough to confuse you for awhile.
Good luck

Mar 02, 2009 | 1995 Jeep Wrangler

1 Answer

Don't know if engine is seized how can i tell

disconnect the battery and put a wrench on the center bolt of the crankshaft pulley, see if you can move it.

Jan 23, 2009 | 1995 Jeep Wrangler

Not finding what you are looking for?
1998 Jeep Wrangler Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides