Question about 1995 Honda Passport

1 Answer

CLUTCH REPLACED CLUTCH BUT DONT KNOW TO BLEED ANY OF THE LINES IN A 95 HONDA PASSPORT

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 91 Answers

That clutch can bled by using the bleed screw located just aft of the engine/tranny union where the clutch line enters the tranny. Loosen the screw and also loosen the cap on the hydraulic clutch reservoir. watch for fluid trickling out from the transmission end of the line, when this is confirmed, than close the bleed screw, cover the resevoir, make sure theres enough fluid, and pump on the clutch pedal a few times. You can repeat these steps again if necessary to remove and extra air trapped in the system.

Posted on Aug 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How many quarts of transmission fluid for a 95 honda passport?


Generally speaking, we start with 4 quarts when the filter is changed and add until the stick shows it to be full.
The total capacity would include draining the torque converter which is seldom done.
Does it show overfull on the stick ?

Feb 18, 2013 | 1995 Honda Passport

1 Answer

Manual transmission will not disenage the clutch?


If you have a hydraulic clutch (slave cylinder to clutch fork) try bleeding it.
if it leaks you will have to replace it> If it is a manual clutch fork and the clutch starts to grab right off the floor the clutch is woen and will have to be replaced. You might also check the clutch rod for adjustment > in either case make sure the clutch rod is seated in the clutch fork.

Mar 24, 2012 | 1996 Honda Passport

1 Answer

What is the gear ratio of a 95 honda passport v6 rear differential


no idea to be honest ,dont have a manual but if jack up one wheel and then turn prop you can then count it ,wont work with two wheels off the floor though

Apr 04, 2011 | 1995 Honda Passport

1 Answer

Bleeding clutch in 1994 honda passport


IT IS JUST LIKE BLEEDING A BRAKE SYSTEM HAVE A HELPER GET IN AND PUMP THE CLUTCH PEDAL AND THEN HOLD IT DOWN AND OPEN THE BLEEDER ON THE SLAVE CYLINDER KEEP DOING THIS 4-5 TIMES AND YOU SHOULD HAVE A PEDAL IF NOT THERE IS ANOTHER PROBLEM MAKE SURE TO KEEP THE CLUTCH MASTER FULL

Oct 16, 2010 | 1994 Honda Passport

3 Answers

How do I adjust clutch on 1995 Honda Passport?


You don't. They are hydraulic. Check the slave cylinder for leaks or if you need to fill the reservoir. You might need to bleed the system if it continues and you find no leaks.

Apr 15, 2009 | 1995 Honda Passport

1 Answer

Need to know how to bleed clutch of 1995 honda passport. Do- it - yourself instructions. The clutch pedal is pushed down with no resistance at all. Once pushed down i can start the car but the clutch will...


Fill the clutch reservoir with new brake fluid and kneel down beside the car, reach in with your hand and pump the clutch pedal up and down until it starts to return on it's own. Check the reservoir level, hop in the car and pump the pedal about twenty times with you foot, the clutch will self bleed and you'll be able to shift. If there is a leak somewhere, this problem will reoccur until the cause of the leak is fixed.

Mar 30, 2009 | 1995 Honda Passport

1 Answer

Bleeding the clutch line


It sounds like you have air in the system. Either they did not bleed it correctly or you have a leak in the system.
If you paid someone to fix your car, have it towed back to the garage and bled correctly or leak fixed. If a friend installed your parts, find a new friend. Just kidding.

Dec 31, 2008 | 1995 Honda Passport

1 Answer

Passport not firing


Open the fuel line near the injector pump by loosening the line nut preferably with a hex line wrench or find a bleed port on the injector and loosen it. Remove the ignition coil wire to to avoid a fire. Once some place is open for the gas to flow and flush the fuel line, crank on the engine for a short time til all the air is flushed from the fuel line, then tighten the line or bleed port nut to stop the leaks. Replace the coil wire and start the engine normally. Good luck and happy new year.

Dec 12, 2008 | 1995 Honda Passport

Not finding what you are looking for?
1995 Honda Passport Logo

270 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...