Question about 1994 Chevrolet C1500

1 Answer

My 1994 silverado 5.7 auto 4x4 started slipping after shop had the driveshaft out to change u joints. found it was 2 qts low. added fluid. adrives good when cold and slips when it is warmed up. Am I i trouble here or could it be something else?

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 3 Answers

Try checking fluid level constently and maby check the pressure my 2000 silverado did that but it was cuz i put a new trani in and one of the trani lines popped off the fitting so u gota make sure u have no leaks first off

Posted on Apr 02, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Carrier baring


1) Flat level surface, chock the front tires.

2) Jack the rear up just until the tires clear.
USE jack stands. (DO NOT EVER just depend on a jack)

3) Remove the rear bolts holding the rear U-joint in.
Carefully use a tool to pry one of the U-joint cups, until the U-joint comes loose. DO NOT drop the cups off. Keep one hand wrapped around the cups as you pry the U-joint loose.

When U-joint is removed, suggest use black plastic electrical tape, and tape across the two cups, so they do not drop off.

[GOOD time to see if they are dry, and the U-joint is in good condition. DO NOT loose needle bearings ]

4) Remove the bolts that hold the Carrier Bearing Support to frame.
(Put the nuts back on a few threads of the bolts, after putting them back through the holes, in the Carrier Bearing Support strap. This way you won\'t lose them)

Lay the Support strap, and rubber aside.

5) Slide the driveshaft out of the back of the tranny. (Transmission)
It would be a real good idea to go to an auto parts store first, and rent a plug tool for the back of the tranny, once you remove the driveshaft. Keeps the tranny fluid from leaking out. Manual or automatic. (It is plastic, and a cheap rental)

The rear half-driveshaft slips out of the front one.
BEFORE removing make a mark on the front half-driveshaft, and a matching mark on the rear half-driveshaft. The driveshaft is a Balanced unit. Should be put back together the same way, it was taken apart.

Take the driveshaft with the carrier bearing on it to a shop, so they can press the old one off, and the new one on.

Reverse your steps.

(Owner of 1994 GMC Sonoma 2-wheel drive, extended cab. Civilian mechanic on Army base. Work on ALL wheeled vehicles, and track up to, but not including, Abrams M1A2 tank )

Regards,
joecoolvette

Dec 17, 2012 | 1991 GMC Sonoma

1 Answer

Transmission slipping after changing cracked pan


check the filter for cracks if nothing there look for damage to steel tubes that also run near the filter.

Jul 31, 2010 | 2002 Pontiac Grand Am

1 Answer

How do i replace a driveshaft for a 1997 lincon cotanental


I searched under 1997 lincoln continental and found this: Driveshaft and U-Joints
REMOVAL & INSTALLATION Town Car and Mark VII-VIII Fig. 1: The bolts retaining the rear driveshaft yoke-to-differential flange require a 12mm, 12 point wrench or socket to loosen them 91197p12.jpg
Fig. 2: Remove the bolts retaining the rear driveshaft yoke-to-differential flange 91197p11.jpg
Fig. 3: Separate the driveshaft from the axle flange and . . . 91197p13.jpg
Fig. 4: . . . disengage the driveshaft from the transmission output shaft 91197p14.jpg
Fig. 5: Insert a plug onto the splines of the transmission output shaft to prevent fluid from leaking out 91197p15.jpg
  1. Raise and safely support the vehicle.
  2. Mark the position of the driveshaft yoke on the axle companion flange so they can be reassembled in the same way to maintain balance.
  3. Remove the flange bolts and disconnect the driveshaft from the axle companion flange.
  4. Allow the rear of the driveshaft to drop down slightly.
  5. Pull the driveshaft and slip yoke rearward until the yoke just clears the transmission extension housing seal. Mark the position of the slip yoke in relation to the transmission output shaft, then remove the driveshaft.
  6. Plug the transmission to prevent fluid leakage. To install:
  7. Lubricate the yoke splines with suitable grease.
  8. Remove the plug from the transmission and inspect the extension housing seal; replace if necessary.
  9. Align the slip yoke and output shaft with the marks made at removal and install the yoke into the transmission extension housing. Be careful not to bottom the slip yoke hard against the transmission seal.
  10. Rotate the axle flange, as necessary, to align the marks made during removal.
  11. Install the driveshaft yoke to the axle flange. Install the bolts and tighten to 71–95 ft. lbs. (95–130 Nm).
  12. Lower the vehicle.
prev.gif next.gif

Jul 05, 2010 | 1997 Lincoln Continental

1 Answer

Sidekick tranny slips


try changeing the oil and transmission filter

Apr 05, 2010 | 1994 Suzuki Sidekick

1 Answer

1994 chevrolet Silverado 4x4 with the transmission slipping


It will work but you will have to modify the crossmember and driveshaft and the computer. The 4l60e is an easy trans to recondition

Feb 23, 2010 | 1994 Chevrolet C1500

1 Answer

How much oil does a 80 series petrol auto take in a change?


5 to 6 qts general rule start with 4.5 and check adding as needed

Jan 15, 2010 | 1994 Toyota Land Cruiser

2 Answers

Part names


cardan centering bearing
point bolts needed to be removed that connects D.S.to transfercase

May 22, 2009 | 2001 Ford Excursion

3 Answers

How much transmission fluid does a 1999 subaru Legacy BH need


automatic trans 2.2liter engine- 1990-1993/ 8.8 qts.
1994-on/ 8.4 qts
2.5 liter engines 10 qts. all years

manual trans 2.2 liter 2wd 1990-1994 3.5 qts
1995 2wd 3.7 qts

4wd 1990-1994 4.2 qts
4wd 1995 on 3.7 qts2.5 liter aall years 3.7 qts.

Jan 25, 2009 | 1999 Subaru Legacy

2 Answers

2000 Silverado L/T Z71 4X4 Lubrication Diagram


Lube points should be: All moving joints in suspension. Ball joints, idler arm, tie rod ends etc. On 4X4's, all universal joints on drive axles (excluding C/V joints... just inspect boots) All slip-joints and "u" joints on driveshafts. Many of these items may not have zirk fittings on them from the factory. If the component has a plug installed, it should be removed & replaced with a fitting. If there is no place for a fitting, when the item wears out, the replacement will have a fitting.

Sep 13, 2008 | 2000 Chevrolet Silverado

Not finding what you are looking for?
1994 Chevrolet C1500 Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...