Question about 1995 Oldsmobile Cutlass Ciera

1 Answer

Windshield washer fuild will not come out passenger side. Does the driver side. How do I remove the left front cover speaker cover.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Legend:

    An expert who has written 200 answers of more than 400 characters.

  • Expert
  • 332 Answers

I know an easy fix if you can get access to the rubber tube that is the opposite end of where the fluid comes out of. Just blow into the rubber tube as hard as you can. When the obstruction blows out of the tip of where the fluid sprays on your windshield then hook the rubber tube up and test your washers again. Ive done this many times and its always worked for me.

I hope this helps you out.

Posted on Apr 01, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which fuse controls front windshield wiper pump


Do the wipers work ? Fuse for wipers is same as washer pump .
Principles of Operation
The wiper motors receive inputs from the following:
  • Multi-function switch
  • Powertrain control module (PCM)
  • Ignition switch
  • Smart junction box (SJB)
The following components are integrated in the wiper motors:
  • Windshield wiper motor module
  • High/low speed relay
  • Run/park relay
  • Washer pump relay
  • Park sense (Hall-effect sensor)
Washer System
The windshield washer and the rear window washer are activated by the internal wiper motor modules when it receives a ground from the multi-function switch between the washer inputs. Depending on the correct ground, the internal wiper motor modules activate either the windshield washer or rear window washer relays (internal) by grounding the respective relay coil. When either module is activated, it connects voltage to the washer pump while the deactivated module provides ground to the washer pump. In this manner, voltage polarity is reversible to achieve directional change of the washer pump and washer fluid.
  • The washer pump is inoperative
  • Circuitry
  • Washer pump
  • Multi-function switch
  • Windshield wiper motor
  • Rear window wiper motor
  • Go To Pinpoint Test I .
Does your expedition have programmable/recall memory option for seats an mirrors ?
Driver Seat Module
The power driver seat and power exterior mirrors are controlled by the driver seat module (DSM) only when the vehicle is equipped with the programmable/recall memory option.
On the Expedition Limited, the power fold exterior mirror option is controlled by the DSM. Before running a self-test or retrieving codes, the power fold switch must be inactive for at least 30 seconds.
This is a complex vehicle , electronics , control modules an serial data communication networks. You mite be better off taking it to the dealer or some other repair shop . There could be DTC'S - diagnostic trouble codes stored in the SJB - body control module !
B1667 Mirror Driver Up/Down Motor Stalled Go To Pinpoint Test D . B1668 Mirror Driver Right/Left Motor Stalled Go To Pinpoint Test D . B1669 Mirror Passenger Up/Down Motor Stalled Go To Pinpoint Test D . B1670 Mirror Passenger Right/Left Motor Stalled Go To Pinpoint Test D . B1735 Mirror Driver Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1739 Mirror Driver Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B1743 Mirror Passenger Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1747 Mirror Passenger Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B2312 Mirror Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2314 Mirror Passenger Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2316 Mirror Passenger Vertical Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2318 Mirror Passenger Vertical Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2320 Mirror Driver Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2322 Mirror Driver Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . Normal Operation During normal operation, when the front wiper wash is selected, the windshield wiper motor provides power to the washer pump through circuit CRW14 (BU/WH) and ground is provided to the washer pump through circuit CRW12 (GY/OG) and the rear wiper motor. If rear wiper wash is selected, the rear wiper motor provides power to the washer pump through circuit CRW12 (GY/OG) and ground is provided to the washer pump through circuit CRW14 (BU/WH) and the windshield wiper motor.
    Possible Causes
  • Multi-function switch
  • Open in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN), CRW20 (GY/YE), SBB49 (RD) or GD149 (BK/GY)
  • Short to ground in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN) or CRW20 (GY/YE)
  • Washer pump
  • Windshield wiper motor
  • Rear wiper motor
    This is

Feb 02, 2016 | 2010 Ford Expedition

7 Answers

How do I add wiper fluid to my car?


Hello. Usually when you raise your hood look to the left or over to the passenger side against the side wall there will be a blue cap covering the washer fluid tank remove it fill the the tank and snap the lid back into place.

Nov 13, 2015 | Honda CRV Cars & Trucks

1 Answer

2005 mustang drivers seat wont move forward, where is the fuse located?


The fuse is located in the motor compartment, passenger side behind the windshield washer reservoir. There is a cover over this power distribution box, pull on the latches on the front and back of this box, remove the cover and flip it over, the fuse will be #14, located at the front right side of the box. It will be a 30 amp cartridge fuse. Check it, if it is good, your problem lies elsewhere.

Mar 08, 2014 | 2005 Ford Mustang V6

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

2 Answers

How do i remove the alternator from my 2001 aztek


you have to remove the washer fluid tank, battery ,and full windshield wiper assembly. there are three bolts that must be removed on the alternator, plus two wires. The alternator sits way in the back under the wiper assembly(passenger side). Almost impossible to get to, right against the firewall, must use a small ratchet wrench, NOT SOCKET-TOO BIG. Hope i could help


Dec 11, 2010 | 2001 Pontiac Aztek

1 Answer

Hjow do i rermove the radio from my 325 i 2003



Removal & Installation-of dashboard which includes removing radio.


CAUTION Many BMW models covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, properly disable the SRS.
The instrument panel removal is complex and requires disconnecting many components. Make sure to label and organize the components as they are disconnected, disassembled or removed.
3 Series Models

  1. Disconnect the negative battery cable. If equipped with a Supplemental Restraint System (SRS), wait for a period of 11 minutes before proceeding.
  2. If equipped, disable and remove the SRS components as necessary.
  3. Remove center console as outlined in this section.
  4. Remove the glove box compartment as follows:
    1. Open the glove box door and remove glove compartment mounting screws.
    2. Pull glove box compartment outward, and disconnect the electrical connectors as necessary.

  5. Remove lower left dash trim piece as follows:
    1. Remove the lower dash panel mounting screws.
    2. Pull the lower dash panel to the left and back and disengage it from the driver's side footwell retaining clips.

  6. If equipped, remove the driver's side and passenger airbags.


CAUTION Make sure to store the airbags properly in a safe area.
  1. Remove steering wheel.
  2. Remove driver side knee bolster fasteners and remove.
  3. Remove the following components:

    Instrument cluster Headlight switch Radio Climate control head and module.
  4. Remove the turn signal and windshield wiper/washer stalk switches as outlined in Section 8.
  5. Remove windshield (A-pillar) trim from both left and right sides.
  6. Remove the reinforcement bar below the steering column, then remove steering column shear bolts. Carefully lower steering lightly and support the column to avoid damaging the spindles.


WARNING Lowering the steering column too far can damage the spindles.
  1. Remove the glove compartment support frame fasteners, then remove the frame assembly.
  2. Carefully release and lift out the defroster outlets (both left and right sides) at base of windshield. Remove the screws located below the outlets.
  3. Remove the mounting bolts on the left and right sides of the dash board assembly.
  4. Carefully lift the instrument trim panel off slowly. Make sure all harness connectors and wiring are disconnected.
  5. Installation is the reverse of the removal procedure.

Z3 Models
  1. Disconnect the negative battery cable. Wait for a period of 11 minutes before proceeding.
  2. Disable and remove the (SRS) components as necessary.
  3. Remove center console as outlined in this section.


CAUTION Make sure to store the airbags properly in a safe area.
  1. Remove steering wheel.
  2. Remove driver side knee bolster fasteners and remove.
  3. Remove the following components:

    Instrument cluster Headlight switch Radio Climate control head and module.
  4. Remove the turn signal and windshield wiper/washer stalk switches as outlined in Section 8.
  5. Open the glove box, remove the four finishing caps near the glove box door lock catch and remove the screws.
  6. Remove the trim caps and screws from the far right end of dash and next to the center air vents on right side of the center console.
  7. Close the glove box, then pull it downward and out slightly.
  8. Remove the two screws securing the glove box cover and remove the cover.
  9. Remove the two fasteners securing the passenger side air bag bracket-to-support brace.
  10. Remove the two mounting fasteners on each end of instrument panel, in the door jamb areas.
  11. Remove the two mounting fasteners located under center air vents.
  12. Remove screw trim caps at the base of windshield and remove the screws.
  13. Carefully lift the instrument panel up and remove it from the passenger (right) side of the vehicle.
  14. Installation is the reverse of the removal procedure.

Nov 12, 2010 | 2003 BMW 325

1 Answer

How do you change out a left side mirror assembly on a 2005 town and country?


1. Pop off the triangular piece that is just cosmetic on the upper flat part of the mirror where it is attached to the van.
2. Under this piece are two visible bolts which you will need a Torx driver to remove.

3. Open the passenger door all the way open and remove the 3rd bolt, which is exposed from the outside of the car.
4. Expose the wiring harness plug by doing the following:
a. Pull off the door weatherstripping along the top of the door and on the pillar (the part of the car to the left of the windshield) Do not completely remove the weatherstip - simply pull it away enough to execute the next step.

b. Remove the plastic pillar cover: it simply snaps in. Pull hard and it will pop off
c. Lift up the plastic cover over the speaker on top of the dashboard. This piece goes all the way across the dashboard. Simply lift it up enough to get your hands underneath it. There is no need to free it from the passenger side.

d. Follow the mirror wiring harness around the rear of the speaker (the side nearest the engine) and unplug it from the female connector at the right-rear of the speaker. There may be a wire clip at the left-rear of the speaker that you will need to get the wire out of.
5. Unplug the wire, remove the mirror, replace the mirror, reinstall everything

hope its work

Jan 11, 2010 | 2005 Chrysler Town & Country

1 Answer

Where is battery


you need to remove 4 covers to replace the battery:
1. Cover over the windshield washer reservoir
2. Cover that says BATTERY on it
3. Cover that holds the battery cover
4. Cover over the bottom edge of the windshield on passenger side

Then you can access the battery easily! Hope this helps. let me know.

Dec 14, 2009 | 2006 Infiniti M35

1 Answer

I NEEDED THE 2001DODEGE CARAVAN SPECIFICATION


Hi,

2001 Dodge Caravan Performance Features -3,301 cc 3.3 liters 6 V engine with 93 mm bore, 81 mm stroke, 9.3 compression ratio, overhead valve and two valves per cylinder
-Unleaded fuel
-Fuel economy EPA highway (l/100km): 9.8
-Multi-point injection fuel system
-Main 76 liter unleaded fuel tank
-Power: SAE and 134 kW , 180 HP @ 5,000 rpm; 210 ft lb , 285 Nm @ 4,000 rpm
2001 Dodge Caravan Handling & Driving Features -ABS
-Two disc brakes including two ventilated discs
-Spacesaver steel rim under body spare wheel
-Strut front suspension with stabilizer bar independent with coil springs , beam rear suspension with stabilizer bar rigid with leaf springs
2001 Dodge Caravan Exterior Features -Body side molding
-Front and rear body color bumpers
-Driver and passenger power heated black door mirrors
-External dimensions: overall length (mm): 4,803, overall width (mm): 1,996, overall height (mm): 1,750, wheelbase (mm): 2,878, front track (mm): 1,600, rear track (mm): 1,626 and curb to curb turning circle (mm): 11,460
-Complex surface lens halogen bulb headlights
-Double sliding minivan side door
-Remote control operation opening rear ¼ windows
-Metallic paint , gloss paint , pearl paint
-Fixed rear window
-Tinted glass on cabin, rear and side
-Weights: curb weight (kg) 1,842, gross trailer weight braked (kg) 907 and max legal load (kg) 772
-Windshield wipers with variable intermittent wipe
2001 Dodge Caravan Interior Features -Air conditioning with rear outlet
-Fixed mast antenna
-Manufacturer's own audio system
-Automatic drive indicator on dashboard
-Below seat storage under passenger seat
-Cargo capacity: all seats in place (liters): 433, all seats removed (liters): 4,154 and third row seats removed (liters): 1,291
-Clock
-Dashboard full console with open storage box
-Delayed/fade courtesy lights
-Cruise control
-Front seats, rear seats and 3rd row seats cup holders
-Door ajar warning
-Door pockets/bins for driver seat and passenger seat
-Floor covering: carpet in load area
-Driver and passenger front airbag
-Bucket seat
-3-point reel height adjustable front seat belts on driver seat and passenger seat
-Front seat center armrest
-Glove compartment
-Height adjustable two head restraints on front seats, rear seats and 3rd row seats
-Internal dimensions: front headroom (mm): 1,011, rear headroom (mm): 998, front hip room (mm): 1,440, rear hip room (mm): 1,722, front leg room (mm): 1,031, rear leg room (mm): 930, front shoulder room (mm): 1,588 and rear shoulder room (mm): 1,643
-Low fuel level warning
-Low washer fluid level warning
-Internal button power locks
-Power steering
-Front power windows with one one-touch
-Front reading lights
-3-point reel height adjustable rear seat belts on driver side and passenger side
-Bench one-piece two rear seats
-Rear view mirror
-Upgraded cloth/velour seat upholstery
-Seating: seven seats
-Six speakers
-Plastic steering wheel
-Tachometer
-3-point reel third row seat belts on driver side , 3-point reel third row seat belts on passenger side , lap static third row seat belts on center side
-Front facing bench removable one-piece third row seats with capacity three
-Driver and passenger vanity mirror
-Ventilation system with recirculation setting
Thanks.

Jun 18, 2009 | 2001 Dodge Caravan

2 Answers

Repair a side mirror on a car


1. Pop off the triangular piece that is just cosmetic on the upper flat part of the mirror where it is attached to the van.
2. Under this piece are two visible bolts which you will need a Torx driver to remove.

3. Open the passenger door all the way open and remove the 3rd bolt, which is exposed from the outside of the car.
4. Expose the wiring harness plug by doing the following:
a. Pull off the door weatherstripping along the top of the door and on the pillar (the part of the car to the left of the windshield) Do not completely remove the weatherstip - simply pull it away enough to execute the next step.

b. Remove the plastic pillar cover: it simply snaps in. Pull hard and it will pop off
c. Lift up the plastic cover over the speaker on top of the dashboard. This piece goes all the way across the dashboard. Simply lift it up enough to get your hands underneath it. There is no need to free it from the passenger side.

d. Follow the mirror wiring harness around the rear of the speaker (the side nearest the engine) and unplug it from the female connector at the right-rear of the speaker. There may be a wire clip at the left-rear of the speaker that you will need to get the wire out of.
5. Unplug the wire, remove the mirror, replace the mirror, reinstall everything

Dec 22, 2008 | 2001 Chrysler Town & Country

Not finding what you are looking for?
1995 Oldsmobile Cutlass Ciera Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...