Question about Dodge Ram Pickup 1500

Open Question

I need the torque specs for a 2004 dodge ram 1500 4.7 harmonic balancer

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
captaynkyrk
  • 170 Answers

SOURCE: Harmonic balancer

Check out this link: http://www.autozone.com/addVehicleId,1602402/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c152800cc1e1. This is for a 6 cylinder in your year. This gives you the specs for all of the bolts associated with the crankshaft damper. Good Luck!

Posted on Jul 16, 2008

Ad
  • 74 Answers

SOURCE: Harmonic balancer for 1999 dodge ram 1500

rotation is left hand thread nut is too small to fit a wrench on with fan clutch on so leave belt hooked up on all pulleys .i use a air hammer! no air?use a big screw driver flathead and a hammer ketch the corner of nut going to the right hit screw driver about two or three times till fan clutch nut moves a litt no special tools needed!

Posted on Aug 26, 2008

  • 178 Answers

SOURCE: 1998 dodge ram 1500 pick up (not 4wd)

easier on lift if not ramps on ground chalk wheel use stands once all belts are off remove center bolt on bottom crank pulley install crank pulley remover you may have to remove outer part of split pulley thread three puller bolts into bal there should be holes for this snug all three tight install adapter into center where main bolt came out thread tool against adapter as you tighten in the bal pulls out once out replace timing case seal at bottom of cover lightly apply grease or lithium on inside of seal put new bal alighn on keyway install reinstall tool slowly with air ratchet or impact gun reinstall slowly the grease on seal will stop seal from dry start up once bal all the way in install center bolt outer pulley if taken off belts etc

Posted on Sep 11, 2008

  • 27 Answers

SOURCE: i need all torque specs main bearing caps

haynes manual is the best way

Posted on Oct 07, 2009

iambanshee74
  • 3489 Answers

SOURCE: I need the torque specs for the wheels on a 1997

you can set these at anywhere between 100ft lbs torque- 110. anything more is overkill. happy holidays

Posted on Dec 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS THE HARMONIC BALANCER TORQUE SPECS FOR A 2002 2.7L DODGE INTREPID?


This is for a 5.7 Ram
the torque should be 150-180 ft lbs. anywhere in this range is good.
http://www.fixya.com/cars/t8915727-need_know_torque

Register at this website to get all the torque specs.

http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f8037c5e2

Aha, I took me 30 minutes, but here you go. The secret was the change of search query wording to;
2002 2.7 DODGE INTREPID TORQUE SPECS crankshaft damper

(198) Install damper center bolt. Tighten center bolt
while holding the damper with Special Tool 8191 to
170 N•m (125 ft. lbs.) (Fig. 76).

http://www.dodgeintrepid.net/18-general-discussion-second-generation/61664-so-your-2-7-ready-some-100k-repairs.html


WHAT IS THE HARMONIC BALANCER TORQUE SPECS FOR 2002 2 7L DODGE INTREPID...

Jan 11, 2017 | 2002 Dodge Intrepid

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

Need torque specs for front wheel bearing on 2004 dodge 3500 dually


The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

Mar 23, 2014 | 2004 Dodge Ram 3500 Truck

1 Answer

Need torque specs. for water pump to 2004 chrysler pacific


I am certain I have the information you need. The problem is I am having trouble locating it in the FACTORY service manuals, terminology differs from what your searching for.

Torque for the Vibration Damper bolt is 115 Nm (85 ft.lbs.)

I am still trying to locate the pump torque.

Mar 28, 2013 | 2004 Chrysler Pacifica

1 Answer

Need to know torque for harmonic balancer bolt for 1998 Dodge Ram 1500 5.9 engine?


the torque should be 150-180 ft lbs.anywhere in this range is good.

Apr 10, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

I need a belt diagram for a 2005 Dodge Ram 1500 with the 4.7L?


Hello. Looking at your engine from the FRONT of your truck. Starting at the very bottom at the harmonic balancer...Your serpentine belt goes from the balancer (to the right) outside the next two pulleys. The third is inside the pulley, outside the fourth and fifth, then inside the last one to the outside of the balancer. I hope this helps, good luck, and.. Thank you for trusting FixYa to help get you going!

Apr 26, 2010 | 2005 Dodge Ram 1500

1 Answer

2004 Dodge Ram 2500 Hemi


sounds like the harmonic balancer on the crankshaft is coming loose, check it by trying to twist or turn it by hand

Sep 21, 2009 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...