Question about Isuzu Rodeo

2 Answers

Where is the engine drain plug located in order to drain coolant from the engine block?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 14,036 Answers

YOU HAVE CORE PLUGS ON SIDE ENGINE CYLINDER BLOCK AND ONE CORE PLUG ON THE FLYWHEEL END OF THE CYLINDER BLOCK.

Posted on Apr 01, 2011

  • Jonah Oneal Apr 01, 2011

    IF YOU WANT TO REMOVE COOLANT OUT OF ENGINE BLOCK BUY A FLUSH KIT AT ANY AUTO PARTS STORE. HOOK TO GARDEN HOSE AND FLUSH OUT COOLANT IN THE ENGINE BLOCK..ONLY TIME REMOVE CORE PLUGS IF YOU DOING A ENGINE OVER HAUL OR YOU HAVE TO REPLACE A LEAKING CORE PLUG.

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 693 Answers

Theres not, Need to disconect bottom radiator hose and turn over without starting to long. Just taks about 10 sec. Good luck to you. PS. you have a frezze plug on your block but this is not something you twist and remove Is a cap that fits into your engine.

Posted on Apr 01, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Kia Carnival. Q1 coolant capacity Q2 where is the engine block drain plug located


As you have not said which engine is fitted luckily it is the same for both the 2.9CRDI and the 2.5,the coolant capacity is 9.4ltrs, as far as I know there isn't an engine drain plug for the coolant, removing a hose is normally enough to drain it when you open the top engine coolant cap (DO NOT OPEN ON HOT ENGINE).

Nov 28, 2016 | Kia Carnival Cars & Trucks

1 Answer

A diagram of the flushing of a radiator and block of a chevrolet blazer LS 2000


Theres no such thing as a diagram, here are the draining instructions, hope this helps...
  • 1-Place a large drain pan beneath the radiator drain plug. The drain plug is located on the passenger side at the very bottom of the radiator on the engine side.

  • 2-Make sure the engine is cool. Open the hood of the truck and remove the radiator cap.
  • 3-Loosen the drain plug. On the 2000 Blazer, the drain plug is a wing-nut type of plug. Twist it with your fingers until the coolant begins to drain.

  • *To flush the block, once you have drained the radiator, run the engine for a bit untill the temp gauge goes up to normal, then the coolant will have been evacuated from the block. DO NOT leave the engine on, once it reaches normal temp, (this will happen quick) turn off right away, otherwise you'll be forking out a few hundred $$$ to fix the worped heads.
    4-Tighten the drain plug with your fingers once the coolant has drained fully from the radiator. Remove the drain pan and dispose of the used coolant properly.
    Some service stations will take and recycle your used coolant.
    Hope this helps...



  • Read more: How to Drain a Radiator From a 2000 Chevy Blazer ' eHow.com http://www.ehow.com/how_6357264_drain-radiator-2000-chevy-blazer.html#ixzz1VS4RBufX

    Aug 19, 2011 | 2000 Chevrolet Blazer

    1 Answer

    Where is the thermostat on my 2002 audi a 4 located


    Hello,

    The thermostat of a 2002 audi a4 is located between the engine and the radiator. The thermostat is small and crucial. It is meant for the vehicles cooling system. It moderates the flow of coolant into the engine by releasing it when the engine need it the most. The thermostat is designed to open its valve once the temperature of the engine reaches about 200 degrees F. Its purpose is to keep the engine running at a consistent temperature, allowing your Audi A4 to operate at peak performance.

    If You are planning on replacing the thermostat, here are the steps to follow to replace them, try to get these instruments (Car ramps, 4-by-4 inch wood block, Metric socket wrench set, Socket extension, Pliers, Drain pan, Empty plastic container, Black marker, Towel, Emery cloth, Gasket seal) then follow the steps below:
    1. Raise the front end of your Audi A4 by driving up on a set of car ramps and placing your vehicle in park.
    2. Place a 4-by-4 inch wood block behind one of the rear tires to keep the vehicle from rolling backward.
    3. Use a socket wrench to remove the pan that covers the bottom of the engine.
    4. Locate the red plastic cap that was behind the pan that you just removed. This red cap is your radiator drain plug. Remove the radiator cap from the top of the radiator and then place a drain pan under the red drain plug and turn it with a pair of pliers to allow the coolant to drain completely from the radiator. Once the coolant has completely drained, turn the drain plug to close it off. Be careful when using the pliers on the drain plug that you do not snap the plug off.
    5. Slide under the vehicle and locate the thermostat housing that is sitting just above the oil pan drain plug. Pour the drained coolant from the drain pan into an empty plastic container and label the container so that you do not reuse the expelled coolant. Place the empty drain pan under the thermostat housing before you attempt to remove the housing to allow the coolant from the engine to drain into it.
    6. Remove the 10 mm bolts that hold the thermostat housing on the engine block with a metric socket wrench. Do not lay directly underneath the thermostat housing as the coolant from the engine will begin to drain as soon as you loosen the bolts on the housing. Keep a towel or cloth with you to clean off any spilled coolant .
    7. Remove the thermostat housing from the engine and lift the old thermostat out of the housing. Use a piece of emery cloth to clean the face of the thermostat housing and the engine block where the housing is mounted from any remaining gasket material or debris.
    8. Spread a layer of gasket seal around the face of the thermostat housing and place the new thermostat on the housing, with the thermostat spring facing out from the housing. Position the housing back on the engine block and secure it to the block with the bolts.
    9. Replace the pan the sits across the bottom of the engine of your Audi A4 and then refill the radiator with coolant and put the radiator cap back on the radiator. Remove the wood block from the back tire of your vehicle. Turn the engine on and drive the Audi A4 off of the car ramps. Allow the engine to run at idle for a few minutes to verify that the thermostat is working properly and then shut the engine off.
    Hope this helped. Thank You for using FixYa!!!

    Jan 27, 2011 | 2004 Audi A4

    2 Answers

    Were is the drain plug located on a 2007 chevy 5.3 on the passenger side of engine . is it behind the ac unit. i want to put a engine block heater in.


    The block drain is on the passenger side of the engine, in the center of the block near where the oil pan attatches to the block.

    Engine Block Plugs/Sensors


    Engine Block Plugs/Sensors
    100 - Engine Block
    100 - Engine Block
    101 - Oil Gallery Plug - Front
    110 - O-Ring
    111 - Oil Gallery Plug - Rear
    112 - Oil Gallery Plug - Side
    113 - Washer
    114 - Engine Coolant Heater
    115 - Washer
    116 - Oil Gallery Plug - Side
    117 - Washer
    130 - Transmission Housing Locating Pin
    145 - Washer
    146 - Engine Block Coolant Drain Hole Plug
    701 - Crankshaft Position (CKP) Sensor
    702 - O-Ring
    718 - Knock Sensor
    718 - Knock Sensor
    739 - Bolt
    739 - Bolt
    750 - CKP Sensor Bolt

    Oct 19, 2010 | Chevrolet Silverado 1500 Cars & Trucks

    3 Answers

    Where is the drain plug for the radiator


    Should be a drain **** at the bottom of the radiator that unscrews out. It looks like a wing nut has been welded to a bolt on the end of it. Another way to do this is just pull off the bottom hose.

    Mar 31, 2010 | 2001 Jeep Cherokee

    2 Answers

    How do you drain coolant in a 1999 Chevrolet Suburban? specifically from the engine block?


    The easiest way to drain coolant from engine is to remove lower radiator hose from water pump and let it run out. There are no drains on the engine.

    Sep 07, 2009 | 1999 Chevrolet Suburban

    2 Answers

    Draining the Engine Block of Coolant.


    the drain plug is under the front of the truck on the drivers side back of the radiator. you have to turn it to open it .

    Mar 01, 2009 | 2000 Pontiac Montana

    1 Answer

    I replaced the alternator on my 2003 Range Rover


    I Suspect that you have AIR in your COOLING SYSTEM Fallow Procedures BELOW to Insure there is NO AIR IN COOLING SYSTEM


    Draining and Filling Cooling System

    Draining Procedure

    Important: Do NOT add any engine coolant supplement sealant pellets to the cooling system. Drain and refill the engine cooling system every 5 years or 240,000 km, (150,000 mi) , whichever occurs first.

    1. Park the vehicle on a level surface.
    2. Remove and clean the coolant recovery reservoir.
    Caution: Refer to Radiator Cap Removal Caution in Service Precautions.

    1. Remove the radiator cap when the engine is cool:
    3.1. Slowly rotate the cap counterclockwise to the detention tab. Do not press down while rotating pressure cap. 3.2. Wait until any residual pressure, indicated by a hissing sound, is relieved. 3.3. After all hissing stops, press down on the radiator cap and rotate the cap counterclockwise in order to remove the cap.
    Important: Recover and store used coolant in a used coolant holding tank and submit the used coolant for recycling on a regular basis. Do NOT pour used coolant down the drain. Ethylene glycol antifreeze is very toxic. Disposing of ethylene glycol into the sewer system or ground water is both illegal and ecologically unsound.

    1. Place a drain pan under the radiator drain valve in order to collect all of the used coolant.
    2. Open the radiator drain valve located at the bottom of the radiator tank. If only partial cooling system draining is required, drain enough coolant to perform the procedure.
    3. Open the air bleed valve on the thermostat housing 2 full turns
      1. Open the air bleed valve above coolant pump 2 full turns.
      2. Place a drain pan under the engine block drains in order to collect the used coolant.Important: Allow the coolant to drain completely.

        1. Remove both of the engine block drains.
          • The front left engine block drain is located between the starter motor and the engine oil filter.
          • The rear right engine block drain is located near the crankshaft position sensor.
        Filling Procedure
        Reinstall the engine block drains
      3. Close the radiator drain valve,
        1. Install the coolant recovery reservoir. Notice: When adding coolant, it is important that you use GM Goodwrench DEX-COOL or HAVOLINE DEX-COOL coolant. If Coolant other than DEX-COOL or HAVOLINE DEX-COOL is added to the system the engine coolant will require change sooner; at 50,000 km (30,000 mi) or 24 months.
        2. Slowly add a 50/50 mixture of GM Goodwrench DEX-COOL or HAVOLINE DEX-COOL and clean, drinkable water to the radiator until the coolant level is at the base of the radiator fill neck.
        3. Wait for 2 minutes and reinspect the level of the coolant in the radiator. If necessary, add coolant to the radiator until the coolant level is at the base of the radiator fill neck.
        4. Install the radiator cap.Ensure that the radiator cap arrow points toward the radiator overflow tubeImportant: The air bleed valves are brass. Do NOT over-tighten the air bleed valves.

          1. Close the air bleed valve above the coolant pump.
            1. Close the air bleed valve on the thermostat housing.
            2. Fill the coolant reservoir with a 50/50 mixture of GM Goodwrench DEX-COOL or HAVOLINE DEX-COOL and clean, drinkable water. Caution: Refer to Radiator Cap Removal Caution in Service Precautions. Important: If the coolant temperature indicator turns ON, turn the engine OFF immediately and allow the engine to cool. Do NOT remove the radiator cap.
            3. Start the engine and allow the engine cooling fan to cycle on and off 3 times. If the low coolant indicator does not turn OFF and the coolant level is above the Full Cold mark on the coolant recovery reservoir, refer to Engine Coolant Temperature Gage Inaccurate or Inoperative.
            4. Turn off the ignition.
            5. Allow the engine to cool.
            6. Ensure that the engine coolant concentration is sufficient.

    Feb 21, 2009 | 2001 Pontiac Aztek

    2 Answers

    Engine block coolant drain plug location


    They are on the side of the engine block, there will either be a pipe plug or a sensor in the threaded hole(s)

    Aug 22, 2008 | 2007 Chevrolet Tahoe

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    247 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Isuzu Experts

    yadayada
    yadayada

    Level 3 Expert

    75005 Answers

    Steve Hurc
    Steve Hurc

    Level 3 Expert

    450 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Are you an Isuzu Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...