Question about 2005 Chevrolet Malibu Maxx

Open Question

How do I remove the front seat head rests so i can install my seat covers?

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: cannot get adjustable head rest off the seat

On the plastic pieces surrounding the insertion hole on top of the seat back,there is a very very tiny hole on the side of this piece of plastic. You need to insert a rigid piece of wire or a very fine nail of some kind into this small hole and push until you feel it give, then pull up on the headrest. it should come out. You have to do this on each of the two insertion holes. It's easier with two people.

Posted on May 13, 2009

motor1258
  • 6674 Answers

SOURCE: how do you take out

Not much info on vehicle but look at area where headrest goes into seat, for a small spot where you can push in to release and then pull up headrest at same time.

Posted on Nov 13, 2010

  • 14585 Answers

SOURCE: I need to know how to remove the head rest on the

99% just pull out, the other s have a button on the seat right at the head rest.

Posted on Feb 07, 2011

  • 213 Answers

SOURCE: How do I remove the

see a plastic cap type thing attached to the seat where the rod of the headrest goes in feel this cap and you wil find a puch button press it and pul the head rest

Posted on Feb 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the rear bench seat on a Galant 2010 to install seat covers? Thanks


push back firmly at front of seat at bottomlocating clip released with upward preasure

Nov 14, 2012 | 2010 Mitsubishi Galant

1 Answer

How do I remove the head rest on the front seats of my 2002 Chevy Silverado crew-cab to allow me to install customized seat covers?


see a plastic cap type thing attached to the seat where the rod of the headrest goes in feel this cap and you wil find a puch button press it and pul the head rest

Feb 07, 2011 | Chevrolet Silverado 2500HD Cars & Trucks

1 Answer

We need to remove the drives side head rest to install a seat cover, but we cannot figure out how to remove the head rest. How do you remove the driver's side head rest?


Head Restraints Removal
  1. Unscrew front seat head rest guide rod retainers (610A18) .
  1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .

    Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
  1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .

9a4d433.gif

Aug 21, 2010 | 1998 Ford Taurus

1 Answer

How to remove the head rests on the front seats of a 1998 Lexus LS400 to install seat covers


there is a small push in clip at the bottom of one of the small chrome shafts. you push it in while you pull the head rest up.

May 17, 2009 | 1998 Lexus Gs 400

1 Answer

How to remover 2008 f150 supercrew front seat head restriants


There should be two little buttons under the head rest (one on each side of the bars) they should pull out slightly and you should be able to raise each one. If you are trying to remove them completely, i believe there are tiny screws that hold the bar retainers in place on top of the seats. Hope this helps.

Mar 14, 2009 | 2008 Ford F 150 2WD

1 Answer

How do you remove the headrest on a 1996 ford crown victoria?


Head Restraints Each front seat is equipped with dual-post design front seat back head restraint (611A08). The front seat back head restraint is installed as follows:
  • It travels on dual posts which have notches to engage a spring-loaded catch in the guide.
  • The front seat back spring assembly retains the front seat head rest guide rod sleeve (610A16).
  • The front seat back head restraint is adjustable from its normal position to a raised position of approximately 25 mm (1 inch).
  • Pull up on the front seat back head restraint to raise it. Pushing down will return it to its normal position.
----------------------------------------------------------------------------------------------

Removal
  1. Unscrew front seat head rest guide rod retainers (610A18).
  1. Pull up on front seat back head restraint (611A08). Compress foam in area of front seat head rest guide rod sleeves (610A16).
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves.
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve.

    Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint.

Mar 01, 2009 | 1996 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...