Question about Suzuki Grand Vitara

1 Answer

My driver side headlights will not come on. I bought a new bulb and it still will not come on. What could the problem be?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

Abad fuse or bad ground and or connection test for power at the plug with a test lite

Posted on Apr 01, 2011

Testimonial: "Great feedback!"

  • Jamiwi Tixu Jun 02, 2011

    Few drivers take the time to consider anything about their headlights than how to work with them. The history and technology behind them is interesting. Knowing how your front lights work is helpful for maintaining them and crash-avoidance purposes. I read this here: Get to know more about your headlights, cardealexpert.com/news-information . For the driver's safety,car needs tender care for a good road travel.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Driver side headlight bulbs burned out on 2003 VW Golf

There is a light cover in front of the battery... take this off and then look for the metal clamps holding the light housing in.  (I say clamps, but they're more like glorified paper clips on either side of the fixture.)  Press in on each side, pushing the clamps towards each other and pull the fixture out.

Posted on Dec 04, 2008

  • 5 Answers

SOURCE: 99 cutlass supreme headlight bulb replacement

Look at the top of the headlight assembly. There is a plastic panel on top of the assembly that is held in place by two plastic pins. Remove those pins by lifting the center of the pin and then pull out the pin. Remove the panel. Then you will find two small plastic levers that will lift about 1/2 inch. They do not come out but they will release two studs that secure the assembly. After the assembly is released, slide it forward to access the bulbs you need to replace. Installation is the reverse of these procedures.

Posted on Mar 08, 2009

  • 383 Answers

SOURCE: 2001 subaru outback headlight not working

chapmnfarm: your head lights use a "2" fuse system.
one for the left and one for the right.
The fuse box you are looking for is under the hood on the passenger's side. It is a black box roughly 8 inches long and 4-5 inches wide. When you remove the cover, you will see fuses and relays. What you are looking for is the section in the box which has a cluster of 7 fuses. 3 in one row and 4 in the other. On the outer parameter are two relays. The fuses you are interested in are located in the row of 4 fuses, with the two closest to the "L" shaped part of the box. Both of those should be 15 amp fuses.
The fuse below those should be a 20 amp which is the lighting switch and the one below it is a 15 amp which is for the interior lights and the clock.
Check your harness grounds in the engine compartment near the area you have the problem. There are ground wires which come out of the harness on both sides of the core support. The wires are black in color and have "EYES" crimped onto the ends of the wires. Both of them will probably be located about 4-6 inches below the upper tie bar on each side of the radiator. Odds are that the eyes will be large enough to pass a 6mm bolt through.
I hope what I have given you will resolve your problem. Lem me know,,good luck>>>>>>>>>>>>>>>

Posted on Apr 19, 2009

  • 37 Answers

SOURCE: Headlight bulb replacement for 2002 Hyundai

http://www.autozone.com/autozone/repairinfo/common/repairInfoMain.jsp?targetPage=productsHowToInspect&leftNavPage=productsHowTo&pageId=%090900c15280213e7e&subtitle=replace

Posted on Apr 23, 2009

techbuster
  • 5081 Answers

SOURCE: How do you replace the drivers side headlight bulb

1. Remove headlight housing. A.Open Hood and pull the release lever at the back of the housing. The headlight housing slides in and out of the body in tracks. B.Pull out the headlight housing far enough to disconnect the electric connectors, then slide the housing completely out. 2. Remove the retaining clip to remove the upper (low beam) or lower (high beam) bulb from the holder from the back of the housing unit. Remove the old bulb(s). 3. Do not touch the bulb with your bare hands! Wear clean gloves or hold with a clean paper towel. Fingerprints on the bulb will cause the bulb to burn out or explode!. Insert the new bulb. 4. Replace the retaining clips and insert the housing back into the tracks and into the body. Plug the electric connectors in and insert the housing completely. 5. Reposition the release lever to the original position being careful not to break the plasic lever. 6. Check your lights for operation.

Posted on Nov 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have a 2007 Chrysler sebring and drivers low beams will not work.


try the fuses or wire fuse links , the only other thing in the circuit is the wires broken or the light low switch is bad

Nov 08, 2014 | 2007 Chrysler Sebring Sedan

1 Answer

2006 Volkswagon Beetle, drivers side headlight, high beam not working


Instructions
    • Turn the headlight switch on and inspect the headlights. Make sure to check both low- and high-beam lights, and then note the position of the bulb in the headlight assembly. Low-beams are in the top cavity of the assembly and high-beams are in the lower cavity.
    • 2Turn off the headlight switch and then remove the keys from the ignition.
    • 3
    • Open the hood and locate the seam to the headlight assembly and the side fender. Locate the headlight assembly release lever and push in on it slightly to unlock it and then pull it all the way up until it stops.
    • 4Place a blanket or pillow on the ground in front of the headlight assembly. Push the assembly outward from behind with one hand while being ready to catch the assembly with the other. The New Beetles use an adhesive sealant to protect the back of the headlights from exposure to moisture, so you'll have to give the assembly a push from behind.
    • 5Pull the wire harness plugs off from both the high- and low-beam blades of the respective bulbs.
    • 6Place the assembly on the blanket or pillow. Release the wire clip to the faulty headlight and then remove the headlight bulb.
    • 7Open the package of the new H1 bulb replacement without touching the glass portion of the bulb with your bare skin. Oils in human skin will damage the bulb. Handle it only by the metal base of the bulb insert.
    • 8Insert the new bulb in the appropriate headlight-assembly cavity and reattach the bulb retaining clip to lock the bulb in place.
    • 9Lift the assembly up and plug the wire harness plugs back into the respective blades of the bulbs.
    • 10Push the headlight assembly into its cavity, but before locking it in place, check the lights by turning on the headlight switch.

Sep 17, 2012 | 2006 Volkswagen New Beetle

1 Answer

Headlamp bulb replacement. Driver side head lamp is out. Bought new bulbs. Owners manual says to contact dealership for replacement. How do I replace the bulb myself? 2007 Mazda6


I ASSUME they are just regular headlights....not HID....correct??? just take off the cover and there is a small clip, just unclip it and remove bulb. If they are HID, then you better not try it.

Nov 12, 2010 | Mazda MAZDA6 Cars & Trucks

1 Answer

Cobalt 2005 ls headlight bulb replacement


Instructions Things You'll Need:
  • 9007 LL halogen headlight bulb
  • Wrench
  • Gloves or clean rag
  1. Step 1 Set the parking brake and remove the keys from the ignition to ensure your Chevy Cobalt won't roll while you're replacing the headlight bulb.
  2. Step 2 Open the hood by pulling the hood release latch located under the instrument panel on the driver's side of the car. Locate the secondary release latch on the front of the hood at the center, slightly towards the driver's side. Slide the latch to the left to release the hood and raise it.
  3. Step 3 Locate the headlight assembly and remove the bolts by turning them counterclockwise. Set the bolts aside in a safe place, so you won't misplace them.
  4. Step 4 Remove the plastic fasteners from the headlight assembly molding. Carefully pull back the front fascia, or molding. You may need an extra pair of hands to perform this slightly awkward task.
  5. Step 5 Grab the headlight assembly and pull it towards the radiator at a slight angle to remove it. This should provide easier access to the headlight bulb and wiring harness.
  6. Step 6 Lift the plastic locking tab on the wiring harness to disconnect the bulb base. Then, disconnect the wiring harness from the bulb socket and remove the black retainer by turning it counterclockwise.
  7. Step 7 Disconnect the bulb socket by turning it counterclockwise. Remove the old bulb from the socket by firmly, but gently pulling it straight out.
  8. Step 8 Replace the old bulb with a new 9007 LL halogen headlight bulb. Put your headlight assembly back together by reversing the steps when you disassembled it. Use 89 inch-lb torque when retightening the headlight assembly

Feb 26, 2010 | 2006 Chevrolet Cobalt

1 Answer

Fender bender, bought new assembly. How to remove old for replacement? "89 seville driver side headlight.


LIGHTING Headlights REMOVAL & INSTALLATION
  1. Unscrew the Torx retaining screws and remove the headlight bezel.
  2. Remove the headlight bulb retaining screws. These are the screws which hold the retaining ring for the bulb to the front of the car. Do not touch the two headlight aiming screws, at the top and the side of the retaining ring (these screws will have different heads), or the headlight aim will have to be re-adjusted.
  3. Pull the bulb and ring forward, then separate them. Unplug the electrical connector from the rear of the bulb.
  4. Plug the new bulb into the electrical connector. Install the bulb into the retaining ring and then install the ring and the bulb. Install the headlight beze

Aug 23, 2009 | 1989 Cadillac Seville

2 Answers

Lightbulb driver side 2008gmc 3500 6.6l


how to change driver side headlight bulbs?

May 30, 2009 | 2008 GMC Sierra 3500HD 2WD

3 Answers

One headlight dimmer than the other


you've got a grounding wire issue on the right side headlight.
trace the wire that goes to ground and make sure the connection is clean and tight... check for corrosion around the wire terminals and in the connector...

May 27, 2009 | 1985 Chevrolet Sprint

1 Answer

Headlights


check headlight relay

May 05, 2009 | 2004 Chevrolet Cavalier

1 Answer

Driver's side Headlight Bulb Replacement


Do you mean the entire headlight assembly or just the bulb?
If it's the entire headlamp look at the new one to see where the fastening points are, the grill may have to be removed and also the parking lamp lens, if it's just the bulb it's easy Open your hood look at the back of the headlight assembly and twist the bulb holder ring to release it. Good Luck To You

Jan 20, 2009 | 2008 Honda Element

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...