Question about Ford Crown Victoria

Open Question

Where is the air compressor located on a 99 crown vic for the air suspension?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
RJones1125
  • 373 Answers

SOURCE: where is air suspension compressor located on '94 lincoln towncar

engine compartment, driverside fender well

Posted on Feb 28, 2009

Ad
chrischronic
  • 235 Answers

SOURCE: locating the air suspension compressor on 1991 linoln town car

Its under the windshild washer reservoir ,under the hood on drivers side.

Posted on Dec 23, 2008

  • 9 Answers

SOURCE: air suspension compressor

It's located in the front under the hood, between your windsheild washer fluid and the front of the truck. It's set down kind of below the washer fluid.

I hope that helps.

Posted on Jan 15, 2009

  • 599 Answers

SOURCE: My 99 Crown Vic acts like it isn't getting gas

check for clogged fuel filter first, usually the pump works or it dosen't, check and get back to me.

Posted on May 01, 2009

  • 5522 Answers

SOURCE: Wiper motor replacement for a 99 crown vic

I replaced the same part on a 1994 Crown Vic. There are a few bolts which go through rubber mounts on the firewall and that is how the wiper motor fits against the firewall. There is a clip on the wiper drive that must be pressed and slid off the wiper shaft. The hardest part was getting clearence between the engine and wiper motor. If I remember there was a way to turn the wiper case to clear the engine. I have asked myself why this was engineered like this? There is nothing important in the way that 3/4" of clearance could have been given for removal.

Posted on May 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 crown Vic air suspension/compressor disconnected took vehicle to shop they discomnected compressor. am trying to reconnect and cant figure it out all fuses okay trunk switch okay located...


Check the pump. it is located under the wiper fluid container. Thats where I would start. are you interested in selling it? I'm looking for a black 96 with low miles...

Feb 26, 2011 | 1996 Ford Crown Victoria

1 Answer

Hi, I have two questions 1st) can anyone tell be where the relay for a 1999 crown vic air suspension is located? 2nd) can I hook wires directly from battery to air compressor, bypassing relay, in order to...


YES YOU CAN,SHOULD BE IN YOUR OWNERS MANUAL,WHAT YOU WILL HAVE TO DO IS REMOVE PASSENGER SIDE HEADLIGHT ASSEMBLY AND SPLICE THE TWO WIRES GOINT TO THE COMP AND HOOK STRAIGHT TO THE BATTERY.








TIM

Feb 20, 2011 | 1999 Ford Crown Victoria

2 Answers

1992 CROWN VICTORIA LX I REPLACED FUSES INSIDE AND UNDER HOOD FOR AIR RIDE SUSPENSION AND IT STILL WON'T AIR UP. PLEASE HELP


Air ride suspension basically works like this. you have a small air compressor and a sensor that connects between the rear axle and the under body Frame. When this sensor detects a load movement like more or less weight it turns on the air compressor to air up or opens a exhaust valve to let air out. most common problems with this system. broken or disconnected sensor. leak in the air lines between compressor and shocks. or a bad or weak compressor.

Feb 08, 2011 | 1992 Ford Crown Victoria

2 Answers

I have 94'crown vic with rear air ride suspension problems. The back end won't rise. Any help is appreciated.


Start by checking the fuses for the air compressor for the rear suspension. these will be listed in your owners manual. Failing this it could be the compressor motor or wiring to the motor, unless you can hear the compressor working. If the compressor is running but not adjusting the back of the car then you have an air leak in one of the shocks or air lines.
if you find it is a fuse, also listen for the compressor motor running and an air leak, if the system is running constantly to make up for a leak , that may be what blew the fuse.

Hope this helps
Ed

Mar 29, 2010 | 1994 Ford Crown Victoria

1 Answer

1998 crown vic air suspension compressor does not pump.


Sounds like the problem is in the air bag suspension, not the compressor. The air bags shouldn't be losing air when the car sits. The compressor adjusts the suspension level according to the load. The air bags have a valve similar to a blow up raft that allows air to pass through both ways. If when the car is running the compressor is constantly running and not turning off, the issue is within the air bags and/or the air line.

Sep 05, 2009 | 1995 Ford Crown Victoria

1 Answer

How do I reconnect my 95 Crown Vic air suspension compressor?


most likely someone unhooked it due to some part being bad in the system and even possiable that the air bags have been removed and coil springs installed

Jul 15, 2017 | 1995 Ford Crown Victoria

1 Answer

How does one reconnect the air suspension


You probably have a leak in the system. Did "they" check the lines and air suspension? "They" probably disconnected the compressor to keep it from burning out from overuse. You need to fix the leak before reconnecting or the compressor will wear out very quickly.

Aug 09, 2009 | 1995 Ford Crown Victoria

5 Answers

The trunk of car is low to the ground, the frontend is high


It sounds to me like your compressor got killed. What probably happened is that the airbag got a hole or tiny crack in it so the compressor has to work extra hard because it is like blowing up a balloon with a hole in it. Therefor the airbag killed the compressor. I would recommend going to strutmasters.com and taking a look at our conversion kits. these convert you from the airbag to a powder coated American made steel coil spring that is guaranteed to last the life of the car. I added the link below so you can check it out.
http://www.strutmasters.com/ford-suspension-parts-s/75.htm

I hope I was of some help
Good Luck!!!

Jan 21, 2009 | 1995 Ford Crown Victoria

1 Answer

Air suspension problem 92 crown vic


you can unplug it at the compressor end and supply your own power with a couple of bits of wire straight from your battery and does not interfere with the vehicles systems.Make sure you put positive to positive etcThat will tell you it operates.You will then have to remove outlet hose to check that it is creating any pressure.The pump should have a reciever drier that keeps moisture out of the air lines Considering the age of the vehicle that part is due for replacement.Do you have a test light/probe to check if you have power to the pump?You can do this test at the compressor plug.

Oct 17, 2008 | 1992 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...