Question about 2000 Chevrolet S-10

1 Answer

Trying to remove fan clutch,which way does it turn?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,036 Answers

YOU NEED TO HOLD FAN CLUTCH WITH A CLUTCH TOOL THEN LOOSEN THE LARGE NUT RETAINING THE FAN AND CLUTCH ASSEMBLY REMOVE FAN TO CLUTCH BOLTS AND NUTS COUNTERCLOCK WISE.

Posted on Apr 01, 2011

Testimonial: "Your right fan clutch nut comes off counterclockwise -righty tighty lefty loosey"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i remove the fan and pulley on a 1987 ford ranger 2.9 v-6?


The question is: How remove clutch in order to remove fan mounted on its engine-side face.
  • Generally, the clutch drive half shaft must be uncoupled from coolant pump (impeller drive) half shaft using special wrench kit available as loaner from AutoZone (free with $79 approx deposit).
  • Best done after shroud & radiator remove after coolant drained.
  1. Uncouple coolant pump and fan clutch drive shaft(s) as follows:
    1. span across combo-pulley-sheaves-unit mounting bolt heads with large tool kit wrench, and
    2. span inline clutch coupling nut with small tool kit wrench. Then,
    3. turn small wrench (and coupling nut) CW while resisting with large wrench (CCW) to turn coupling nut until disengaged from coolant pump drive shaft.
  2. Remove fan/clutch assembly.
  3. Note direction of mounted fan hub and fan blades orientation to ensure proper re-assembly.
  4. On rear of clutch assy, remove 4 bolts to disengage and remove fan.
  5. Assemble new fan to clutch (or, preferably, new clutch and new fan) using new bolts and washers provided with fan.
  6. Couple fan-clutch assy to coolant pump drive shaft as per opposite of uncoupling step 1, above. (Turn inline nut CCW to tighten...30 ft-lb.
  7. Check that fan can be hand turned...CW.)
  8. Rest shroud over and onto fan.
  9. Replace radiator; remount shroud; reclamp hoses, and refill and air purge cooling system.
remove-fan-pulley-1987-ford-ranger-2-9-v-2cg35myhodwcq1awmwat24pw-4-0.jpg

Aug 12, 2012 | 1987 Ford Ranger

2 Answers

Ford ranger fan clutch


There may be a tool, or you jam a metal tool between two metal parts.
check these out:


Removing Stubborn Clutch fan Ranger Forums The Ultimate Ford Ranger...

Fan clutch removal


Apr 11, 2017 | 1993 Ford Ranger SuperCab

1 Answer

HOW TO REPLACE CLUTCH FAN


to remove clutch fan you need to remove upper fan shroud, you need large wrench to remove the fan clutch retaining nut to remove fan and clutch away from the engine drive belt should keep pulley from turning while loosen fan clutch retaining nut.if pulley belt turns while loosen fan clutch bolt remove drive belt use strap wrench hold pulley while you remove fan clutch bolt this procedure for checvrolet if you working on volkswagon you need spanner wrench hold the idler pulley while you use large wrench to loosen the large drive nut to fan clutch. you have to remove fan with clutch from engine then you can remove clutch from fan you can go to auto parts stores rent a spanner wrench try auto zone they rent out tools.

Jan 05, 2012 | Cars & Trucks

1 Answer

95' ford econline 350 van replacing waterpump and clutch fan how to replace.


TO REPLACE WATER PUMP.REMOVE THE RADIATOR SHROUD HALVES.REMOVE FAN CLUTCH AND FAN.YOU NEED FAN CLUTCH WRENCH AND A FAN CLUTCH PULLEY HOLDER.YOU CAN RENT TOOLS AT AUTO ZONE OR BUY THEM AT A AUTO PARTS STORE.THE FAN CLUTCH BOLTS ARE LEFT HAND THREAD. REMOVE THEM BY TURNING CLOCKWISE.BEFORE INSTALLING NEW WATER PUMP COAT BOTH SIDES OF WATER PUMP GASKET WITH GASKET SEALER.TORQUE WATER PUMP BOLTS 18 FT LBS.

Mar 15, 2011 | 1995 Ford Econoline

2 Answers

TOYOTA PREVIA OVER HEAT WHEN IDLE


Sounds like the radiator cooling fan isn't turning on, i would unplug the fan and run 2 jumper wires direct from the battery to the fan if the fan kicks on the fan is good, if it doesnt the fan needs to be replaced, if the fan checks out i would check the fan relay and make sure the relay is good, if the relay turns out to be ok then the coolant fan thermo switch is most likely the culprit for the fan not engaging when the engine reaches a certain temperature....

Dec 07, 2010 | 1994 Toyota Previa

1 Answer

Im trying to take off the fan behind my raditor. what is the best way to do this? i removed the raditor and need to replace the fan now...


You will need a fan clutch tool or a large adjustable wrench. Some fans have reverse threads (ie: right = loosen, left = tighten) so take a look at the threads on the new fan to make sure your turning the fan the correct way. Keep the serpentine belt on to help stop the water pump from turning. There is a tool to stop the water pump from turning while removing the fan clutch. But usually a large clamp or pry bad used cautiously can do the trick. It wasn't necessary to remove the radiator to replace the fan.

Jul 31, 2010 | 2000 Chevrolet Blazer

2 Answers

How do you remove the fan from 1998 f150 4.2 liter


how do you remove the fan and fan clutch from 1998 f150 4.2 liter engine. i am trying to replace the water pump but i cannot get the fan to break loose . i cannot figure how to stop pump from turning while trying to loosen the bolt or nut that holds the fan clutch on the water pump shaft . is there a special tool to help me with this

Jul 15, 2010 | 1998 Ford F150 Regular Cab

2 Answers

How do you remvoe the radiator fan from the clutch on a 97 dodge ram pick up


To seperate the fan from the fan clutch there should be four small bolts that keep them together. Not sure thats what you are looking for but if you are trying to seperate the fanclutch from the water pump then you need a special tool to hold the pully from turning with the one hand while turning the fan clutch nut with the other they rent these tools at autozone.Once youve seperated the fan clutch from the water pump then you can take the fan off the clutch by removing the four small bolts.Please rate my assistance in helping you thank you.

Feb 13, 2010 | 1999 Dodge Ram

2 Answers

I am trying to remove the bolt for the fan clutch assembly on a 97 chevy blazer.


  1. 1 Remove the fan and clutch assembly from the fan's pulley. The assembly attaches to the pulley with several bolts on the circumference of the pulley. To remove the bolts, position an open-end wrench over each bolt and turn each bolt in a counterclockwise direction while grasping one of the fan's blades to prevent the fan from turning with the bolt.
  2. Step 2 Pull the fan and clutch assembly away from the engine, then lift the assembly out of the engine's compartment.
  3. Step 3 Remove the bolts which hold the fan to the clutch. The bolts are located on the back of the fan, and can be removed with a open-end wrench.
  4. Step 4 Place the fan and clutch assembly on a flat surface with the clutch facing up, then pull the clutch straight up to disengage it from the fan.

Nov 12, 2009 | 1997 Chevrolet Blazer

1 Answer

Need to take off fan clutch, have taken off parts in the way


4.9L SFI
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding Tool T84T-6312-C Fan Clutch Nut Wrench T93T-6312-B
Removal
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The large clutch assembly nut has a right-hand thread and must be rotated counterclockwise to remove it.
    Remove the fan clutch (8A616) from the water pump (8501) by turning the large nut, which is part of the fan clutch, using Fan Clutch Holding Tool T84T-6312-C and Fan Clutch Nut Wrench T93T-6312-B.
  1. Remove two screws retaining fan shroud.
  1. Remove the fan blade (8600), fan clutch and shroud.
  1. If the fan blade and fan clutch have to be separated, remove the remaining bolts attaching the fan blade to the fan clutch
b098d2e.gif


5.0L, 5.8L and 7.5L Engines
Removal
  1. Remove screws retaining fan shroud (8146) to radiator (8005).
  1. Remove four screws retaining clutch on water pump hub.
  1. Pull fan clutch and fan blade off water pump pilot and remove fan clutch, fan blade and shroud from vehicle.
  1. Remove four screws and separate fan clutch from fan blade.
4d17f8c.gif

Item Part Number Description 1 8509 Water Pump Pulley 2 57632-S Screw and Washer Assembly, 5/16-18 x .62 Hex 3 8600 Fan Blade (5.0 and 5.8L) 4 8600 Fan Blade (7.5L) 5 8A616 Fan Clutch 6 380288-S2 Screw and Washer Assembly, 5/16-24 x .88 Hex A — 16-24 Nm (12-18 Lb-Ft)

Mar 10, 2009 | 1994 Ford F150 Styleside Supercab

Not finding what you are looking for?
2000 Chevrolet S-10 Logo

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...