Question about 1995 Mercury Cougar

1 Answer

Waterpump pulling off the waterpump after everything is unbolted

Posted by on

  • jesserdixon Aug 05, 2008

    is there any special tool for it or should it just come off



×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

You should be more clear in your question. If you are sure that all bolts and belts are removed, it might be simply stuck because of the gasket sealant. Use a little brute force. Notice I said a little. No hammers, simply arm strength.

Posted on Aug 05, 2008

  • mgober Aug 05, 2008

    For removal? The only tools you should need for removal involve the bolts. Have you removed the timing belt and all other belts? Then the waterpump should pull off.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm having problems unbolting the fan hub from the waterpump


I find that If i place a flat bladed screw driver under the nut next to the one I wish to undo and lay it across the hub I have an effective bar with which to hold the hub as I undo the bolts/nuts. Undo 1 and then move onto the next one and repeat the process.

Mar 14, 2013 | Cars & Trucks

1 Answer

Waterpump


pull out your coolant res.
pull off your belt.
you will see the old waterpump.
remove all four bolts.
clean off gasket off waterpump mount on motor.
place gasket.
install.

Jun 30, 2012 | 1999 Pontiac Sunfire

1 Answer

I wanna know how to replace a water pump on my 1998 BMW 528i


You need to drain radiator, pull fan shroud, pull fan/fan clutch, reeve belts and pulley then unbolt waterpump. You do beed special tools for fan clutch and pulley removal. BavAuto.com or Pelican parts .com have parts, tools and good info on how to do the job successfully.

Mar 31, 2011 | 2000 BMW 5 Series

1 Answer

Wheres the waterpump located on a 98 mazda protoge lx?


Right Side of Engine Block...
The Follwoing instructions will tell you how to remove and replace:
  • Drain the engine coolant into a container that holds at least 6.3 qts. by twisting the plastic drain plug on the rear of the radiator.

  • 2

    Unbolt the air cleaner assembly. The assembly is on the right side of the engine compartment, to the rear of the battery. A single bolt on the right side holds it in place.

  • 3

    Squeeze the tabs on the air intake hose clamp where the hose connects to the engine and pull the hose loose. Remove the air cleaner assembly and hose.

  • 4

    Remove the insulating shroud from the exhaust manifold on the front of the engine. It is held on by four bolts.

  • 5

    Remove the timing belt.

  • 6

    Unbolt the water pump from the right side of the engine block. Unbolt the flange connecting the water line to the pump. Remove the pump.

  • 7

    Replace the pump. Installation is the reverse of removal

  • Feb 25, 2011 | 1999 Mazda Protege

    1 Answer

    How to install window regulator mitsubishi galant


    FOr the most part window regulators just unbolt and unplug. I'd suggest you go to a junkyard that lets you pull your own parts and then do it. Once you have pulled the replacement part you will know everything you need to know. Basics are you pull the door panel. Next you separate the glasss from the regulator unit. Now unbolt the regulator. Wedge glass up in the door and angle the regulator out of the opening

    Feb 22, 2010 | 2002 Mitsubishi Galant

    1 Answer

    How to change water pump


    drain coolant from radiator drain plug ,remove belt, remove waterpump pully and unbolt waterpump and remove .

    Nov 01, 2009 | 1993 Buick LeSabre

    1 Answer

    1997 Bonneville waterpump removal


    Are you talking about the Power steering pulley? Unbolt the pump, It is held on by two bolts and they are accessed thru the holes in the pulley. Just unbolt the pump and move it out of the way. Leave all the lines attached to it.

    Aug 20, 2009 | 1999 Pontiac Bonneville

    1 Answer

    Waterpump pulley removal


    Pulley unbolts from the front of the pump. Remove belt after you loosen the pump bolts. you can lean on the belt to keep the pulley from turning as you break the bolts loose.

    Mar 13, 2009 | 1996 Jeep Cherokee

    1 Answer

    Put new water pump on, cannot get belt back on


    Unbolt the pulley from the water pump, slip the belt over everything and refasten the the pulley to the pump while the belt is draped over it. Then tighten up the belt.

    Mar 13, 2009 | 1999 Nissan Sentra

    2 Answers

    Waterpump removal


    its easy you pull out the radiator and fans take the belts off and then its just unbolting it and rebolting it. I just did it a couple hours ago. you should replace your rad hoses when you do this and also your belts.

    Aug 09, 2008 | 1995 Dodge Intrepid

    Not finding what you are looking for?
    1995 Mercury Cougar Logo

    Related Topics:

    93 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mercury Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Are you a Mercury Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...