Question about 2000 Ford Taurus

1 Answer

Need to replace pc valve on 2000 Ford Taurus. Can't find it.

Posted by on

1 Answer

Should find it on valve cover

Clean it every 3 years & put it back

Spray it with Brakleen etc

It only stops oil from leaving
the valve cover,no other function

As long as the hose doesn't
have a vacuum leak, you all set

The PCV Valve will last 20 years

Posted on Mar 31, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my ford taurus idle high code P1506


The code is for the idle air control valve which controls idle speed.
The problem could be a faulty control valve, or a vac leak which is letting in air to the intake and bypassing the control valve.

Jan 19, 2013 | 2000 Ford Taurus

1 Answer

Where is the dpfe sensor located on the 2000 ford taurus?


I had to replace the dpfe sensor on my 2000 Ford Explorer and they should be the same.
Mine was located on the left side of the engine (facing the engine with the hood up) above the valve cover. It will have two 3/8" vacuum lines going into it and a plug ended cable. Very simple to replace.

May 16, 2011 | 2000 Ford Taurus

1 Answer

Location of the pc valve? Best way to get to it? 2000 Taurus with AC.


good luck, do it when it is cold, the hose runs behind the intake to the left side into a black gromet becareful not to rip the hose going into the pcv vave it is a pain to replace

Mar 31, 2011 | 2000 Ford Taurus

2 Answers

Code P1506, 2002 ford taurus wagpn


P1506 Idle Air Control
Overspeed Error

IAC Valve--Bad
Vacuum Leaks
IAC Stuck Open
Failed EAVP System

Disconnect the valve--if little
or no change in RPM,then
Valve is stuck or bad

Mar 16, 2011 | 2000 Ford Taurus

2 Answers

I have a 2000 Ford Taurus that has no heat. The heater core and thermostate have been replaced yet the air blowing from my vents is cold.


Please check your control valve it is operates on vaccum to pull the valve open,and it will before your heater core, most likey it will be under the dash,

Aug 26, 2009 | 2000 Ford Taurus

1 Answer

2000 ford taurus low end ac valve


please rate as fixed if this helps you.

The low pressure service gauge port valve is located on the evaporator to accumulator/drier suction line.


The evaporator to accumulator/drier suction line contains low pressure refrigerant gas and is equipped with a serviceable low pressure A/C charge valve port.

Apr 28, 2009 | 2000 Ford Taurus

1 Answer

Heater Control Valve 2000 Taurus SE


Taurus doesn't have what is called a heater control valve,are you reffering to the remote climate control module,the one that the vacuum lines hook to? If so it is behind the glove box. Just open the glove box and press the 2 clips on the sides so it opens all the way up and it will be located right behind this.

Jan 28, 2009 | 2000 Ford Taurus

2 Answers

2000 Ford Taurus-- Heater not working.


what you need to do is check that your relays are OK
in some cars you cannot see through the relay like a fuse
the only way to check if it is the relays is by replacing them
if this dose not work and you have a electronic climate control system your controm box may be burnt out this will need replacing

Dec 27, 2008 | 2000 Ford Taurus

1 Answer

How to remove the valve cover to replace gasket


What kind of engine? If it's a 3.0L Vulcan, you have to take off the upper and lower intake manifolds and you'll be able to take the valve covers off. There's a bunch to take off before you get to that point. The EGR Valve, Throttle body assembly, ignition coil pack, etc. Make sure you relieve the fuel system pressure (it might be behind the right side well cover of your trunk- disconnect that connection), and take off the negative battery terminal before begining work.

Nov 29, 2008 | 2000 Ford Taurus

Not finding what you are looking for?
2000 Ford Taurus Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...