Question about Mitsubishi Galant

1 Answer

On my mitstishi galant vr4 i have got the tlc light flashing and the ayc light on my dash?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 184 Answers

Sometimes sensor faults which we can cover if simple checks find nothing.
Being 4wd,it is sensitive to wheel sizes or rapid slip and wheel spin.Check to ensure all wheels are same:have you fitted a spare wheel or changed 2 tyres to a different profile?Remove each wheel and check that the sensors bolted to each hub are secure,clean and undamaged,same for the wiring.Also check for damage of the sensor rings on the cv joints.If all ok it is good to get the fault codes downloaded by a garage that can do this,or there are some cheap DIY trouble code readers available.I hope this helps or get back with your findings or codes and I can better diagnose for you.
Fault codes usually can't be erased by removing battery cable for a minute,but you could try this.Code readers can erase though.

Posted on Mar 31, 2011

Testimonial: "your right cos just had 2 new front tyres put on but it was doing it a bit b4 aswell thanks"


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My tlc off light has come on along with my engine light,and when on boost there is a missfire?legnum vr4.

If you can drive it to autozone and have them check the engine codes with a reader, it would be a big help

Dec 19, 2013 | Mitsubishi Galant Cars & Trucks

1 Answer

Cv joint on 98 vr4 galant wont come off

Use a prybar to remove the CV joint, place against hosing and gently pry to release CV.
This is assuming you have un bolted the necessary front end parts prior to removing the CV joint.

Jan 21, 2013 | Mitsubishi Cars & Trucks

1 Answer

My reverse lights are not working in my 97 vr4 galant

Hi there, I am not a mechanic, but there should be a switch by your gearbox close to where you put it in reverse that closes the circuit for the lights to burn when you put it in reverse. Hope it helps.

Aug 07, 2012 | 1996 Mitsubishi Galant

1 Answer

1996 mitsubishi legnum vr4 ayc warning light showing on dash? not on when starting the car but with in few seconds when driving it comes on. what could be possible problems and is it ok to drive it like...

i have the same problem with mine, for some reason my oil lines keep snapping off where they bolt into the diff,

the red ayc light is there to show you theres a problem and it has shut off the ayc, i would look for any oil leaks along the two lines that go from the diff to the pump, and make sure there is oil in the filler tank in the boot,

failing this, have it plugged into a diagnostic computer to find out which error codes are being displayed and what they mean

Feb 13, 2011 | Mitsubishi Galant Cars & Trucks

1 Answer

Hi there im experiancing boost loos, after i have

check all of your couplers and vacuum hoses, then check your boost controller if you have a manual one

Apr 03, 2010 | 1990 Mitsubishi Galant

2 Answers

What is most common problem with legnum vr4

i have a 98 vr4 legunm .theres power to every thing but no firer ,would it be the starta motor,

Mar 10, 2010 | 1997 Mitsubishi Galant

1 Answer

Mitsubishi evo/vr4 idle fluctuating between

Galant VR4 or Evo. which car is it?

have you reset the ecu? disconnect the battery for 5 minutes. make sure you have any radio codes if your radio has a security code lock.

Also could be the idle control stepper. Mitsu gives it some name like ICU but it's a small mottor attached to the throttle that opens and closes valves to let a little more air in and up the rpm.if it's sticky try cleaning the throttle and the valves.

May 05, 2009 | 1988 Mitsubishi Galant

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides