Question about 2001 Mitsubishi Eclipse Spyder

1 Answer

Heater fan works on high only. This is after a mouse built a neat in the fan.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 17,129 Answers

It is possible that the mouse had bitten on the wires and so have taken off the low and mid speed connections. It is better to look inside to see if this is the case , if so reconnect to establish contact.
Also check if the switch is faulty or the motor windings have failed.

Posted on Mar 31, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes heater blower to barely work on high? wont work at all on low


A couple of possibilities; air path blocked by debris (mouse nest, etc.), the sleeve-type phosphor-bronze fan bearings are clogged with wear particles, less likely but still possible is a failing blower switch, failing ground for the fan motor or an oxidized fuse or fuse holder.

A multimeter would be handy to isolate the source of the problem.

With your headlights on and shining on a vertical flat surface, try noticing if they dim very briefly when you quickly turn the blower on.
If not, then the fan isn't getting full current, if they do, then this would indicate a bearing problem with the fan.
Good luck-

Jan 09, 2015 | 2001 Isuzu Trooper

1 Answer

Ac/heater will only work on low when you move it to med or high it shuts off


need to check switch,resistor and fan ---ur switch might have resistor built in it would need to be tested for continuity for the other speeds --if your truck [didnt specify which ] has a separate resistor it should be attached to the heater fan motor housing again resistor needs to be tested -also test ur fan for any resistance or overheating

Apr 10, 2014 | 1993 Toyota Pickup

1 Answer

Blower motor works only on hight speed


Most heater fans have a resister built into the wiring and connection block on the actual casing. High fan speed=full voltage, Mid speed=small resister, Slow fan speed=large resister. Change the resister block. Pete

Sep 30, 2013 | 1998 Chevrolet Malibu

2 Answers

Heater/ac fan only works on high


Hello, pretty easy fix for this. replace the blower resistor assembly mounted under the passenger side of dash the resistor is held in place with 5.5 mm screws

Dec 02, 2011 | 2005 Chevrolet Colorado

2 Answers

98 jetta tdi heater fan runs on high only.


needs a new reostat ,whever it is as some are seperate but some are built in to blower motor housing

Dec 21, 2010 | 1997 Volkswagen Jetta

1 Answer

2005 chrysler 300 heater fan is making noise


yes it is. most heater fans on chrysler products are real easy.you might find a dead mouse or mouse nest in there throwing fan off balance

May 08, 2010 | 2005 Chrysler 300

1 Answer

Why does my heater in my 2000 ford ranger only work on the high setting?


I assume that you are talking about the heater fan?

Your heater FAN has at least 3 settings, and for our purposes we will assume low,med and high

Low and medium run through a resistor High is wired direct
Either your resistor is bad or your fan is
I know it seems wrong that the fan could be shot but it could be pulling so many amps that it won't work in any other mode than high
I just had this happen on one of my trucks
Start with the fan

Apr 06, 2010 | 1998 Ford Ranger SuperCab

2 Answers

Heater fan noise-'02 Nissan Maxima


Had same problem. Replace Blower Motor. Over a 100 dollars at local parts store, but found online for half price. About 30 minutes to replace. http://www.rockauto.com/catalog/raframecatalog.php?carcode=1431961&parttype=6916
6 screws to remove glove box, One plastic nut on kick panel and 3 screws hold the blower to the air box.

Jan 28, 2009 | 2002 Nissan Maxima

1 Answer

No heat


check your coolant level.
If it is fine.. you may have a mouse house built in the fan... the nest blocks the fan blades and causes the fan motor to become unballanced and over worked...
remove the fan/blower motor assembly and clean it out. That should fix ya.

Nov 18, 2008 | 1994 Plymouth Voyager

1 Answer

Heater.cooling fan


It's under the glove box by your feet. Should just be three screws and it will fall right out.

Jun 10, 2008 | 1996 Honda Accord

Not finding what you are looking for?
2001 Mitsubishi Eclipse Spyder Logo

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...