Question about 1999 Honda Accord

1 Answer

Diagram for 99' Accord front brake pads? Is it pads in the back also, or discs?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

Pad

Posted on Mar 31, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size bolt holds the brake and caliper on a 99 Volkswagon Passat


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Mar 27, 2011 | 1999 Volkswagen Passat

1 Answer

Front disc brake assembly diagram


SECTION 206-03: Front Disc Brake 1999 Escort/Tracer Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 06/06/1998 Front Disc Brake Front Disc Brake System Components
Item Part Number Description 1 1125 Front Disc Brake Rotor 2 2B296 Disc Brake Caliper Locating Pin 3 2B120 Disc Brake Caliper 4 2001 Brake Pads 5 - Copper Washers (2 Req'd) 6 - Banjo Bolt 7 2078 Front Brake Hose 8 2W303 Brake Caliper Bolt- (2 Req'd) 9 2814 Brake Hose Clip The front disc brake system consists of a single-piston front disc brake caliper (2B120) and a ventilated front disc brake rotor (1125). The brake shoes and linings (2001) are held in the front disc brake caliper by two front disc brake caliper locating pins (2B296) and two springs. The inboard brake shoe and lining is equipped with a wear indicator that makes a squealing noise when the brake shoes and linings are worn beyond recommended use.

2010&c18=modelyear&c20=n41287&c35=wsm%2cfront%20disc%20brake%2csxf%2c206-03%2cdescription%20and%20operation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=428&ct=lan&hp=n&[aqe] ddll111_28.gif

Dec 15, 2010 | 1999 Mercury Tracer

1 Answer

I'm trying to replace rear brake pads on a 2002 Accord. Where can I get an exploded diagram of the assembly? Having trouble getting them apart.


i can help you and give you step by step instructions. please tell me if you have disc brakes or drum.

besure to include a copy or your problem
mega_muzik@yahoo.com

Oct 24, 2009 | 2002 Honda Accord

1 Answer

98 honda accord makes a popping noise on front driver side


check your disc pad they maybe worn out already. then check the disc plate also.

May 10, 2009 | 1998 Honda Accord

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

1 Answer

Replace front brake pad 2003 toyota 4 runner


Diagram is unnecessry.
Pull both front wheels
Work one at a time leaving the other for reference
Find the retention spring ... its a paperclip thickness wire spring... dislodge center retention loop and undo from both ends which engage brake pad retention rods.
Pull the rods out
Pull the old pads out... laying everything on the ground
Use scrap wooden wedges to pry between the rotor and the caliper ...inside and out until the calipers are fully withdrawn. Use the new pads to measure if they are far enough back.
Note... the brake fluid will have dropped in the master cylinder over many months of wear... do not fill it. When the calipers are pushed back they will fill the reservoir again... one wheel at a time.
Be sure to identify the correct pad based on what you took out and what is on the other side (if you screwed up the layout)
Make sure to take the old antisqueek backing plate from the old pad and place it on the new pad. They don't use lubricant on these anymore.
Replace the pads... the retention rods... then the retention spring
Do the other side
Then progressively step on the brake peddle until full tension is felt
Check the master cylinder reservoir... probably needs no additional fluid.
New pads will register in existing ridges in each disc in no time at all.
You should check the discs to see if they need to be replaced during this operation...using some calipers

Mar 19, 2009 | 2003 Toyota 4Runner

1 Answer

1999 honda accord ex v6


The back brakes on my Honda Accord are disc brakes. After removing the brake cylinder assembly you will see the brake cylinder piston end has a slot in it. The short pin on the back side of the inner brake pad fits into this slot, but also it is used to 'Turn' (clock-wise) the piston back into the cylinder so you fit the assembly back over the new 'thicker' pads. You can not 'press' this piston back into the cylinder.

Nov 30, 2008 | 1999 Honda Accord

2 Answers

Honda Accord 2003 V6 Premature brake replacement


Those models had very soft pads because customers were whining about brake squeaks. Honda's answer was to put on soft pads that wear out quickly. DUH!
If you can find some by VGX- they work great and are quiet also.
Good luck!

Nov 20, 2008 | 2003 Honda Accord

1 Answer

Thumping noise when apply brakes 1990 Accord


yes my cv axles had to be replace cause of the same thing but when you replace one side you need to do the other side at the same time cause when 1 goes bad the other is not that far behind . i know from experience

Nov 18, 2008 | 1990 Honda Accord

1 Answer

Brake pad change for 99 daewoo nubira cdx


I also have a 99 nubira, you should be able to do it with out a book...............they have disc all round and the general set up is the same front and back, If i remember rightly, wheel off, unbolt caliper from mount ( 2 bolts on back face ) pads simply pull off from bottom of mount, refit new pads ensuring same shape on as one that came off. open bonnet and take off cap to brake fluid, using suitable tool ( i used a large screw driver ) push both pistons back into rubber gaitor ( keeping a eye on level in brake fluid, as it will possibly overflow ). You should then be able to refit caliper back to mount. refit bolts, mop up any overflow and replace cap.........JOB DONE :) ........................remember, before you go out onto the road start the car and pump the foot brake a few times until the pedal goes firm again.

Hope this helps you. steve

Jun 19, 2008 | 1999 Daewoo Nubira

Not finding what you are looking for?
1999 Honda Accord Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...