Question about Jeep Cherokee

1 Answer

It was working but now it's not. I would like to know where it is located exactly so that I may see if it's unplugged or dirty, and eventually change it myself.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 324 Answers

Need more details... WHAT is not working? Please give as much information as possible so we can help you!

Posted on Mar 31, 2011

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the Nissan Xterra 2005 Speed Sensor Located and what does the main speed senor look like?

could be the vehicle speed sensor (VSS) and is on the trabsmission
talk with an accredited auto specialist to get the exact location or get a workshop manual to see how to test /replace it
could be very possible wiring problem and dirty connectors in the harness

Jul 15, 2017 | Nissan Cars & Trucks

1 Answer

2000 Lincoln LS hesitates and eventually stalls out

If the check engine light is on than the are trouble codes. I wouldmsuspect there is a lean or rich code. I would unplug the MAF sensor and take it for a drive. If the symptom improves on the test drive replace the MAF sensor.

Sep 02, 2012 | Lincoln LS Cars & Trucks

1 Answer

Main beam flasher stopped working but main bwam still works what is wrong

Its likly the flasher control unit .Im not sure exactly ware its located on a Suzuki but most are eighter pluged into the fuse box or in whats called a relay center under the dask . its round maybe matlic or plastic and usely has to blade pronges that simply just unplugs and you plug the new unit in. If you want to know for sure if its bad unplug it make sure are unpluging the right one because usely 2 of them but 1 emergance flasher but its usely the same part # .So see if the emerg flashers work and switch it with the turn signal flasher and see if they work if so replace the bad unit there about 10 dollars

Mar 04, 2012 | Suzuki Wagon Cars & Trucks

2 Answers

Check engive light on and terrible feul milage

One of the most common causes for your issue is a faulty, or dirty MAF, ( mass air flow ), sensor.
Without knowing your year and model, this is a best guess.

If the MAF is causing this it's easy to check. All you have to do is unplug it to see if it helps your fuel efficiency.

Here a picture of a mass air flow sensor, it's not your engine, but one similar to help you know what you're looking for.

If you find that this your problem, you need to replace it soon, ( within a few weeks ), otherwise you may cause damage to other emission parts and eventually the catalytic converter.

I hope this helps you!
Thanks, Donnie


Mar 09, 2011 | Dodge Grand Caravan Cars & Trucks

1 Answer

What doe's code P0171 mean

The error code P0171 means oxygen sensor in bank 1 detected a lean condition (too much oxygen in the exhaust). This causes because as follows:---
  • The MAF (Mass Air Flow) Sensor is dirty or faulty.
  • There could be a vacuum leak downstream of the MAF sensor.
  • ---------
  • In the vast majority of cases, simply cleaning the MAF sensor does the trick.
  • Inspect all vacuum and PCV hoses, replace if necessary
  • Check for a dirty fuel filter and proper fuel pressure.
  • ---------
  • The MAF is located in the air intake duct work, to the left of the air filter. Look for 2 wires leading to the sensor unit from the outside to pinpoint it's exact location in the housing/duct.
This will help.Thanks.Helpmech

Nov 13, 2010 | 2001 Ford Taurus

1 Answer

Horn on 2006 taurus stop working yesterday - fuse is OK - what else could it be?

Check the connection at the horn. It could be dirty, lose or corroded. There may be a relay for it somewhere.
I don't where the horn is located, usually up front around the grill.
If you are handy, try unplugging the horn and run a jumper wire from the battery to the horn and see if it honks. I don't know if your horn grounds by the mount or of you need to run a pos and neg to it.

Sep 18, 2010 | 2006 Ford Taurus

1 Answer

Location of speed sensor for 1998 silverado

You need to know which one to replace. They are located on the front wheel bearing hub assembly on the backside, by the brake caliper. It is held in place by one screw and the wire just unplugs. Rocks damage these and they quit. Hope this helps.

Jun 11, 2010 | 1999 Chevrolet Silverado 1500

4 Answers

My SRS light comes on and off. I don't know what

It has to do with your airbags. Supplemental Restraint System. This light can be caused by a lot of things including any of the following:
  • Letting battery drain too low
  • Bad Sensor
  • Blown fuse
  • Unplugging the car’s battery
  • Removing the gauge cluster/installing aftermarket gauges
  • G-Force sensors that are under each of the front fenders ($250.00 each)
  • Bad clockspring (located inside your steering wheel)
  • Bad ECU
  • Bad reverse light switch on transmission
  • Car was in an accident
  • Airbag defective/unplugged

Nov 06, 2009 | 2003 Mitsubishi Lancer

2 Answers

How do can I change spark plugs?

hi hillardgarne,

1. Purchase a wrench for spark plugs
2. pull the tension wires from engine.
3. insert the wrench until wrench gets a grip of spark plug
4. turn until plugs are completely loose
5. do this for the rest of the plugs
6. replace old with new plugs.
7. do the same thing but now, you tighten the plug (like screws)
8. return the tension wires


* remember to know exactly the correct location of each tension wires, return to it's exact location (length of wires will help)
* as you take out old plugs, cover the hole where plugs are placed for it not to get dirty.
* in replacing, make sure that plugs are tightly inserted (not to tight though)

hope it helps.

Jul 27, 2008 | 2004 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides