Question about BMW X5 Series

1 Answer

Complete computer system and flashers not working

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 78 Answers

Check fuses

Posted on Mar 30, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right blinker not working 1999 Buick park avenue


You'll need to find a wiring diagram an component location chart to check this out . Here is a diagnostic flow chart for trouble shooting this problem ! Do you know how to use a voltmeter ?
DEFINITION: This table diagnoses inoperative turn signals on one side. It assumes that the cornering lamps, hazard lamps, and turn signals on the other side all operate properly.

1

Did you perform the Exterior Lights System Check?
--
Go to Step 2 - yes
Go to Exterior Lights System Check - no

2

  1. Disconnect the turn signal flasher connector.
  2. Turn the ignition switch to the RUN position.
  3. Place the turn signal switch in the appropriate position.
  4. Connect a DMM from the appropriate turn signal flasher connector cavity to ground:
?€¢
LH: cavity C (ORN)


?€¢
RH: cavity B (BLK)

Is the voltage within the specified range?
10-15 V
Go to Step 3 yes
Go to Step 5 no

3

Connect a fused jumper between the appropriate turn signal flasher connector cavities:
?€¢
LH: cavity C (ORN) to cavity D (YEL)


?€¢
RH: cavity B (BLK) to cavity F (TAN)

Do the appropriate turn lamps light without flashing?
--
Go to Step 4 yes
Go to Step 6 no

4

Replace the turn signal flasher. Refer to Hazard and Turn Signal Flasher Replacement .
Is the repair complete?
--
Go to Exterior Lights System Check
--

5

Repair the open in the appropriate circuit:
?€¢
LH: CKT 57 (ORN) between S200 and the turn signal flasher


?€¢
RH: CKT 58 (BLK) between S201 and the turn signal flasher

Refer to Wiring Repairs in Wiring Systems.
Is the repair complete?
--
Go to Exterior Lights System Check
--

6

Repair the open in the appropriate circuit between the turn signal flasher and the IP fuse block:
?€¢
LH: CKT 685 (YEL)


?€¢
RH: CKT 686 (TAN)

Refer to Wiring Repairs in Wiring Systems.
Is the repair complete?
--
Go to Exterior Lights System Check

May 09, 2015 | 1999 Buick Park Avenue Ultra

1 Answer

Why are there no turn signal or emergency flashers?


What make model an year vehicle do you have ? Could have a control module involved , BCM - body control module , or smart junction box . Computer systems on automobiles have worked there way into everything !

May 05, 2015 | Cars & Trucks

2 Answers

What would cause my blinkers to stop working on a 2000 jeep cherokee sport?


Interesting, these are on the same circuit.

1) Click the hazards on and off a few times to exercise the switch.
2) Replace the flasher timer relay.
3) I believe that this system has a little computer center, about the size of a machbox and it is located under the dash. Swap this out with one from a junkyard.

May 22, 2014 | 2000 Jeep Cherokee

1 Answer

2000 GMC Jimmy, Sigal flasher clicks away when no in the on position,signals seem to work ok when requested,when stepping on brake it seems to get more rapid at times..do i need a new flasher?


try taking out the flasher relay and putting dioelctric grease on connections this may help it will not solve problem completely. I have the same issue

Feb 16, 2013 | 2000 GMC Jimmy

1 Answer

The blinkers only work some of the time. All bulbs are good and the emergency flashers work. I found the flasher for the blinkers, but if it is bad, will the blinkers work some of the time and other times...


you need a signal flasher to correct the problem.flashers will act this way some times when they have an internal problem with the bi-metallic strip that actually completes the circuit and makes the clicking sound.make sure you have found the signal flasher and not the hazard flasher as they look the same.with the hazard flashers on you can see what the signal flasher will look like and it is in the fuse panel.

Mar 25, 2011 | 1987 Ford Taurus

2 Answers

Turn signals aren't working but flashers are


that is because they run off different systems, they both have thier own relays, normally the common fault with flashers not working is either, fuse, or relay (flasher repeter unit), if you turn your turn signals left or right can you hear a click click click noise? if not its your flasher unit, hope this helps

Feb 01, 2010 | 1994 Chevrolet S-10 Blazer

1 Answer

When you first start the car, the turn signals will work for 2 to 3 seconds and then completely stop blinking. The emergency flasher does work a bit longer;but then stops..


I had a similar problem on a 2001 Cherokee I once owned. The left side blinker would stop working after a few seconds, but the right side worked perfectly. I replaced the flasher and that solved the problem. I don't know why they did that since they share the same flasher. There is also a flasher on the emergency lights as well. It's a cheap and simple fix if that is the problem. Give it a shot.

Dec 13, 2009 | Jeep Cherokee Cars & Trucks

1 Answer

Emergency Flashers totally out, Rear lights malfunctioning


Check the ground on the passenger side rear lights, it's likely bad. As for the hazards, sounds like a bad flasher or fuse.

Sep 03, 2009 | Ford Super Duty Cars & Trucks

1 Answer

Flashers not working


pull the fuse panel cover and the cover will show you where the correct fuse is.

Does the emergency (four way) flasher system work?

Make sure the four way flashers are OFF , as the turn signal indication lamp system will not work with the four ways ON.

Dec 03, 2008 | 1998 Ford Taurus

1 Answer

Override remote


I have a similar type of problem. After charging the battery and re-setting the computer, the front and rear lights that would be on in the drving light mode, now are somehow connected to a flasher unit and continue to flash even when the key is off. The only way I've found to stop the lights flashing is to pull the green fuse in the computer box. Looks forward to learning how to fix.

Jun 27, 2008 | 1997 Subaru Legacy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...