Question about Ford Mustang

1 Answer

What wires do i tap into - Mustang Ford Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 504 Answers

Need more info

Posted on Mar 30, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2000 s500 Mercedes Benz i try to tap into my radio for power with a aftermarket radio and loss all power air unit alarm not working fan running high

The yellow wire is for memory on the radio. You have to tap into a key on power source for the on/off button on the radio. Sounds like you may have messed up other components by tapping into a data wire. You can unhook the battery for about 30 minutes and see if they reset. If not, you most likely have to replace them. Send 12 volts to the wire wire and you can burn up many other computers.

Nov 01, 2015 | Cars & Trucks

1 Answer

Locating wiring for reverse

the easy way is to tap into the reverse rear white tail light wiring RUDY PEREZ.

Oct 10, 2014 | Cars & Trucks

1 Answer

Where to tap 12v switched in the dash?

There should be the power wire to the stereo that you can tap into. Red not yellow. Yellow is constant power and red is power when the key is on.

May 21, 2014 | GMC Sierra 2500HD Cars & Trucks

1 Answer

How do i tap into a 2011 buick enclave dome light to add led lights under the dash. I want them to turn on when the dome light goes on. Where would I find the positive wire for those lights

The easiest place for you to tap the Dome light power would be at teh fuse panel where the fuse is located. The ground for that to work is the little switch in teh door jam near the hinges. The problem you may run into is the dome light coming on when you activate the switch to turn those LED lights on. Your going to tap the power wire direct and put the switch to turn them on controlling the ground unless you want them to work at the same time the dome light does in which case I would tap the power line direct and then run an additional wire to tap the switch in the door. A better option, at least to me, would be to tap power off the lighter circuit and control that with the switch then you could ground anywhere you have a good ground.

Oct 27, 2010 | 2009 Buick Enclave

1 Answer

I need to wire in plow lights and i need to know what wires to tap into ?

You can tap right into your headlight wire, keep in mind high and low beams use a test light to find out what is what.

Sep 27, 2009 | 1995 Dodge Dakota

2 Answers

I have a 1996 Toyota Tercel with an aftermarket alarm system that I'm uninstalling. There are two large gauge wires from the ignition bundle, black/yellow & white/red that have taps on them. A third...

something is obviously wrong with the wiring try reinstalling the old system and letting a n experienced mechanic install this other one for you wiring is everything

Sep 06, 2009 | 1996 Toyota Tercel

1 Answer

Where can I safely tap 12v power to add another circuit?

Check the ignition wires with a test light and locate the wire that goes on and off with the key turned
Auto part stores sell an adaptive positive battery cable connector tap off this with #12 wire to one side of a 30A relay tap the other side (load) this goes to your device then: tap off the other side of the relay (switch) cut the wire to the ignition feed; then back to the ignition switch use #18 wire with either wirenuts or, crimp connectors for this and, don't forget to ground ask the auto parts person to show you the "load" side (your device" and, the "switch" side of the relay.

Apr 21, 2009 | Chevrolet Suburban 1500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides