Question about 1999 Chevrolet S-10 Pickup

1 Answer

Need to replace ignition tumblers etc. on a 1999 chevy s10 pick-up. need to see picture or diagram if possible.

Posted by on

  • mdiane70 Apr 08, 2011

    already had the new lock cylinder, but lost keys to old one, needed to get old one out and didnt know how without the old key.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

Go to advance or autozone and buy a whole new lock cylinder assembly. much simpler

Posted on Mar 30, 2011

  • mdiane70 Apr 08, 2011

    I already have the new lock cylinder but dont have key for the old one, my problem was not knowing how to remove it without the key to turn it to the on position.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 chevy s10 4x4 4.3 pickup truck I am changing the ignition switch the key does not have a chip so will I need to have it re programmed


I would suggest that you only change the barrel of the ignition switch in which case the locksmith doing the job will be able to reset the tumblers to your existing key thereby overcoming a reprogram problem

Oct 10, 2015 | Cars & Trucks

1 Answer

Throttle housing diagram for 1996 Chevy S10. 4 cylinder pick up truck


Sorry I have the tech to send diagrams .
However I do have the factory manual for this engine .
Why don't you send some more information and likely I can solve your problem

Mar 14, 2015 | Chevrolet S 10 Cars & Trucks

1 Answer

Wiring diagram for the ignition switch on a 2000 chevy s10 ?


Unfortunately, you will not be able to do that. The key and tumbler are an intricate part of the vehicles "anti-theft system. If the ignition switch or tumbler is broken it will have to be replaced and the theft code relearned. When the key is turned in the tumbler, the switch reads the key code and sends the code to the BCM. The BCM verifies the code is correct and sends a start message to the ECM and allows the engine to start. With out that code verification, the engine will not start.

Aug 28, 2014 | 2000 Chevrolet S-10

1 Answer

Ignition switch diagram


IF you have a locksmith take it out it is possible that he may be able to repair the pins in the tumbler but I think the cost would be more than getting a new tumbler. If you use a locksmith then he can set the new tumbler pins so that you can use the old key and that will save you carrying extra keys unnecessarily.

Dec 30, 2013 | Dodge Cars & Trucks

2 Answers

My 1999 chevy malibu key will not turn in the ignition


you need a new ignition switch, or the key is slightly bent or to worn down to hit tumblers

Mar 14, 2012 | 1999 Chevrolet Malibu

1 Answer

Need torque specs for 1999 chevy s10 blazer rear differential bearing caps 4wd 4.3


still looking for you answer but i found this useful bit of info to add to you knowledge complete with specs, diagrams and drawings and pictures for all s10 models. http://h-body.org/dave/Build%20a%20Better%2010-bolt%20H-body%20Rear%20End.htm

Oct 24, 2010 | 1999 Chevrolet Blazer

1 Answer

My anti theft alarm goes off and makes it to where I can't start my car how do i bypass this


You can't do it; the Theft System it's integrated to the vehicle control computer ECU/PCM; you need install one INTERFACE to make this work.

Review this Wiring Diagram and this comment: when installing a 791 TRANSPONDER BYPASS System on this vehicle it will be necessary to remove the BOTTOM STEERING COLUMN Cover and IGNITION SWITCH TUMBLER to gan access to the Factory Transponder System around the Ignition Switch. To do so will require that you first look at the bottom of the STEERING COLUMN COVER to identify the screw holes from the IGNITION SWITCH TUMBLER RELEASE PIN HOLE, that is required to remove the Ignition Switch Tumbler, the IGNITION SWITCH RELEASE PIN HOLE is the SMALLEST Hole in the plastic cover in this picture. NOTE *** to remove the IGNITION SWITCH TUMBLER, a TORX #15 Bit on a Screw Driver will work just fine. Incert it up into this hole and press, at the same time, turning the IGNITION SWITCH ON and the Tumbler will pull out at the same time. This Must be done to remove the IGNITION SWITCH TUMBLER so that the BOTTOM Steering Column Cover can be removed to gain access to the TRANSPONDER SYSTEM built around the IGNITION SWITCH.

Also, its possible that you need other details from the Taurus's Owners Manual.

Hope helps.

Jun 01, 2010 | 1996 Ford Taurus

2 Answers

Cant get key switch out of housing, on a 1974 chevy pick up.Trere are no screws or clips visible.


If you mean remove the ignition tumbler from the steering column, you will have to remove the steering wheel and lock plate, then you will need to remove the turn signal lever and screws, and then pull the turn signal switch up and out of the way, you should then be able to see the housing for the ignition tumbler down in the steering column. Look at the tumbler housing and there should be a small slot towards the end of the housing that you can put a small standard screwdriver into and depress a locking latch that is built into the tumbler. When this latch is depressed you will be able to pull the ignition tumbler straight out of the column.

Apr 19, 2010 | 1986 Chevrolet Chevy

1 Answer

I have 98 Chevy S10 pick-ups? MY problem is there


Yes it could well possibly be the ignition switch or starter solenoid or intermittent ignition switch starter contact.Again check connections on battery especially the ground connection at the block.Also there could be air in the fuel line any of these could be hindering start up!

Oct 02, 2009 | 1998 Chevrolet S-10 Pickup

3 Answers

I have a 97 Chevy S10 pickup...cannot move shifter out of park


When my battery was dead i was forcing the key in the ignition which messed everything up with my chevy s10 and have to get everything replaced....: (

Dec 28, 2008 | 1997 Chevrolet S-10 Pickup

Not finding what you are looking for?
1999 Chevrolet S-10 Pickup Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...