Question about 1999 Suzuki Esteem

1 Answer

Studs i need to replace lug studs i was told to remove axels if i have to how do i go about it

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 232 Answers

GO TO AUTOZONE.COM AND U CAN IT INFORMATION ON WHAT NEEDS TO BE DONE

Posted on Aug 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have broken lugs on my 2004 Hyundia Santa Fe. I am trying to pull the front left hub off using a puller (3 jaw). The puller is pushing the axel back. I called the local dealer. The Mechanic said I...


You should be able to hammer out the wheel studs
if you have clearance
You shouldn't have to pull the entire bearing assy

Look on YOU TUBE there are all kinds
of videos of hub replacements

You remove the axle nut & 3 or 4 bolts
holding the bearing assy,that is all
The axle stays in place
There is no puller involved

Mar 10, 2011 | Hyundai Santa Fe Cars & Trucks

1 Answer

I am wanting to replace the rear wheel studs that are broken. The wheel hub flange won't come off. Is there a special puller for this, do I need to apply more force or is there another method for removal?


You do not remove the wheel hub flange, just follow the procedure that I replied to earlier, and this is the procedure if you do not want to obtain a special tool for pressing the lug studs;

First you will have to pound the broken lug studs out of the wheel hub, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down to take up the slack.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Jun 13, 2010 | 2003 Chrysler Town & Country

2 Answers

Broken lug nut how to replace lug nut studs


take off tire. remove old stud by hammering it out with a punch. put a socket behind axle plate so as not to break the plate. when replacing, just start stud from back by hand, then use a lug nut to pull it in tight. when tight replace tire!

Apr 14, 2010 | 1999 Oldsmobile Intrigue

2 Answers

How do i remove the front hub on my 1999 accord so i can replace the lug stud


Some hubs have a sweet spot to change the studs If not you'll have to press out the bearing by removing the tie rod,ball joint, axel, strut and breaks then take the hub to someone with a press.

Feb 03, 2010 | 1999 Honda Accord

1 Answer

Does the wheel barring have to be replaced when the stud is broke


If you use a hammer to drive the broken stud out you can cause damage to the bearing.
If you use a wheel stud press, the hub bearing will not be affected. The press will remove the old stud and install the new one.
Good luck.
Regards,

Aug 18, 2009 | Honda Civic Cars & Trucks

1 Answer

Have broken studs on the front passenger side and need to know how to replace.


I assume that you are referring to the wheel studs and if so you will have to remove the wheel, the brake caliper, the brake caliper stand and the brake rotor. Drive the old stud out with a hammer. Make sure you purchase new lug nuts with the studs. If they are the acorn style, buy one that is not to help with installation. Slide the new stud in the hole from the rear of the flange, install some washers for clearance of the stud shoulder. Install the non acorn style lug nut on the stud backwards. Using a impact gun, pull the stud through. Remove the backwards lug nut and washers.

Jul 26, 2009 | 1989 Nissan Maxima

1 Answer

1990 Sentra How it remove and replace lug studs on front wheel


there is a large nut that holds that hub on. Remove the cotter pin and the cap from the bolt... remove the bolt and the hub comes off.

Robert

Feb 27, 2009 | 1990 Nissan Sentra

1 Answer

Lug studs


Which wheels front or rear?

Aug 04, 2008 | 1999 Suzuki Esteem

Not finding what you are looking for?
1999 Suzuki Esteem Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...