Question about 1998 GMC Sierra

1 Answer

Over heating and low oil pressure 2004 gmc 3500 savanna

Posted by on

  • stringbean69 Jan 11, 2009

    over heating and low oil pressure



1 Answer

Change oil pump it only cost $100 most like thats the problem

Posted on Aug 19, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

On my 2004 gmc Sierra dually it reads low oil pressure when I press the brakes. Once I release them the buzzer goes off

Flush the oil put a detergent in to the engine add oil flush again and change the sensor for the oil pressure

Nov 30, 2014 | 2004 GMC Sierra

1 Answer

Fuel filter location

Try this link
It may be this same location as the one on this youtube

Jul 23, 2014 | GMC Savana Cars & Trucks

1 Answer

2000 GMC Savanna, oil pressure guage drops to

You need to pull the pressure sensor and install a manual test gage, (borrow from Autozone or other chain part store) that is the only way to verify the engine is not loosing oil pressure.

Oct 30, 2017 | 2000 GMC Savana

1 Answer

My 2004 gmc envoy is giving me ans oil pressure low warning and then shutting off my engine

It needs to have the oil pressure manually tested with a mechanical pressure guage. If good oil pressure is found, you most likely have a bad sending unit.

Oct 02, 2012 | 2004 GMC Envoy

1 Answer

Where is the ac lowside port located on a 2005 gmc savanna van

The low side port of the 2005 GMC savanna Van is located on the low pressure side of the compressor.

This is found by locating the compressor driven by a belt that has a clutch that engages and disengages as the a/c cycles.

The low pressure piping is always in the larger diameter piping, and the high pressure side is always contained in the smaller diameter piping.

Therefore, follow the thick pipes from the compressor up to the accumulator, which looks like a large can of soup. On the accumulator receiver/drier is a port that connects to the tube that is connected to the can of r134a freon refrigerant.

Simply quick connect the tube to the low side port, which is located on the 'thick' tubing or on the accumulator and then fill until the low side pressure is 25 psi to 45 psi while the compressor is running.

When the car is off and the compressor is not running, the pressure should be 75 psi to 100 psi on a hot day.

Hopefully the system doesn't have a leak slow or fast in it.

Aug 17, 2010 | 2005 GMC Savana

1 Answer

I am changing the front brakes pads and on a 2004 3500 series gmc

Not really, some basic tools, metric sockets and wrenches, screw drivers and a 6" C clamp to compress the caliper piston.
The most important thing to remember is to make certain the caliper pins are clean and greased when you reassemble. If you are replacing components such as rotors or calipers, make sure you replace the parts in pairs. Make sure no grease or contaminants are on the rotors or brake pads.
Good luck.
You can go to to get detailed instructions for replacing your pads.

Nov 25, 2009 | 2004 GMC Savana

Not finding what you are looking for?
1998 GMC Sierra Logo

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides