Question about Ford F-100

Open Question

Replacing starter in 1974 F100 Camper Special. Header & starter unbolted. Cannot get either one out of engine compartment

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ktlivinseren
  • 2 Answers

SOURCE: I have a 1998 4Runner

i have the same runner and when i changed my starter twice!!! buy new its the only way to go,,,,laying under the vehicle looking up you will see a bracket coming of the exhaust i loosend the bracket and was able to get it out that way,,,not much room you will have to do some wiggling bets of luck

Kevin in vancouver

Posted on Aug 12, 2008

  • 1071 Answers

SOURCE: starter installation

hold engine up with jack stand and unbolt trns lines where they are held to trans they should move enought to remove starter

Posted on Jul 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change fuel filter on a Ford f100 1974


Ford used several types of fuel filters in 1974 depending on the engine and where it was sold. One type was at the inlet of the carburetor.
Another was a can at the bottom of the fuel pump:
myu6e9ggandhtialz0trbyw.jpg

Jan 30, 2015 | Ford Cars & Trucks

1 Answer

Can I fit 1974 f100 differentials and front suspension on a 1974 f250?


Given the age of the trucks there should be old paper manuals and parts lists about where you can compare axle ratios, drive shafts, suspension parts etc. Try ebay. Would it not be easier to get another F250 front end?

Nov 04, 2014 | Ford Cars & Trucks

1 Answer

How to remove starter on hyundai sonata 2011


Disconnect battery cable at battery, be sure it is positioned to not contact any metal within engine compartment while disconnected. Disconnect all wiring at starter, usually two wires, one slightly larger than the other. Unbolt and remove starter. China OBD2 car diagnostic tools wholesale on CareUCar

May 07, 2014 | Cars & Trucks

1 Answer

Where can i find a vacuum diagram for a 1974 pontiac ventura V8 5.7L 2bbl carb?


Typically, vacuum diagrams are located on a sticker in the engine compartment or on the under side of the hood. Sometimes they are even in the owners manuals of older vehicles. If none of the above are present, try an internet search. Most automotive information databases like Alldata & Shopkey don't go always go back as far as 1974 but it may be worth a try. You could also try using the make and model of your carb on a 350 engine in a later year vehicle as those engines are so common.

Apr 23, 2014 | 1972 Pontiac Ventura

2 Answers

Where is the starter located in the 1991 Chevy Lumina APV ??


97de1d4.gif


REMOVAL AND INSTALLATION
3.1L Engine
Besides regular hand tools, a special oil pressure sensor socket will be necessary to complete this operation.

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the A/C compressor brace (if equipped).
  4. Extract the wiring harness from the retainer and position it out of the way.
  5. Remove the cover from the starter wiring.
  6. Remove the outer nut and disengage the wiring from the starter solenoid.
  7. Disconnect the electrical connector from the oil pressure gauge sensor.
  8. Using the special socket, remove the oil pressure gauge sensor.
  9. Unbolt the starter from the engine. Retain any shims.

To install:
  1. Install the starter to the engine, reuse any shims that were removed. Tighten to 32 ft. lbs. (43 Nm).
  2. Connect the wiring to the solenoid and install the outer nut.
  3. Place the cover over the starter wiring.
  4. Replace the oil pressure gauge sensor using the special socket.
  5. Plug the electrical connector onto the sensor.
  6. Mount the harness to the retainer.
  7. Install the A/C compressor brace (if equipped).
  8. Lower the vehicle.
  9. Connect the negative battery cable.

Oct 08, 2010 | 1991 Chevrolet Lumina Apv

1 Answer

Need a diagram to take a starter off.


You dont really need a diagram. Starter sits on the driver's side(LHD) of the engine towards the lower rear of the engine compartment.
Disconnect the ( - ) of the battery.
There are 2 wires on the starter, one lugged - can be pulled off, the other needs a 13mm(0.5 inch) wrench.
Then there are 2 bolts that hold the starter to the engine. (14 mm if I'm not mistaken) Unbolt and out it comes!

Jun 22, 2010 | 1994 Isuzu Trooper

1 Answer

Starter installation


hold engine up with jack stand and unbolt trns lines where they are held to trans they should move enought to remove starter

Jul 19, 2009 | 1991 Volkswagen Jetta

4 Answers

1976 VW Van Battery


The battery should be under the front passenger seat. Move the seat forward as far as it will go, and you'll see a metal plate (may be under the carpet), which comes off with four Phillips screws. To actually get the battery out, you will need to remove the seat.

Aug 05, 2008 | 1986 Volkswagen Wagon Camper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...