Question about Ford Probe

1 Answer

Removed oil pan and tried to remove thelower engine block reinforcement section to get to pistons took out bolts but it still wont come off

Posted by on

Ad

1 Answer

That's not how it is done

Remove the engine, so you can
work on it

Posted on Mar 28, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove oil pan



4x4
1. Open the hood.
2. Disconnect the battery negative cables.
3. Remove the intake air assembly.
4. Remove the radiator shroud retaining bolts.
5. Install engine support fixture # 8534B .
6. Raise and support the vehicle.

WARNING: HOT OIL CAN CAUSE PERSONAL INJURY.


7. Drain the engine oil (Refer to 09 - Engine/Lubrication/OIL - Standard Procedure) .
8. Loosen the front engine mount bolts.
9. Lower the vehicle.
10. Use the engine support fixture # 8534B to raise engine out of the front mounts.
11. Remove the engine oil dipstick.
12. Raise and support the vehicle.
13. Remove oil pan bolts, break the pan to block seal, and lower pan slightly and remove oil suction tube fasteners.
14. Remove oil pan and suction tube.
15. Remove the 2 bolts from the front of the engine block stiffener.
16. Remove the oil pan.


4x2
1. Open the hood.
2. Remove the negative battery cables.
3. Raise and support the vehicle.
4. Remove the transmission oil cooler lines.
5. Remove the propeller shaft.
6. Remove the starter bolts.
7. Support the starter.
8. Remove the torque converter bolts.
9. Remove the exhaust hanger bolts.
10. Remove the gear shift cable.
11. Remove the wiring harness.
12. Remove the transmission mount.
13. Remove the crossover bolts.
14. Position the transmission jack.
15. Remove the bell housing bolts.
16. Remove the transmission.
17. Remove the flywheel housing bolts (8).
18. Remove the flex plate bolts (8).
19. Remove the engine oil dip stick.
20. Drain the oil.
21. Remove the steering rack bolts.
22. Remove the oil pan bolts.
23. Remove the oil pickup bolts.
24. Remove the oil pan. user_online.gif

Aug 01, 2014 | Dodge Ram 3500 Cars & Trucks

1 Answer

How to change oil pan on 2001 x5 bmw 3.0


remove the reinforcement plate under the engine. 4 x 17mm nuts. You will need to hold the back side of each bolt with a box end wrench or it will just spin. Then you will see the oil pan. Remove the 10mm nuts and the pan will come off. . (Drain the oil first!). When you replace the reinforcement plate, use new bolts. They are one-time use. (Really).

Jul 11, 2014 | 2001 BMW X5 3.0

1 Answer

Change oil pan on a 2001 sonoma


the 2.2 engine and the 4.3 engine with 2WD MODEL you have to remove engine.the 4WD MODELS, you have to remove all these parts first remove dip stick, drive belt, splash shield, remove front axle shield and the transfer case shield, front skid plate and the flywheel cover,remove left and right engine mount through bolts.then raise the engine using a lifting device, and block in position,using large wooden blocks between the motor mounts and brackets.you will also need to remove these parts,remove disconnect oil cooler line, remove pitman aem bolt and pitman arm, remove idler arm bolts and idler arm, remove front differential through bolts,remove front driveshaft if necessary,remove differential assembly by rolling it forward for clearance, remove starter motor, then remove oil pan bolts then remove oil pan, your oil pan need to be flushed slightly forward of rear of the block to allow proper alignment with the transmission housing.using feeler gauge measure the 3 oil pan to transmission contact points.clearance should not exceed 0.011 in. 0.3mm if so realign the oil pan.oil pan bolts torque is 18 ft lbs tighten oil pan bolts in sequence.

Aug 25, 2012 | Cars & Trucks

2 Answers

When changing the oil pan on a 2006 town & country do you have tighten the bolts in a sequence?



Removal & Installation

2.4L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
  4. Clean the oil pan and all gasket mating surfaces.

To install:
  1. Install or connect the following:

    Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
  2. Fill the crankcase to the correct level.
  3. Start the engine, check for leaks and repair if necessary.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
  4. Clean the oil pan and all gasket mating surfaces.

To install:
  1. Install or connect the following:

    Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
  2. Fill the crankcase to the correct level.
  3. Start the engine, check for leaks and repair if necessary.

3.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Starter motor Front motor mount bracket Bending braces Torque converter dust shield Oil pan

    0996b43f8020961b.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Oil pan mounting bolt tightening sequence-3.0L engine


To install:
  1. Clean the oil pan all mating surfaces.
  2. Apply RTV gasket material to the oil pan.
  3. Install or connect the following:

    Oil pan. Tighten the bolts in sequence to 50 inch lbs. (6 Nm). Torque converter dust shield Bending braces Front motor mount bracket Starter motor Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

3.3L & 3.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:
  1. Clean the oil pan and all mating surfaces.
  2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
  3. Install or connect the following:

    New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:
  1. Clean the oil pan and all mating surfaces.
  2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
  3. Install or connect the following:

    New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

May 05, 2012 | 2006 Chrysler Town & Country

1 Answer

Oil pan repl. 1995 ford ranger 3 liter automatic


Oil Pan, Ranger SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Engine Lifting Sling 014-00036
Removal
  1. Disconnect battery ground cable. For additional information, refer to Section 14-01.
  1. Remove air cleaner outlet tube assembly by unclipping air cleaner clamp, loosening hose clamp at outlet tube, disconnecting intake air temperature (IAT) sensor and mass air flow (MAF) sensor connectors, and crankcase ventilation hose.
  1. Remove oil level indicator fan shroud retaining bolts. Position shroud over fan blade.
  1. Remove radiator support bolts. Raise and secure radiator to front core support.
  1. Remove engine mount nuts from studs.
  1. Unclip 42-pin connector from bracket and position it aside.
  1. Install suitable lifting brackets to left and right exhaust manifolds. Attach Rotunda Engine Lifting Sling 014-00036 (or equivalent) to lifting brackets. With a suitable lifting device raise engine approximately 50.8 mm (2 in). Install wood blocks between engine mounts and support brackets. Remove lifting device.
  1. Raise vehicle on hoist. For additional information, refer to Section 00-02.
  1. Drain the oil.
  1. Remove transmission insulator retaining nuts and install a jack stand to extension housing. Raise transmission about 25.4-101.6mm (1-4 in) to gain access for removal of oil pan.
  1. Remove transmission inspection cover.
  1. Remove starter motor splash shield.
  1. Remove starter motor retaining bolts and secure starter aside.
  1. If equipped, disconnect and remove low oil level sensor.
  1. NOTE: Oil pan fits tightly between transmission spacer plate and oil pump pickup tube. Use care when removing pan to avoid damaging either part.
    Remove oil pan bolts and lower pan.
  1. Remove oil pump retaining bolts. Lower and twist pump to allow the oil pan to lower completely. Remove the pump and pan assembly from vehicle.
  1. Remove and discard oil pan gasket.
  1. Clean the oil pan mating surface.
Installation
  1. NOTE: When using silicone rubber sealer, assembly should occur within 15 minutes after sealer application. After this time, the sealer may start to set up, and its sealing effectiveness could be reduced.
    Apply a 4.0-6.0 mm (1/5 inch) bead of Silicone Rubber D6AZ-19562-AA or -BA (or equivalent meeting Ford specifications ESB-M4G92-A and ESE-M4G195-A) to junction of rear main bearing cap and cylinder block and to junction of front cover assembly and cylinder block. Position oil pan gasket to cylinder block and secure it with Gasket and Trim Adhesive D7AZ-19B508-B (or equivalent meeting Ford specifications ESR-M11P17-A and ESE-M2G52-A).
  1. Install oil pump assembly and bolt. Tighten bolt to 40-55 Nm (30-40 lb-ft).
  1. NOTE: If oil pan is replaced with a new pan you must tighten new pan to spec then loosen and retighten.
    Position oil pan to cylinder block and install oil pan to engine bolts. Tighten bolts to 10-14 Nm (7-10 lb-ft).
  1. Remove jack stand and install transmission insulator retaining nuts. Tighten nuts to 85-118 Nm (63-87 lb-ft).
  1. NOTE: When replacing low oil level sensor, use a new metal gasket with a rubber O-ring.
    Install low oil level sensor. Tighten sensor to 20-34 Nm (15-25 lb-ft).
  1. Install transmission inspection cover and retaining bolts. Tighten bolts to 10-14 Nm (7-10 lb-ft).
  1. Install starter motor and bolts. Tighten bolts to 22-28 Nm (17-20 lb-ft).
  1. Securely install starter motor splash shield.
  1. Lower vehicle.
  1. Install lifting device and support engine. Remove wood blocks and lower engine back into original position. Remove lifting device and Rotunda Engine Lifting Sling 014-00036 (or equivalent). Remove lifting brackets from right and left exhaust manifolds.
  1. Remove support straps, lower radiator into position, and install radiator bolts to core support. Position fan shroud and install the retaining bolts. Tighten bolts to 6-8 Nm (52-71 lb-in).
  1. Install engine mount nuts and tighten to 98-132 Nm (72-97 lb-ft).
  1. Connect 42-pin connector to the bracket and install oil level indicator.
  1. Install engine air cleaner outlet tube assembly. Connect IAT sensor, MAF sensor, and crankcase ventilation hose. Securely tighten the hose clamp.
  1. NOTE: When battery has been disconnected and reconnected, some abnormal drive symptoms can occur while powertrain control module (PCM) (12A650) relearns its adaptive strategy. Vehicle may need to be driven 16 km (10 miles) or more to relearn strategy.
    Connect battery ground cable.
  1. Fill crankcase with correct viscosity and amount of engine oil.
  1. Start engine and check for oil leaks.

    Oil Pan Installation - Ranger


    a10121g.gif


    Hope this helps

Aug 14, 2011 | 1995 Ford Ranger Supercab

2 Answers

I HAVE A 2007 2500 DODGE RAM WITH 5.9 CUMMINS AND AUTOMATIC. CAN I LOOSEN THE MOTOR MOUNTS AND LIFT THE ENGINE ENOUGH TO REPLACE THE OIL PAN?


depends on whether you have 2WD or 4WD. The manual says if you have 2WD you have to remove the tranny,but not if you have 4WD. See procedures below.

5.9L & 6.7L Diesel Engines
2WD Models

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Open the hood.
  3. Remove the negative battery cables.
  4. Raise and support the vehicle.
  5. Remove the transmission oil cooler lines.
  6. Remove the propeller shaft.
  7. Remove the starter bolts.
  8. Support the starter.
  9. Remove the torque converter bolts.
  10. Remove the exhaust hanger bolts.
  11. Remove the gear shift cable.
  12. Remove the wiring harness.
  13. Remove the transmission mount.
  14. Remove the crossover bolts.
  15. Position the transmission jack.
  16. Remove the bell housing bolts.
  17. Remove the transmission.
  18. Remove the flywheel housing bolts (8).
  19. Remove the flex plate bolts (8).
  20. Remove the engine oil dip stick.
  21. Drain the oil.
  22. Remove the steering rack bolts.
  23. Remove the oil pan bolts.
  24. Remove the oil pickup bolts.
  25. Remove the oil pan.

4WD Models
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Open the hood.
  3. Disconnect the battery negative cables.
  4. Remove the intake air assembly.
  5. Remove the radiator shroud retaining bolts.
  6. Install engine support fixture No. 8534B.
  7. Raise and support the vehicle.
  8. Drain the engine oil.
  9. Loosen the front engine mount bolts.
  10. Lower the vehicle.
  11. Use the engine support fixture No. 8534B to raise engine out of the front mounts.
  12. Remove the engine oil dipstick.
  13. Raise and support the vehicle.
  14. Remove oil pan bolts, break the pan to block seal, and lower pan slightly and remove oil suction tube fasteners.
  15. Remove oil pan and suction tube.
  16. Remove the 2 bolts from the front of the engine block stiffener.
  17. Remove the oil pan.

Oct 30, 2010 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

How to change oil pan gasket for 2005 dodge caravan


Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004

Oil Pan - Removal & Installation

2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
  4. Clean the oil pan and all gasket mating surfaces.
To install:
  1. Install or connect the following:
    Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
  2. Fill the crankcase to the correct level.
  3. Start the engine, check for leaks and repair if necessary.

3.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Starter motor Front motor mount bracket Bending braces Torque converter dust shield Oil pan

    e6c7cfd.jpg
    Fig. Oil pan mounting bolt tightening sequence-3.0L engine

To install:
  1. Clean the oil pan all mating surfaces.
  2. Apply RTV gasket material to the oil pan.
  3. Install or connect the following:
    Oil pan. Tighten the bolts in sequence to 50 inch lbs. (6 Nm). Torque converter dust shield Bending braces Front motor mount bracket Starter motor Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

3.3L & 3.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:
  1. Clean the oil pan and all mating surfaces.
  2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
  3. Install or connect the following:
    New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

Hope helps (remember rated this).

Jun 24, 2010 | 2005 Dodge Caravan

1 Answer

I cracked my oil pan and i need to know if i need to take out my engin to change it i'm low on cash i need help


here's v6 3.8L

Section 03-01A: Engine, 3.8L 1996 Thunderbird, Cougar Workshop Manual
IN-VEHICLE SERVICE Oil Pan/Oil Pump Screen Cover and Tube Removal
  1. Disconnect battery ground cable (14301).
  1. Remove air cleaner outlet tube (9B659). Refer to Section 03-12 .
  1. Remove two bolts retaining radiator upper sight shield (8C291) and position radiator upper sight shield aside.
  1. Remove hood weather seal.
  1. Remove windshield wipers.
  1. Remove LH cowl vent screen and wiper module.
  1. Install Three Bar Engine Support D88L-6000-A or equivalent.
  1. Raise vehicle on a hoist. Refer to Section 00-02 .
  1. Remove front engine support insulator through-bolts.
  1. Partially lower vehicle.
  1. Raise engine and support with Three Bar Engine Support D88L-6000-A or equivalent.
  1. Raise vehicle.
  1. Remove starter motor (11002).
  1. Position drain pan.
  1. Drain engine oil.
  1. Remove oil bypass filter (6714).
  1. Remove starter motor wire, ground strap and automatic transmission oil cooler lines.
  1. Remove oil pan-to-bell housing bolts and bolts at crankshaft position sensor lower shield.
  1. Remove remaining oil pan retaining bolts.
  1. Remove steering shaft pinch bolt and separate steering shaft.
  1. Position transmission jack under front sub-frame (5C145).
  1. Remove six rearward bolts on front sub-frame. Loosen two forward front sub-frame bolts.
  1. Remove lower shock absorber-to-front suspension lower arm bolts and nuts (both sides).
  1. Lower front sub-frame.
  1. Remove oil pan (6675).
  1. Empty any residual oil from oil pan.
  1. Remove oil pump screen cover and tube retainer bolts and support bracket nut. Remove oil pump screen cover and tube (6622) and discard oil pump inlet tube gasket (6626).

Apr 14, 2009 | 1996 Ford Thunderbird LX

1 Answer

Do you have pictures of the parts that need to be removed in order to change the oil pan gasket?


Section 03-01: Engine, 4.6L (4V) 1997 Continental Workshop Manual IN-VEHICLE SERVICE Oil Pan/Oil Pump Screen Cover and Tube Removal
  1. Turn rear suspension leveler compressor switch (5K761) off (located in luggage compartment).
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove oil level dipstick (6750).
  1. Raise vehicle on hoist.
  1. Remove dual converter Y pipe (5F250). Refer to Section 09-00 .
  1. Drain engine oil from crankcase.
  1. Disconnect engine control sensor wiring (12A581) from the low oil level sensor connector.
  1. Remove the power steering pressure hose retainer brackets from the engine front cover studs (two places). Position the power steering pressure hose (3A719) out of the way.
  1. Remove 16 bolts retaining oil pan (6675) to cylinder blocks (6010) and remove oil pan and oil pan gasket (6710).
  1. Remove two bolts retaining oil pump screen cover and tube (6622) to oil pump (6600).
  1. Remove bolt retaining oil pump screen and cover and tube support brace to main bearing stud spacer.
  1. Remove oil pump screen cover and tube. Discard O-ring.

  2. 02d437f.gif

      Item Part Number Description 1 W701240 Bolt (16 Req'd) 2 6675 Oil Pan 3 6622 Oil Pump Screen Cover and Tube 4 6010 Cylinder Blocks 5 6710 Oil Pan Gasket A — Tighten to 20 Nm (14 Lb-Ft), then rotate 60 degrees clockwise
        Installation
        1. Inspect oil pump screen cover and tube and replace if necessary.
        1. Position oil pump screen cover and tube on oil pump with a new O-ring and hand-start two bolts.
        1. Install bolt retaining oil pump screen cover and tube to main bearing stud spacer finger-tight.
        1. Tighten oil pump screen cover and tube-to-oil pump bolts to 8-12 Nm (71-106 lb-in). Tighten oil pump screen cover and tube to main bearing stud spacer bolt to 20-30 Nm (15-22 lb-ft).
        1. Clean oil pan and inspect for damage.
        1. Clean sealing surfaces of engine front cover (6019) and cylinder blocks with a clean cloth. If scraping is required, only use plastic-tipped scrapers to prevent damaging the aluminum sealing surfaces.
        1. Position new oil pan gasket on oil pan.
        1. Apply Silicone Gasket and Sealant F6AZ-19562-AA or equivalent meeting Ford specification WSE-M4G323-A6 where engine front cover meets cylinder blocks and crankshaft rear oil seal retainer meets cylinder blocks. Position oil pan on cylinder blocks and install 16 bolts. Tighten bolts in sequence to 20 Nm (14 lb-ft), then rotate an additional 60 degrees clockwise.

      Apr 03, 2009 | 1997 Lincoln Continental

      Not finding what you are looking for?
      Cars & Trucks Logo

      Related Topics:

      29 people viewed this question

      Ask a Question

      Usually answered in minutes!

      Top Ford Experts

      yadayada
      yadayada

      Level 3 Expert

      76846 Answers

      Colin Stickland
      Colin Stickland

      Level 3 Expert

      22246 Answers

      fordexpert

      Level 3 Expert

      5546 Answers

      Are you a Ford Expert? Answer questions, earn points and help others

      Answer questions

      Manuals & User Guides

      Loading...