Question about 1993 Chrysler New Yorker

Open Question

How do you remove the alternator on a '93 new yorker? The power steering bracket is in the way

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 523 Answers

SOURCE: 2000 dodge caravan remove mounting assembly to

I have changed the pump out on my wife's 99 Voyager, 3.3 liter. Per my manual (and experence) there should be a nut at the back of the pump connecting it to the bracket. Then there are three (3) bolts which connect the pump to the bracket (front of pump under pulley. I my memory serves part of the front bracket will have to be removed with the pump. Lastly, if a 3.3 or 3.8 V6 you;ll have to remove the exhaust where it connects to the back manifold (has a flex pipe to it. Trust me on this the manual is correct with removing the ehaust from the engine, I tried to prove the engineers wrong but its the only way out and back in. Plan for these four (4) bolts to break and replace with new when putting pump back in, use new exhaust gasket too. To remove/install pulley to pump you'll need a special puller, cheap to by or may be rented.

I hope this may have assited you,
Tom

Posted on Jun 09, 2010

dennymulford
  • 1055 Answers

SOURCE: 89 S15 4.3L Need instructions to remove and install pwr steering

i know what bolt your talking about,you canreach it thru the wheel well with an extention!!!
but if your just removing the pump,some of the pullys have three holes in them too get too the pump bolts if not then you need a power steering pump pully remover auto zone loans them out!!!!

Posted on Feb 28, 2009

  • 2 Answers

SOURCE: 1990 new yorker alternator replacement

You are right about removing the motor mount. You have to support the engine with a jack. Use a piece of plywood between the jack and the oil pan. Remove the motor mount and you should be able to lift the engine up about 2-3 inches with the jack. Remove the serpentine belt and then you should have enough room to remove the alternator.

Posted on Jul 02, 2009

  • 4044 Answers

SOURCE: the bracket that holds the alternator and the

You might find one at a Junk Yard or be able to order it from the dealer, that is where I would look for it in that order. As far as how easy it is to replace that will depend on how everything is connected and if the job requires special tools.

Posted on Oct 07, 2009

  • 6982 Answers

SOURCE: 1998 Jeep Grand Cherokee Power Steering Pump/Pulley/Belt

I see this is a two part question...
In replacing the alternator, there is no reason at all to be messing with the pulley on the power steering. That pulley is pressed on and though you could remove it with a puller it is far more difficult to re-install without the proper tools. (it is not hammered on). Power steering pulleys don't just fall off. They are so tightly pressed onto the shaft that they don't even require a retaining bolt to hold them on.
Without the benefit of being able to examine it myself, I'd have to guess that either you originally had a mis-match of pulley to pulley shaft and the pulley was sliding on the shaft (so remote a concept that you may be hit by a meteorite if you buy that) Or someone removed it for an unknown reason and did not properly re-install it.

Posted on Feb 01, 2010

Testimonial: "Thank you thundergod! My daughter has been borrowing my car so I have not been able to examine it myself either. Thanks again for your quick help!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the procedure for removing the power steering pump


1982 Chrysler New Yorker Power Steering Belt Removal ...

? 0:35
www.youtube.com/watch?v=vZD17F_ao-o
Jan 18, 2015 - Uploaded by Kerman 559 Sanchez
1982 Chrysler New Yorker Power Steering Belt Removal ...1990 Chrysler New Yorker Fifth Avenue Start Up, Engine, and In Depth Tour ...

1990 chrysler new yorker 3.3 power steering pump change ...

www.fixya.com/cars/t15056742-1990_chrysler_new_yorker_3_3_power
Nov 18, 2012 - SOURCE: 1990 new yorker alternator replacement. You are right aboutremoving the motor mount. You have to support the engine with a jack.
images for 1990 Chrysler New Yorker remove power

Oct 20, 2015 | 1990 Chrysler New Yorker

1 Answer

How is the power steering brackets attached?


Chrysler used the Chrysler LHS nameplate for the following vehicles:
so what is it? really. sure 14th gen
The New Yorker came standard with the 3.5 L EGJ which produced 214 hp (160 kW)
and guess what engine type dictates bracket types. so what engine.


from the P/S pump to the engine .
you never said what?
the pump or the rack or the searing gear box.
????
all have brackes.
login to
alldata.com
or
why not just use, Chrysler tell you this, on line.
like this, ever seen this , 100 more... like it.
im a mopar guy, (love em)
USA< im USA< are YOU? and if not why not SAY.

http://www.factorychryslerparts.com/productSearch.aspx?&ukey_make=1061&ukey_model=0&modelYear=1994&ukey_category=0&ukey_driveline=0&ukey_trimlevel=0&ukey_modelRange=0&isOnSale=0&searchTerm=

Jun 15, 2014 | 1994 Chrysler LHS

1 Answer

I want to know how to remove the alternator kia optima 2003


  1. Disconnect the negative battery cable.
  2. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  3. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  4. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  5. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  6. Remove the power steering pump, 2.0L engine only.
  7. Remove the power steering pump bracket, 2.0L engine only.
  8. Remove the alternator B terminal cover cap.
  9. Disconnect the alternator electrical connections.
  10. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  11. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  12. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  13. Remove the power steering pump, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  15. Remove the alternator tensioner mounting bolt and the belt tensioner.
  16. Remove the alternator pivot bolt.
  17. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  18. Remove the alternator.

    0996b43f80207fa4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-1.5L and 1.6L (VIN 5) engine shown


    0996b43f80207fa5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-2.0L and 1.6L (VIN 3) engines shown


    0996b43f80231908.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-2.4L and 2.7L engine


To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).

  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).

  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).

  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).

  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.

Feb 09, 2011 | 2003 Kia Optima

1 Answer

How to replace alternator


1990-93 Accord
  1. With the ignition OFF, disconnect the negative battery cable.
  2. Remove the power steering pump. Refer to Section 8 for the complete procedure.
  3. Remove the cruise control actuator but do not disconnect the actuator cable; simply move the unit out of the way with the cable attached.
  4. Unplug the multi-pin electrical connector.
  5. Remove the terminal nut and remove the wire from the terminal.
  6. Loosen the adjusting bolt; remove the alternator nut. Fig. 3: Alternator mounting on 1990-93 Accords 86803003.gif

  7. Remove the belt from the alternator pulley.
  8. Remove the adjusting bolt, the lower through-bolt and the small support stay.
  9. Support the alternator. Remove the upper through-bolt and remove the alternator.
  10. If desired, remove the alternator mounting brackets. To install:
  11. If the alternator brackets were removed, reinstall them. Coat the bolts with a thread sealer or liquid thread lock. Install the bracket bolts and tighten them to 36 ft. lbs. (50 Nm).
  12. Fit the alternator into place. Install the upper through-bolt and tighten it to 33 ft. lbs. (45 Nm).
  13. Install the small stay, the lower through-bolt and the adjusting bolt. Make certain the adjusting bolt is properly installed.
  14. Install the belt. Install the alternator nut. Adjust the belt tension. Tighten the alternator nut to 19 ft. lbs. (26 Nm).
  15. Connect the wire to the terminal and tighten the nut.
  16. Engage the multi-pin connector to the alternator.
  17. Install the cruise control actuator.
  18. Install the power steering pump.
  19. Connect the negative battery cable.
next.gif

Jan 21, 2011 | 1991 Honda Accord

1 Answer

Alternator bracket broke and can not get to last bolt to get it off to have welded. Any suggestions appreciated.


Is this the bracket that has the power steering pump under the alternator? If so the power steering pump has to be removed to remove bracket. To remove power steering pump you have to remove the pump pulley with a special tool and then press it back on with another tool. Both tools can be rented at your local Advanced auto parts store.

Jun 02, 2010 | 1984 Chevrolet Blazer

1 Answer

1992 Dodge Caravan alternator replacement


I have the '93 shop manual which describes how to do it with the 3.3L and I have the Haynes that covers the 3.3/3.8L for '96-99 and they read about the same. Let me give you the one from the '93 Chrysler shop manual:
1.Disconnect the battery.
2. Remove the alternator drive belt
3. Loosen, but do not remove, the nut on the support bracket at the exhaust manifold. (this is on the rear of the engine where the bracket is attached to one of the exhaust manifold studs).
4. Remove the alternator tensioner power steering bracket bolt.
5. Remove the tensioner stud nut and the tensioner.
6. Remove the 2 alternator mounting bolts.
7. Remove and position the power steering reservoir from the alternator mounting bracket. Do not remove the hose from the reservoir.
8. Remove the 3 alternator support bracket bolts.
9. Remove intake plenum-to-alternator mounting bracket bolt
10. Remove alternator support bracket.
11. Position alternator and remove alternator wiring.
12. Remove alternator!
Again this is for the 3.3L and is from the '93 van manual but it appears to apply to the 3.8L as well. Installation is the reverse, tighten the mounting bolts to 40 ft-lbs.

Good luck.

Dec 25, 2009 | 1992 Dodge Caravan

1 Answer

Replacing alternating belt


A good repair manuel to get which has picture step by step, Hanyes auto repair manuel at any aut part store for 20 bucks is a great investment.
.0l Engines The 3.0L engines were equipped with either the Nippondenso or Bosch alternators.
1. Disconnect the negative battery cable.
2. Install a 1/2 in, breaker bar in the tensioner slot. Rotate counter-clock- wise to release belt tension and remove poly-V belt.
3. Remove the alternator mounting bolts (2)
4. Remove the wiring and remove alternator.
To Install:
5. Position the alternator onto the engine, then install the wiring.
6. Set the alternator against the mounting bracket and install the mounting bolts.
7. Rotate the tensioner counterclockwise and install poly-V belt.
8. Connect the negative battery cable. 3.3L and 3.8L Engines
The 3.3L and 3.8L engines were equipped with the Nippondenso alternators. 1. Disconnect the negative battery cable.
2. Remove the alternator drive belt, by relieving the tension on the dynamic tensioner
3. Loosen the nut on the support bracket at the exhaust manifold, do not remove it.
4. Remove the alternator tensioner/power steering bracket bolt.
5. Remove the tensioner stud nut and remove the tensioner.
6. Remove the alternator mounting bolts.
7. Remove the power steering reservoir from the mounting bracket, do not disconnect the hoses, and position it out of the way.
8. Remove the alternator support bracket bolts, Remove the intake plenum to alternator bracket bolt and remove the alternator support bracket from the engine.
9. Remove the alternator from the engine and disconnect the electrical leads.
To Install:
10. Install the alternator in position on the engine and connect the electrical leads.
11. Install the alternator support bracket, tighten the retaining bolts to 40 ft. lbs. (54 Nm). Install the power steering reservoir on the mounting bracket.
13. Install the alternator mounting bolts, tighten the bolts to 40 ft. lbs. (54 Nm).
14. Install the tensioner and tensioner mounting stud. Install the retaining nut on the exhaust manifold.
15. Install the alternator belt, insert a 1/2 in. extension into the square hole in the tensioner and turn the tensioner. Tighten the tensioner bolt.
16. Connect the negative battery cable.

Oct 09, 2009 | 1994 Dodge Caravan

1 Answer

How to check alternator, and how to replace it.



Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  4. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  5. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  6. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  7. Remove the power steering pump, 2.0L engine only.
  8. Remove the power steering pump bracket, 2.0L engine only.
  9. Remove the alternator B terminal cover cap.
  10. Disconnect the alternator electrical connections.
  11. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  12. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  13. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump, 1.6L (VIN 3) engine only.
  15. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  16. Remove the alternator tensioner mounting bolt and the belt tensioner.
  17. Remove the alternator pivot bolt.
  18. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  19. Remove the alternator.

    0900c15280028419.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-1.5L and 1.6L (VIN 5) engine shown


    0900c1528002841a.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-2.0L and 1.6L (VIN 3) engines shown


    0900c1528002841b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-2.4L and 2.7L engine

To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).

  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).

  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).

  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).

  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.

Jul 29, 2009 | 2002 Kia Spectra

1 Answer

Steering pump on 93 Chrysler New Yorker Salon


make sure the lines are not crossed and also check the condition of the drivebelt first

Feb 11, 2009 | 1993 Chrysler New Yorker

1 Answer

Changing the starter on a Kia Spectra


Here's step-by-step instructions on how to access, remove and re-install your alternator. Hope it helps! Have a great day!

Alternator Kia_Sephia_Rio_Spectra_Optima_1998-2006
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  4. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  5. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  6. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  7. Remove the power steering pump, 2.0L engine only.
  8. Remove the power steering pump bracket, 2.0L engine only.
  9. Remove the alternator B terminal cover cap.
  10. Disconnect the alternator electrical connections.
  11. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  12. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  13. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump, 1.6L (VIN 3) engine only.
  15. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  16. Remove the alternator tensioner mounting bolt and the belt tensioner.
  17. Remove the alternator pivot bolt.
  18. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  19. Remove the alternator. 0900c15280028419.jpgAlternator mounting—1.5L and 1.6L (VIN 5) engine shown 0900c1528002841a.jpgAlternator mounting—2.0L and 1.6L (VIN 3) engines shown 0900c1528002841b.jpgAlternator mounting—2.4L and 2.7L engine
To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).
  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).
  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).
  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).
  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.
 

Nov 23, 2008 | 2003 Kia Spectra

Not finding what you are looking for?
1993 Chrysler New Yorker Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...