Question about Buick LeSabre

1 Answer


Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 90 Answers

Autozone offers the free use of a tool called a steering wheel puller specifically for this circumstance.

Posted on Mar 28, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Unlock steering wheel & ignition cyclinder to replace it with new one

double posted backup one (i gave 3 choices there)
define cant. (cant figure)
or the anti-theft bolts confusing you , the FSM covers all that
why not read that first. then ask questions.

to make cars not easy to seal they make it like this,
90 to now.
it needs to be removed the whole assembly.
anti theft bolts,off, , assmbly off, may take steering wheel off too.
the hand to lock smith (just did a 91) and he
uses special smith drift pins to drive the hidden (backside away from thieves, internal lock pin, he tumbler comes out or he drills it out.
then a new pin, and holding new tumbler, and then test it , ok ,
the reversses all above.
the fsm covers this all step by step, why must you avoid books.
or read

Oct 18, 2014 | 1994 Toyota Camry

1 Answer

Durango can't turn ignition

First thing make sure it isnt just the steering wheel lock, move the steering wheel back and forth while trying to turn key. I that doesnt work it is most likely the key and tumbler. Over time it is normal to experience wear. The solution is to replace the key and tumbler in the steering column.

Nov 17, 2012 | Cars & Trucks

1 Answer

How to remove the ignition in 1991 GMC Sierra when the position is in "off"? I can't turn the key to the "on" position as instructed

with the steering wheel removed remove the KEY CHIME(push in connector w/2 copper wires)
there should be a bolt securing key & tumbler removing bolt & pull tumbler out

Jun 13, 2011 | GMC Sierra 1500 Cars & Trucks

1 Answer

Do i have to remove the steering wheel to change the ignition switch on a 2002 cavalier

Ignition switch located half way down steering column.
Ignition tumbler (Where you insert the key) Need to remove steering wheel, if tilt steering need remove c clip, then there is a hex bolt securing the tumbler.
Ignition switch is a bit more involved.
hope this helps, James Booth

May 17, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

Key stuck in ignition -- cannot turn on or off. Can an ignition switch cause the tumbler to lock up? Or does the ignition tumbler need to be replaced? If the ignition tumbler needs to be replaced, how...

lets start simple.get a can of silacone spray oil and spray into the switch and keep moving key and you will find this will reliese the key,if you need to remove the ign switch dont panic as its a simple enough job.Forget about steering wheel and whatever,simply remove the outer plastic cover then this exposes the switch at the back of switch is a plug with wires pull it away ,then below the key you should see a tiny screw undo, and make sure the steering lock is not under pressure,ie steering wheel free,when trying to remove switch move steering wheel back/forward and switch should pull out.good luck.adrian,,,,

Nov 25, 2010 | 1988 Chevrolet Celebrity

1 Answer

How do you remove the ignition switch on a ford 250 1994 model?

Do you mean the key and tumbler, or the switch down on the bottom of the steering column? If you mean the switch, just lower your steering column by removing the cover at the bottom of the dash, and then remove the 2 bolts on either side of the column. The switch is near the base of the column, and the rod that runs from the ignition switch goes into it.
If you mean the key and tumbler, you have to pull the steering wheel, remove the screws from the signal cam, and then remove the locking bolt that holds the tumbler. You will need a steering wheel puller to remove the snap ring, and to reinstall.

Sep 04, 2010 | 1994 Ford F250 Supercab

1 Answer

I bought a 76 k5 blazer but there is no key for it how do u change the locking cylinder or what every you call it

You have to pull the steering wheel and components. Once you get down to the signal light cam, you take the screws out of it, lift it up and you will see the bolt that holds the tumbler in. Remove it, and your key and tumbler will come out. You will need a steering wheel puller.

May 02, 2010 | Chevrolet Blazer Cars & Trucks

2 Answers

03 chevy monte carlo can't turn key

Tumblers are going bad. Get a locksmith or dealer to replace.

Apr 15, 2010 | 2003 Chevrolet Monte Carlo

2 Answers

1992 gmc ignation tumbler

You have to remove the steering wheel, and the turnsignal switch, and you will see a torx bolt that retains the tumbler.

May 12, 2009 | 1996 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides