Question about 1994 Volkswagen Jetta

1 Answer

I have a 1995 Jetta with a 1994 2.0 engine and transmission. It is an automatic. There is one wiring hookup on the 1995 harness that the 1994 transmission does not have an input on the housing for. It causes the transmission to not shift automatically. What is it for and what can I do to fix this?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 829 Answers

This is a problem,the 95 model has a 01m transmission and the 94 has an 096.Even though they look very similar the wiring and computer controls are very different.They will not intercahnge.You will need to use the 95 model wiring harnes,transmission ,and computer but I am not sure this will work with the 94 model engine.

Posted on Mar 28, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crank shaft positing sensor hookup in the wiring harness of a 94 dodge ram 360


It is hard to get to - the sensor is at the back of the engine mounted through the transmission bell housing. The connector should be within 6 to 8 inches from the sensor. The sensor reads a sensor ring on the flywheel/flexplate.

Jan 31, 2015 | 1994 Dodge Ram

1 Answer

Can a 1994 nissan altima wiring harness ,engine and trans fit a 1995 nissan altima


Engine will, not sure about the harness. You can swap parts off the old engine.

Jul 02, 2011 | 1995 Nissan Altima

2 Answers

How to check transmission fluid level


Most 1995-on VW models don't have a transmission fluid dipstick for checking the transmission fluid level. To fill and check the level of the VW automatic transmission fluid you have to remove a plug on the side or bottom (location depends on model and if you have an automatic vs. manual transmission) of the transmission drain pan. The factory manual refers the expensive VAG 1924 special tool for pumping the VW automatic transmission fluid into the oil pan.

Mar 02, 2011 | 2002 Volkswagen Jetta TDI

1 Answer

I want to install an LT 1 engine taken from a 1994 chevy z 28 with a 6 speed automatic transmission.into my 1992 corvette which also has a LT1 engine with a six speed automatic. what would be the...


The wiring harness will be completely different as well as the engine mounting locations. The computer will also need to be from an LT1 Camaro.

Nov 16, 2010 | 1992 Chevrolet Corvette

2 Answers

Where is transmission solenoid located on 1995 vw jetta !!!!


Inside the transmission case above the pan. You should probably let a transmission mechanic handle this one.

Jul 24, 2009 | 1995 Volkswagen Jetta

2 Answers

Just had ac repairs done on 1994 Mercedes 500SL. After I picked it up from shop, the ASR system is active, and by the time I got it home, the CHECK ENGINE light is on, too. Any suggestions?


turn off car and unscrew the throttle cable a little bit then start it up again. ASR is finicky if it feels pedal is being depressed on startup it goes into "limp home" mode.
Have you had your engine upper and lower wiring harness replaced? From 1991-1995 MB was forced to use a biodegradable insulation that went bad under the hood due to engine heat.

Jun 08, 2009 | 2003 Volkswagen Jetta TDI

1 Answer

Wiring harness


I dont think so. 95 had 2 different engines. it will be close. you will have to check every connection and it will take some time. id get the correct one for your model and year and it still might be a little different.

Dec 18, 2008 | 1995 Honda Accord

1 Answer

Engine


Yes, a c220 engine will fit, but you will also have to use the ECM and wiring harness from the c220

Nov 06, 2008 | 1994 Mercedes-Benz C-Class

1 Answer

Won't Start


My daughters car did the exact same thing. Lights and all. I replaced the pump twice and both relays (auto shut down and fuel pump relay). Very frustrating indeed.

The 1994 recall (see below) is right on! Right behind the engine block intake (the long aluminum block on top) is a tie rod that connects from the rack and pinion to the wheel. On top of the tie rod is a bundle of wires that are wrapped in cloth style tape, just resting on the rod. As the vehicle is driven, the steering rod will rub the wires (as the wheels are turned) thus causing a possible short. My daughters was. I used liquid tape, wrapped in tape and used zip ties to lift off the rod. I have driven it alot and have not had an incident yet!

FEB 08, 1994 | Recall ID# 12389 Hide Details
Recall Reason ELECTRICAL SYSTEM:WIRING
Recall Date FEB 08, 1994
Model Affected INTREPID
Potential Units Affected 110000

Recall Summary
THE RIGHT STEERING TIE ROD CAN RUB THROUGH THE AUTOMATIC TRANSMISSION WIRING HARNESS CAUSING A SHORT CIRCUIT WHICH RESULTS IN ELECTRICAL SYSTEM MALFUNCTIONS INCLUDING ENGINE STALLING AND AN INOPERATIVE PARK/STARTER INTERLOCK SYSTEM.

Consequence
ELECTRICAL SYSTEM MALFUNCTION CAUSING STALLING WHILE IN MOTION OR AN INOPERATIVE PARK/STARTER INTERLOCK SYSTEM, WHICH ALLOWS ENGINE START WHILE THE TRANSMISSION IS NOT IN THE PARK POSITION, MAY RESULT IN AN ACCIDENT.

Remedy (see above)
INSTALL A REVISED WIRING HARNESS BRACKET AND A PLASTIC CONVOLUTED SLEEVE TO PROTECT THE TRANSMISSION WIRING HARNESS.

Notes
CHRYSLER CORPORATION

Aug 10, 2008 | 1995 Dodge Intrepid

1 Answer

Removaul of engine


you do not need to take it apart, just disconect the wires from the engine.
dont foret to hook the cluch cable in via that white clip.

Jul 05, 2008 | 1995 Volkswagen Jetta

Not finding what you are looking for?
1994 Volkswagen Jetta Logo

Related Topics:

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...