Question about 2001 Volkswagen Golf

1 Answer

How do I remove the rear wheel bearing from my golf chico without a bearing puller?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

You don't remove it without one.

Posted on Mar 28, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the Tata indica rear wheel bearing have a collapsable washer between the two bearings


Tata Indica LSi 1.4 RHD model. First time working on an Indian brand car. This one has rear brake linings or shoes as they are also known as. I used the method someone mentioned here to remive the hub after I couldnt get it out. But the other side I battled then realised I had a huge enough 3 legged pully puller which came in handy. As mentioned remove the wheel then the cap for the bearing followed by the 24mm nut and big flat locating washer. Then fit the wheel back on to the hub with the other parts removed and fit the 24mm nut on to the shaft but just the tip. Use the 3legged puller to tighten up against the nut which will then pull the wheel, drum and wheel bearing off the car. Simple as that. No need for pulling the wheel back and forth with force to remove it. You wont get it off if one bearing is sitting on tight. Cheers

Jun 18, 2012 | Tata Indica Cars & Trucks

1 Answer

How do u fasten rear wheel bearings without a talk wrench Golf mk1 1.4i 2008 mod sport


Over tightening of wheel bearings will destroy them, or the hub if the bearing locks and spins.


Torque (yup that's it) wrenches aren't expensive, and good to have. Buy one and use it.

May 25, 2012 | 2008 Volkswagen Golf 1.9

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

How do you change the rear wheel bearings on a 2004 chevy express 1500 van?


Axle Shaft Bearing & Seal Removal & Installation To Remove:
  1. Raise and safely support the vehicle.
  2. Remove the axle shaft.
  3. If replacing only the seal, remove the seal using a suitable seal removal tool.
  4. If replacing the seal and bearing on the 8.6 inch axle, install the slide hammer and adapter behind the bearing and pull out the bearing and seal together.
  5. If replacing the rear axle shaft seal and the bearing on the 9.75 inch axle, install the J 29712 or equivalent bearing puller into the axle housing behind the axle bearing.
  6. Remove the axle shaft seal and the bearing by tightening the nut on the J 29712 bearing puller.
Use a slide hammer, bearing puller and adapter to remove the old axle bearing 88457g81.gif

To Install:
  1. Install the axle shaft bearing using a suitable size driver. Drive the bearing into the housing until the tool bottoms against the tube.
  2. Lubricate the seal lip and install the seal with a suitable seal driver. Make sure the seal is fully seated in the axle tube.
  3. Install the axle shaft.
  4. Fill the rear axle with the correct lubricant.
  5. Lower the vehicle.
prev.gif next.gif

Oct 18, 2010 | 2004 Chevrolet Express

1 Answer

Squeeky rear wheel bearing. How is it removed and replaced?


This is a rear wheel drive vehicle? Are you sure it's not a brake squeal?
The bearing sits in the end of the axle tube and is lubed with the differential fluid. You need to dissasemble the differential to remove the axle, to remove the bearing. You need a puller for that type of bearing.

Sep 08, 2009 | 1994 Chevrolet Caprice Classic

2 Answers

I have a 1997 Citi Chico white. Boot leak!


I had the same problem with my 1999 model. Check under the spare wheel, there are 3 or 4 round metal pieces welded on, but 1 wasn't welded property.

Sep 08, 2009 | 1997 Volkswagen Golf

3 Answers

Rear wheel bearing shot on a 1994 bmw 318i is this a Diy fix?


Its not so bad - however you will need the proper puller and small race tool (if the bearing separates).

They can be rented at a parts store relatively cheap.

Here is the procedure so you can determine your abilities...


The wheel bearings are only removed if they are worn. They cannot be removed without destroying them (due to side thrust created by the bearing puller). They are not periodically disassembled, repacked and adjusted.
  1. Remove the wheel and support the car. Remove the attaching bolts and remove and suspend the brake caliper, hanging it from the body so as to avoid putting stress on the brake line.
  2. Remove the setscrew with an Allen wrench. Pull off the brake disc and pry off the dust cover with a small prybar.
  3. Using a chisel, knock the tab on the collar nut away from the shaft. Unscrew and discard the nut.
  4. Pull off the bearing with a puller set such as 31 2 101/102/104 and discard it. On the M3, use a puller set such as 31 2 102/105/106. On the M3, install the main bracket of the puller with 3 wheel bolts.
  5. If the inside bearing inner race remains on the stub axle, unbolt and remove the dust guard. Bend back the inner dust guard and pull the inner race off with a special tool capable of getting under the race (BMW 00 7 500 and 33 1 309 or equivalent). Reinstall the dust guard.

To install:
  1. If the dust guard has been removed, install a new one. Install a special tool (BMW 31 2 120 or equivalent; on M3, use 31 2 110 or equivalent) over the stub axle and screw it in for the entire length of the guide sleeve's threads. Press the bearing on.
  2. Reverse the remaining removal procedures to install the disc and caliper. Torque the wheel hub collar nut to 210 ft. lbs. (290 Nm). Lock the collar nut by bending over the tab.

Thanks for using FixYa - a Very Helpful rating is appreciated for answering your FREE question.


Aug 06, 2009 | BMW 318 Cars & Trucks

1 Answer

Front wheel bearing 1986 Golf


Mount the tool on the wishbone and extract wheel bearing. Application example: ...... KL-0215-410 Press Tool Kit VW Golf III without Hydraulic Cylinder

Jun 28, 2009 | 1986 Volkswagen Golf

1 Answer

Rear wheel bearings


if i assume this is a 9 and 1/2 chrysler rearend...take the rear differential cover off..remove the screw tht holds the pin that passes through the spider gears then remove the pin. push the axle shafts inward til the c clips can be removed then slide the shafts out. you will need a bearing puller to remove the bearing and seal

Nov 02, 2008 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
2001 Volkswagen Golf Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...