Question about 1993 Plymouth Acclaim

1 Answer

How do i flush heater core in 1993 acclaim - 1993 Plymouth Acclaim

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 6,674 Answers

Have a look at this tip, it may be of some help to you.
http://www.fixya.com/cars/r3698796-unclog_heater_core_rather_replace

If you need more assistance, get back to me/us.

Posted on Mar 29, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 Nissian D21 truch do not hefat on the inside


Try flushing the hoses out,heater core may be clogged.If it doesn't work then heater core needs replacing.

Feb 28, 2013 | 1993 Nissan Pickup

1 Answer

1993 Mazda very little heat windows fog up bad.


Check the 2 tubes at firewall that lead to the heater core. If they're not getting hot, then the heater core is plugged up and needs to be flushed out or replaced.

Jan 19, 2011 | 1993 Mazda MPV

1 Answer

Little or no heat


Your antifreeze is either low or your heater core is blocking up which would mean a flush or replace. Your thermostat may be stuck open & need replacing. Also with the rad cap off, check to see if you have any flow through the rad when engine is hot,if not replace the water pump. Hope this helps. Good luck!

Jan 02, 2011 | 1993 Plymouth Acclaim

1 Answer

Heater blows cold air, also defrost blows cold


check to see if your hoses to heater core are hot on both sides. my 93 hoses where hot going in the heater core but not out. I flushed the heater core now I have heat

Dec 12, 2010 | 1993 Cadillac DeVille

2 Answers

HOW TO REPLACE HEATER CORE IN 1992 PLYMOUTH ACCLAIM


Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Nov 25, 2010 | 1992 Plymouth Acclaim

1 Answer

Heater blows cold


If no coolant flowing through the heater core then ther is no heat. There are 2 possible root causes needed to check out: 1- THE VALVE TO CONTROL THE COOLANT FLOWING TO THE HEATER CORE IS NOT OPENING AS DESIRED. 2- THE HEATER CORE GOT CLOGGED UP AND NEED TO BE FLUSHED.

Nov 15, 2009 | 1993 Ford Taurus

1 Answer

The engine over heated replaced thermosat and still over heated. by passed the heater core and the engine doesn't over heat now.


SOUND LIKE HEATER COR IS PUGED SO YOU CAN TRY TO REVERS FLUSH IT WITH WATER HOSE CONNECTED TO HEATER HOSE IF THIS DOSE NOT WORK NEW HEATER CORE

Aug 12, 2009 | 1993 Jeep Cherokee Country

1 Answer

1993 subaru impreza L heater is not working


if the engine temp seems normal on the dash gauge then it may be a clogged heater core.have the sysyem flushed-it worked for me recentlythe other options may be a heater door not closing..some are vacuum activated a flush is a good place to start..good luck

Jan 19, 2009 | 1993 Subaru Impreza

Not finding what you are looking for?
1993 Plymouth Acclaim Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...