Question about 2002 Toyota Highlander

Open Question

What size is the axle nut on a 2002 toyota highlander front axe ?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Cant get axle nut off of my 2002 cavalier

use a 34 or 36mm socket

Posted on May 21, 2009

  • 9 Answers

SOURCE: I have a toyota highlander (2002). It came with

Open the remotes up...Are the boards the same...?

Posted on Jun 12, 2009

  • 1 Answer

SOURCE: need the axle nut size for the front drivers side

Our is a 44mm socket size........thought i would post it, since the above was stupid and didn't....can't find one in town.

Posted on Jun 26, 2009

  • 43 Answers

SOURCE: Code error P1135

I usually use Bosch, they are usually a good sensor. The code is for the front/before catalyst A/F ratio.

Posted on Jul 20, 2009

  • 400 Answers

SOURCE: front axle nut size 2003 2500hd

36mm is a little loose but a 35mm will not fit, I use the 36mm all of the time. It's such a heavy nut and stud it will NOT have any effect.

Posted on Oct 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Axle nut size


Requires a 12 point - 30mm socket, you must also punch up the retaining dings to release it.

Jul 22, 2014 | 2008 Toyota Highlander

1 Answer

What size tool/kind of tool do i need to remove the big center star nut on my 2007 toyota highlander front rotor


The rotors are knock off rotors. They are just rusted and stuck to the hub. DO NOT REMOVE THE AXLE NUT. this will not help you get the rotor off. Instead use a large hammer and hit the rotor from the back side. Several good whacks should break it free.

Apr 20, 2014 | 2007 Toyota Highlander Hybrid

1 Answer

Front axle 2002 highlander


to remove front axle.to loosen front axle nut leave vechicle weight on wheel then just loosen front axle nut because axle nut torque at 217 ft lbs torquehard to loose axle nut with vechicle weight off wheel.okay. you need a 1/2 breaker bar and axle socket to loosen axle nut dont use 12 points sockets need go auto parts store buy right socket for axle nut.okay when you loosen front axle nut you need safely raise support vechicle. need to remove wheels remove fender apron seal remove transaxle fluid remove transfercase oil if you have 4WD.remove hub nut remove stabilizer bar link remove speed sensor remove tie rod end remove lower arm from the ball joint then slide the halfshaft from the hub then carefully pry the shaft from the transaxle.then install new front axle push in make sure front axle snap ring on front axle snap in place inside transmission just pull a little on front axle make its in place. when all done tighten front axle much as you can then when done putting every thing back in place.lower vechicle need torque front axle nut to 217 ft lbs.

Jan 12, 2013 | 2002 Toyota Highlander

1 Answer

Front axle nuts size for 2003 pontiac grand prix


2002 Grand Prix front axel nut holding on hub is a 33MM or 1 5/16 deep socket

Feb 08, 2012 | 2003 Pontiac Grand Prix

1 Answer

What type of socket and size do I need to take off


you can go to any advanced auto parts store, and rent a axle nut socket set.. in most cases it a 28 to 36 mm socket.. go to advanced, you will have to pay for the set, but you will get your money back when you return the socket set..good luck keith..

Mar 14, 2009 | 2003 Toyota Highlander

2 Answers

Driver side wiper wont work


One side does not work? Can you move the arm with your hands? If so, look for a loose nut that holds the wiper arm on. Remove the plastic trim on the wiper arm base, and tighten the 12 millimeter bolt. Please advise if this helps.

Dec 22, 2008 | 2003 Toyota Highlander

Not finding what you are looking for?
2002 Toyota Highlander Logo

Related Topics:

371 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...