Question about Jeep Grand Cherokee

1 Answer

Check engine light on, testes found code 1762,1763,0748

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 829 Answers

These codes are circuit codes for the govenor pressure sensor and the solenoid.99 percent of the time a new sensor and solenoid fix this problem.However i have had to replace the connector where the harness plugs into the transmission because of the pins being loose and making bad contact.Let me know if I can help.

Posted on Mar 28, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 sl500 check engine light reset and comes back on after it sits over night. any idea?


What code is it throwing ? Some codes are what are called two trip codes ! You clear the codes an start an drive the vehicle ,no check engine light . Park the vehicle over night an bam next time you start an drive the vehicle the check engine light comes back on .

??There are two types of DTC's, 1 trip DTC's and 2

trip DTC's

??A 1 trip DTC is for a condition that requires

immediate attention such as a catalyst damaging

misfire.

??A 2 Trip DTC is one that a condition must be found

during 2 consecutive trips such as an EGR fault.

??Most Monitors do not set a DTC and light the MIL

when a vehicle fails a test for the first time during a

DRIVE CYCLE. If a test is failed on a second

consecutive DRIVE CYCLE the MIL will light and a

DTC is stored in the vehicles powertrain control
module (PCM).

Feb 07, 2016 | Cars & Trucks

1 Answer

Failed emissions test


First step is to have the code or codes read.If the "check engine light" is on there will be a reason and should be a code or codes to be read.Once you have the codes,you can determine the correction needed to get that "check engine light" out and a valid emissions test completed.Get back to us with the codes found.

Apr 28, 2017 | Saturn Vue Cars & Trucks

1 Answer

2001 ford taurus 3.0 v6 code p0306 misfire


Please go to this page for engine misfire causes.

Aug 08, 2012 | 1997 Ford Taurus

3 Answers

Engine light is on, flashes when driving above 100 Km


stop by local parts store (Autozone,Advance, etc) and have them do a free fault code test. They can print out a list of faults and clear the codes

Jan 02, 2011 | 1998 Ford Explorer

1 Answer

2004 wrangler chek engine light on. Code


a fuel cap indication would mean a leak not nessesaraly your gas cap, id check the fuel neck vent hose for a leak

Nov 04, 2009 | 2003 Jeep Wrangler

2 Answers

Emission Failed Inspection. Engine light not on.


I've always found the following to help with emissions tests on older cars: Check & replace air cleaner if dirty (difficult to see light through it), Check spark plugs ( will also be good indicator of any bad cylinder so keep them in order of removal) - if any look/measure bad, replace the set. Check engine oil quality & replace if dirty (or you can't remember the last  time it was changed). Dirty oil = higher emissions.
Run engine on higher grade fuel for a few days and during test (better fuel = lower emissions). If o2 sensor is the problem it will set off codes.

Aug 03, 2009 | Toyota Corolla Cars & Trucks

2 Answers

The check light is continously shown ON


Remove the terminal head from the battery if only you run a scan and there seem not to be any issue or code reported.

But I strongly recommend the scan.

Rate this solution.

May 14, 2009 | 1990 Toyota Land Cruiser

1 Answer

Codes for 1995 Mitsubishi eclipse


Engine-light-help.com

P1100 Induction Control Motor Position Sensor Fault

P1101 Traction Control Vacuum Solenoid Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1102 Traction Control Ventilation Solenoid Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1103 Turbocharger Wastegate Actuator

P1104 Turbocharger Wastegate Solenoid

P1105 Fuel Pressure Solenoid

P1294 Target Idle Speed Not Reached

P1295 No 5 Volt Supply To TP Sensor

P1296 No 5 Volt Supply To MAP Sensor

P1297 No Charge In MAP From Start To Run

P1300 Ignition Timing Adjustment Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1390 Timing Belt Skipped One Tooth Or More

P1391 Intermittent Loss Of CMP Or CKP Sensor Signals - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1400 Manifold Differential Pressure Sensor Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1443 EVAP Purge Control Solenoid '2' Circuit Fault

P1486 EVAP Leak Monitor Pinched Hose Detected

P1487 High Speed Radiator Fan Control Relay Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1489 High Speed Condenser Fan Control Relay Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1490 Low Speed Fan Control Relay Fault

P1492 Battery Temperature Sensor High Voltage

P1494 EVAP Ventilation Switch Or Mechanical Fault

P1495 EVAP Ventilation Solenoid Circuit Fault

P1496 5 Volt Supply Output Too Low

P1500 Alternator FR Terminal Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1600 Serial Communication Link

P1696 PCM Failure EEPROM Write Denied

P1698 No CCD Messages From TCM

P1715 Pulse Generator Assembly

P1750 Solenoid Assembly

P1791 PCM ECT Level Signal To TCM Circuit Fault

P1899 P/N Position/Transaxle Range Switch Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1751 A/T Control Relay

P1791 Engine Coolant Temperature Level Input Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1795 Throttle Position Input Circuit To TCM - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

Mar 21, 2009 | 1995 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...