Question about 2003 Chevrolet TrailBlazer

1 Answer

A/C WONT STAY COLD WHEN TRUCK IS IN PARK TRUCK NOT OVER HEATING AT ALL SO WHAT IS THE PROBLEM LOW BEAM HEAS LAMPS WENT OUT THEN ON THEN OFF AGAIN WHILE SITTING OVER NIGHT OR FOR A FEW HOURS CHANGED LOW BEAMS AND FUSES GOOD WHAT COULD IT BE NEED ASSISTANCE.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 1,150 Answers

Check with the dealer on A/C problem, there was a TSB a while back to fix that problem.
As far as the lghts are concerned, switch relay #45 with relay #46 next time the lights go out. You should have lights again. This relay tends to get corroded and or go out for some reason and is very common. Try cleaning the relay contacts along with the fuse box contacts first. If that doesn't work (did for me) get a new relay.

Posted on Mar 28, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 cavalier dash lights not working. all fuses are goood. replaced cluster, dimmer switch, multifunction switch


Back lighting or warning lights ? check engine , ABS , air bags , seat belt , oil light etc... ?
Interior Lamps Dimming
The second group includes lamps which may be dimmed. This group may use a combination of vacuum fluorescent (VF) illumination and incandescent lamps.
• Power window switches
• HVAC control head assembly
• Radio
• The instrument panel cluster (IPC)
When the ignition switch is turned to the ON position, the vacuum fluorescent (VF) display (radio) turns on at maximum brightness. When the park lamps are ON all incandescent back lighting turn ON at the dimming level indicated by the IP dimmer switch. At the same time all vacuum fluorescent (VF) displays dim to match the indicated dimming level. When the headlamp switch is placed in the PARK position, the park lamp supply voltage circuit provides an input to the body control module (BCM). The BCM then supplies voltage to the instrument panel dimmer switch through the instrument panel dimming lamps control circuit. The setting of the instrument panel dimmer switch determines the amount of voltage that the instrument panel dimmer switch supplies to the BCM through the instrument panel dimming lamps low reference circuit. The BCM then sends a pulse width modulated (PWM) voltage to all the interior lamps. All the vacuum florescent (VF) and incandescent back lighting lamps are provided a specific voltage and are then grounded. When the headlight switch is turned to the PARK or HEADLAMP position, all incandescent back lighting turn on at the dimming level indicated by the IP dimmer switch. When the IP dimmer switch is moved from MIN to MAX, all vacuum fluorescent (VF) displays, as well as all incandescent back lighting respond from Minimum intensity to maximum brightness in response to the IP dimmer switch.

I would have it checked for DTC'S - diagnostic trouble codes stored in the BCM !
DTC B2624 Display Dimming Input Range/Performance
The body control module (BCM) supplies voltage to the instrument panel dimmer switch through the instrument panel dimmer switch signal circuit. The dimmer switch varies the voltage and returns the new voltage to the BCM through the dimmer switch signal return circuit. The BCM uses this voltage to determine the illumination level of the instrument panel lamps.

DTC B2625 Display Dimming Pulse Width Modulation (PWM) Output Circuit Range/Performance
The body control module (BCM) receives a variable voltage from the instrument panel (I/P) lamp dimmer switch. The BCM uses this signal in order to vary the illumination level of the I/P lamps. The I/P dimming lamps output from the BCM is a pulse width modulated voltage supply used to light the I/P lamps. If a malfunction occurs in the I/P dimming lamps output circuit, this DTC is set.

DTC B2662 Park Lamp Switch Circuit Malfunction
The park lamps are controlled by the turn/headlamp switch. Positive battery voltage is supplied to the switch through the EXT LP fuse. When the turn/headlamp switch is placed in the park or head position, battery voltage is supplied to the park lamps. The body control module (BCM) is also connected to the park lamp circuit to sense whether or not the park lamps turn ON when the low beam or high beam headlamps are turned ON. The BCM also uses the parklamp battery positive voltage to power the instrument panel (I/P) dimmer output circuit. If the BCM senses that the low beam or high beam headlamps are ON and the park lamp input is not active, DTC B2662 sets.
Do the park lamps work ?

Jun 11, 2017 | Cars & Trucks

2 Answers

How to turn off the daytime running lights on my 2005 chevy equinox


you have to change daytime running lights module.For now remove cable from battery +

Mar 19, 2016 | Cars & Trucks

1 Answer

No low beam. Good high beam. No day lights. What's wrong?


No on the fuse . The LH HDLP and RH HDLP fuse in the fuse block - under hood, supply battery positive voltage to both low and high beam lamps at all times. For manual operation, when the headlamp switch is in the ON position, the headlamp switch supplies ground directly to the headlamps and to the body control module (BCM) on the headlamp low or high beam signal circuit, depending on the position of the headlamp dimmer switch. The BCM uses this signal to determine if the conditions are present to illuminate the daytime running lamps or park lamps.
The headlamps may be turned on 2 different ways. First, when the driver places the headlamp switch in the ON position, for manual operation. Second, with the headlamp switch placed in the OFF position activating automatic lamp control (ALC).For ALC operation, the BCM receives a signal from the ambient light sensor indicating a low or high ambient, outside, light level. Under low light conditions the BCM grounds the headlamp relay control circuit energizing the headlamp control relay. The now closed relay supplies ground through the headlamp switch to the headlamps and the BCM on the headlamp low or high beam signal circuit, depending on the position of the headlamp dimmer switch. When the BCM grounds the headlamp relay control circuit it also grounds the park lamp relay control circuit illuminating the park lamps. The headlamp relay is grounded at G203.
Daytime Running Lamps (DRL)
The low beam headlamps operate at reduced intensity when in daytime running lamps (DRL) mode. The ground circuit to the switch side of the DRL relay has a resistor in-line to reduce the intensity of the low beam headlamps for DRL operation. The body control module (BCM) receives a signal from the ambient light sensor indicating a low or high ambient, outside, light level. Under daylight conditions the BCM grounds the DRL relay control circuit energizing the DRL control relay. The now closed relay supplies ground directly to the low beam headlamps and to the BCM on the headlamp low beam signal circuit. The low beam headlamps now illuminate with reduced intensity. The DRL relay is grounded at G203. Any time the headlamps are illuminated the DRL will not illuminate. Manual park lamps do not effect DRL operation.

Feb 23, 2016 | 2005 Chevrolet Equinox LS

1 Answer

Where is the DRL relay located?


There is no DRL relay , has a lamp control module .
The daytime running lamps (DRL) activate under the following conditions:
?€¢
The ignition switch is in the RUN position.


?€¢
The ambient light sensor indicates daylight.


?€¢
The vehicle is not in the PARK position.

When the above conditions are met, the lamp control module (LCM) supplies battery positive voltage (B+) to the low beam headlamps through CKT 589 (GRY), the DRL resistor, and CKT 12 (TAN). The DRL resistor reduces the voltage supplied by the LCM. The low beam headlamps light at a reduced intensity. The DRL disable if the vehicle is placed in the PARK position. When the ambient light sensor indicates darkness, the low beam headlamps automatically switch from a reduced intensity to a regular intensity.
Lamp Control Module (LCM)
In the center of the IP, below the center heater outlets

Nov 17, 2015 | 1998 Oldsmobile 88

1 Answer

Why wont the headights or running lights work on my 2002 Buick LaSabre?


There are several reasons why your headlamps an running lights don't work , the headlamp switch is a good one ,plus relays an the DIM - dash integrated module an associated wiring ! Here is how the headlamps work , right out of Buick factory service info !
The dash integration module (DIM) provides battery positive voltage to the signal circuits of the headlamp switch. The signal circuits include the headlamp switch headlamps on signal, the flash to pass switch signal and the high beam input. With the headlamp switch in the ON position, a ground path is available for the headlamp switch headlamps on signal circuit of the DIM through the headlamp switch. The DIM provides ground to either the headlamps high beam relay control circuit or the headlamps low beam relay control circuit of the low beam circuit. The position of the headlamp dimmer switch determines which relay control circuit has ground. The DIM supplies battery positive voltage to the relay control circuits, if the headlamps are necessary. The fuse block - underhood supplies battery positive voltage to both relay switch circuits. When the low beam relay control circuit is energized, current flow is to both low beam fuses and to the low beam headlamps. The headlamps have ground at G103 and at G401. When the headlamp high beam relay control circuit is energized, current flow is to both high beam fuses and to the high beam headlamps. The high beam circuit is divided into a left and right side circuit. The current flow of the left high beam is from the fuse to the left high beam lamp. From the lamp, the current flows to the normally-closed contact of the DRL relay to G103. The current flow of the right high beam is from the fuse to the right high beam lamp. From the lamp, the current flow is to ground at G401. When the headlamp dimmer switch lever is pulled toward the driver, the flash-to-pass switch closes. This grounds the DIM flash to pass switch signal circuit. In response to this input, the DIM energizes the HDLP HI BM relay. Both high beams remain on until the driver releases the switch handle. If the low beam headlamps were on during a flash to pass operation, the low beams remain on. The headlights may be switched to high beam with the opposite movement of the headlamp dimmer switch lever.
By running lights , do you mean park lamps or day time running lamps ?
Park, Tail, License and Marker Lamps
The park lamps, including the license lamps, are turned on when the headlamp switch is placed in the PARK or ON position or anytime the headlights are requested. The fuse block - rear supplies battery positive voltage to the switch contacts of the Park LP relay. When the headlamp switch is in PARK or in ON, the park lamp switch on signal circuit of the DIM has a ground path. The DIM provides battery positive voltage to the control circuit of the Park LP relay. When the park lamps and/or the tail lamps are ON, the DIM energizes the park lamp relay control circuit. This closes the switch contacts. Current flows from the Park LP relay to the LH PARK LP and the RH PARK LP fuses. From the fuse, the current flows to the park lamps. The left park lamps are grounded at G103, G401 and G402. The right park lamps and the right tail lamps are grounded at G103 and G401. The DIMR fuse supplies battery positive voltage to the license lamps and to the DIM instrument panel lamp fuse supply voltage - 1 circuit, for interior lamps dimming. The license lamps are grounded at G401.
The best advice I can give is that you take this to a ASE certified professional repair facility unless your a qualified automotive electric repair person !
Diagnostic Starting Point - Lighting Systems
Begin the system diagnosis with the Diagnostic System Check - Lighting Systems . The Diagnostic System Check will provide the following information:
?€¢
The identification of the control modules which command the system


?€¢
The ability of the control modules to communicate through the serial data circuit


?€¢
The identification of any stored diagnostic trouble codes (DTCs) and their status

The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and where the procedure is located.

The

Mar 15, 2015 | 2002 Buick LeSabre

1 Answer

Low beam not working on 97 Mitsubishi Lancer. Park ok, hi beam ok. Lamps test ok.


If Dual beam bulbs, low beam on light may be blown. I just had the same problem on my '91 Camaro. Could also be a simple fuse replacement, find correct fuse, , replace, and recheck.

Sep 26, 2013 | Mitsubishi Lancer Cars & Trucks

1 Answer

Daytime running lamps won't come on


check fuse under the hood in the main control panel fuse box.

Jun 14, 2010 | 2006 Pontiac Grand Prix

1 Answer

No low beam head lamps,replaced pcm and it only lasted a year.truck also burns out multifunction switches.


mine did this one time, then went away, never did it again, never did figure out why

Oct 28, 2009 | 2004 Dodge Ram 2500

1 Answer

Need fuse box pannel to see what fuse is what


FUSE USAGE

1. 10 AMP LOW BEAM-LEFT
2. 10 AMP LOW BEAM-RIGHT
3. 30 AMP BRKR POWER WDO/SUNROOF
4. 30 AMP BRKR PWR ACSRY
5. 20 AMP BRKR LIGHNG CONTROL MODULE
6. 15 AMP IGN/REM ACSRY CONT/INST CSTR
7. 10 AMP SUPPLEMENTAL INFLATABLE RST
8. 20 AMP CORNERING LPS/TURN SIG
9. 10 AMP CRANK SIGNAL-SIR
10. 20 AMP TRK REL/FUEL FILL REL/BACK-UP LPS
11. 15 AMP BAT/RADIO/PWR ANT/CIG LGTR/ INST CSTR
12. 20 AMP ELECTRONIC LEVEL CONTROL
13. 20 AMP BRAKE & HAZARD LAMPS
14. 15 AMP PARK LAMPS
15. 15 AMP COURTESY LPS/PWR MIRRORS
16. 10 AMP COOLING FAN
17. 25 AMP HEATING/AIR CONDITIONING (C67)
18. 15 AMP A/C AUTOMATIC ELECTRONIC (CJ2)
19. 10 AMP ANTILOCK BRAKES
20. 10 AMP LOW COOLANT/LAMP MONITOR
21. 10 AMP IP LIGHTS
22. 10 AMP HI BEAM-RIGHT
23. 10 AMP HI BEAM-LEFT
24 10 AMP IGNITION/RADIO
25 25 AMP WIPER/WASHER

FOR ACCESS TO ADDITIONAL FUSES
REMOVE RIHT SOUND INSULATOR

May 16, 2009 | 1991 Buick Park Avenue

2 Answers

Headlights wont burn on low beam


check to make sure that both lamps aren't burnt out-halogens like to do that.

Jul 24, 2008 | 1985 Nissan Pickup

Not finding what you are looking for?
2003 Chevrolet TrailBlazer Logo

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...