Question about Saturn SL

Open Question

Reads codes p0340 and p0341 - SL Saturn Cars & Trucks

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: 2005 dodge diesel codes!

Hi..
the Code P0340, Camshaft Position sensor problem or Loss signal.
The Code P0341, Camshaft Position sensor Intermitent Signal.

The First step you should do is : Locate the Camsahaft sensor,
Is located On Right Front of the Engine..
It use a 3 wires Connector.
1-- Pink/Yellow
2-- Brown/Orange
3-- Dark blue/Gray.

After you found it. Inspect the Connector. If is The connector in good condition.
Replace the Camshaft Position sensor...

Ok... I hope this help on your problem..
Thank you for use Fixya...

Posted on Sep 27, 2008

Ad
johnjohn2
  • 5763 Answers

SOURCE: P0340 & P0341 CODES CAME UP THE OTHER DAY, I

how many miles on the car , if its over 70,000 miles then yes you should.hope this helps.

Posted on Oct 17, 2009

  • 280 Answers

SOURCE: code reads P0340 Camshaft position Sensor circuit

That makes the computor think the timing is off. Replace the sensor and see if that does it. You will then have to have the code cleared (erased) or the light will come back on/stay on.

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code PO341 came up on scanner how do I test the sensor want to be sure its not the wires


his P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal.

Read more at: http://www.obd-codes.com/p0341
Copyright OBD-Codes.com

Apr 14, 2016 | Cars & Trucks

1 Answer

I have a po340 a po341 an a po016 code on a 2006 dodge caravan want start


Hi !
P0340 = This indicates that a problem was detected in the camshaft position sensor circuit.
P0341 = Camshaft Position Sensor Circuit Range/Performance
P0016 = Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

The common point of these errors is the camshaft sensor, so I'm afraid you need to visit a service.

Apr 24, 2014 | Cars & Trucks

2 Answers

Po341 code cts


Camshaft position sensor A circuit range /performance bank 1 or single sensor

Mar 06, 2014 | 2003 Cadillac CTS

1 Answer

WHAT IS THE CODE P0341


This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook Symptoms The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in "limp-in/limp-home" mode even with a cam sensor signal problem. There may be no noticeable symptoms other than:
  • Poor fuel economy (if engine runs)
  • Possible no start condition
Causes A code P0341 may mean that one or more of the following has happened:
  • Cam sensor wiring routed too close to spark plug wiring (causing interference)
  • Poor wiring connection at cam sensor
  • Poor wiring connection at PCM
  • Bad cam sensor
  • Damaged reluctor wheel
Possible Solutions Often relacing the sensor fixes this code, but not necessarily. Therefore it's important to check the following:
  • Check that the wiring isn't routed too close to any secondary ignition components (coil, spark plug wires, etc.)
  • Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing
  • Visually inspect the cam sensor for damage
  • Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage
  • If reluctor isn't visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design)
  • If all checks out okay, then replace the sensor.
Related Camshaft Trouble Codes: P0340

Mar 07, 2012 | 1996 Saturn SL

2 Answers

Truck starts everytime but cuts off 4 or 5 times within 1or2 hours of driving is this the cam sensor bad


that is very possibly the reason, do you have a check engine light on the dash? Other possibilities are fuel pressure dropping as the pump gets warmer, leaking injectors or o-rings, or crank sensor heat sink problems. even if your check engine light is not on, you may have a 'pending' code' that can be read if you have a scanner hooked to the OBDII port-most commercial retail auto parts stores will do this for no charge, just make sure they tell you the actual code (i.e. cam sensor codes are usually P0340-P0341)

Apr 14, 2011 | 2000 GMC Jimmy

1 Answer

I have an 06 Cobalt and recently had the codes P0340 & P0341. I went to the first mechanic who changed the O2 sensor and told me I did not have a camshaft sensor. I then took it to a second mechanic...


I'm not sure what size your engine is but I believe on the 2.2L the camshaft position sensor is at the front right hand side of the valve cover. The 2.4L is the same but with another cam sensor on the exact opposite (back) side of the valve cover, closest to the firewall.I don't know about it on a 2.0L, probably close to the same. The 2.4L also has two cam actuator solenoids (one for exhaust and one for intake, marked on valve cover) on the left hand side of the valve cover, directly on top. Each part costs in a range of $20-60 depending on where you go. Hope this helps.
P0340 - Camshaft Position Sensor Circuit Malfunction
P0341 - Camshaft Position Sensor Circuit Range/Performance

Dec 12, 2010 | 2006 Chevrolet Cobalt

2 Answers

P0340 & P0341 CODES CAME UP THE OTHER DAY, I KNOW IT'S THE CAMSHAFT SENOR. I WAS WONDERING SHOULD I JUST GET A TUNE UP...I'T EXPENSIVE...$375


tune up wont fix it, need to have diagnosed before you have tune-up and i hope that tune up comes with plug wires for that price

Oct 17, 2009 | 2000 Cadillac DeVille

1 Answer

2005 dodge diesel codes!


Hi..
the Code P0340, Camshaft Position sensor problem or Loss signal.
The Code P0341, Camshaft Position sensor Intermitent Signal.

The First step you should do is : Locate the Camsahaft sensor,
Is located On Right Front of the Engine..
It use a 3 wires Connector.
1-- Pink/Yellow
2-- Brown/Orange
3-- Dark blue/Gray.

After you found it. Inspect the Connector. If is The connector in good condition.
Replace the Camshaft Position sensor...

Ok... I hope this help on your problem..
Thank you for use Fixya...

Sep 27, 2008 | 2005 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...