Question about 2002 Mazda MPV

3 Answers

Mazda mpv engine idle problem - 2002 Mazda MPV

Posted by on

  • 1 more comment 
  • tcabrera001 Sep 07, 2008

    My 2004 mpv was idleing rough and acted as if it was going to stall. I took it to my mechanic and he changer the #6 coil and it was running great. Then 3mo later it started again. I took it back and they told me that I had to take it to the dealership because it needed to be reprogrammed. The dealership said it was not that and that all the coils except #6 needed to be changed along with the spark plugs and the pcv hose. I had my dad do it who is a mechanic,and it still is doing the same problem. HELP!!!

  • tonyp180 Dec 22, 2008

    I have the same problem with my '03 mpv, with this problem cause the check engine light to go on/off also?

  • Lisa Lujano Jan 07, 2009

    I have a similar problem.could you tell me where the IAC is located. I'll have my dad look into it for me. Thank You

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had the same problem with my 2002 MPV. I ended up removing the IAC Idle are-control myself, and cleaning it really well (with some air intake cleaner). Put it back together, and it's been running great for the past year.

Not too difficult of a project, I'm no mechanic, but if your good with tools, it's not to bad.

Posted on Oct 10, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

My mpv sport mazda stop to work on the road .the battery is good and the fuel to .but i can not start again.

Posted on Sep 06, 2010

  • Reynaldo Cespedes
    Reynaldo Cespedes Sep 06, 2010

    my mpv sport mazda stop to work on the road .the battery is good and the fuel to .but i can not start again.

×

I've heard that carbon build up can be a major problem in Mazda's. The idle air-control sylanoid may need to be replaced and a good engine flush may be in order.

Posted on Oct 09, 2008

5 Suggested Answers

  • 1 Answer

SOURCE: 2003 Mazda Mpv jerks when idling abd breaking

Check to see if you have a MPV that has been included in the recall for the PCV line. Yes it is difficault to get to on your own, however they have special tools to reach behind the manifold to remove the line and install a new one. If you do it on your own it is very difficaul and will take a few hours as a I did before I found out about the recall. The service dept. should have asked you about the recall when you went to get the part from them. Where I got pissed was when they did replace the hose the faulty line had fouled the pcv valve and they did not bother to replace it and that is tucked under the intake manifold and under the fuel rails.

Posted on Feb 04, 2009

StormStrikes
  • 104 Answers

SOURCE: how do i get the trouble codes off a 1989 mazda mpv?

http://img178.imageshack.us/img178/3331/obdikx3.jpg

The above link is to a diagram of your ALDL connector, all you need is a paper clip, straighten out the paper clip and insert one end into the diagnostic test pin and one in the system ground pin (terminals A & B).

Then put the key in the ignition and turn it to the on position but DO NOT start the engine. You will then see the check engine light flash. It will initially start by flashing once, then a pause and then flash twice and it will repeat this three times. That flash sequence indicates 12, which just means the system is operating. Its the flash sequences after that that will give you the code if any are stored.

For instance if it flashes twice, then pauses, then flashes four times, thats code 24. So any flash sequence you get after the initial 12 (flash once, pause, flash twice) you need write those down. Below is a list of diagnostic codes to tell you what the codes mean.

Code 12
1 flash, pause, 2 flashes
Diagnostic: This Code will flash whenever the diagnostic terminal is grounded with the ignition switch turned on and the engine is not running.

Code 13
1 flash, pause 3 flashes
Oxygen sensor voltage stays between 0.35 and 0.55 volts for 30 seconds when the TPS signal was above 0.55 volts. The engine had been running for at least 40 seconds with an engine temperature above 110° F.

Code 14
1 flash, pause, 4 flashes
Coolant temperature sensor signal indicates a temperature of over 284° F for 4 seconds after the engine had been running for at least 10 secondsCoolant Sensor Circuit (high temperature) If the engine is experiencing overheating problems, have those fixed before continuing. Check all wiring and connectors associated with the coolant temperature sensor. Replace the Coolant temperature sensor.

Code 15
1 flash, pause, 5 flashes
Coolant Sensor Circuit (low temperature) Coolant temperature sensor signal indicates a temperature colder than -36° F for at least 4 seconds after the engine had been running for 2 seconds. See above, then check wiring connections at the ECM

Code 16
1 flash, pause, 6 flashes
Charging system voltage was either below 9 volts or above 17 volts for 10 seconds. System High Voltage If the voltage is above 17.1 volts for more than 2 seconds, the Service Engine Soon light will illuminate. Have the charging system checked.

Code 17
1 flash, pause, 7 flashes
PCM did not detect any spark reference pulses within 240 fuel control reference pulses (80 crank revolutions) while engine was running below 1200 RPM. Spark Reference Circuit.

Code 21
2 flashes, pause, 1 flash
Throttle Position Sensor, TPS voltage was above 0.8 volts for 5 seconds when engine was running and air flow was less than 15 gm/sec, or the TPS voltage was over 4.8 volts at any time.

Code 22
2 flashes, pause, 2 flashes
Throttle Position Sensor check TPS adjustment. Replace the TPS sensor. TPS voltage was under 0.2 volts for 4 seconds when the ignition was on. Check for a sticking, or mis-adjusted throttle position sensor.

Code 23
2 flashes, pause, 3 flashes
Inlet air temperature sensor signal showed an air temperature of -29° F for 4 seconds. Manifold Air Temperature. Check the MAT sensor, wiring, and connectors for a possible open circuit. replace the MAT sensor.

Code 24
2 flashes, pause, 4 flashes
Vehicle speed sensor signal showed less than 3 MPH for 2 seconds when engine speed was greater than 3000 RPM and transmission has not been in park or neutral for more than 4 seconds. Or vehicle speed goes from above 18 MPH to 0 in less than 2 seconds without applying brake. This code can only appear when the vehicle is in motion, if it appears when the car is not in motion, ignore it. Check ECM connections, any other problems should be diagnosed by a qualified mechanic.

Code 25
2 flashes, pause, 5 flashes
Inlet air temperature sensor signal showed an air temperature of over 218° F for 5 seconds when vehicle speed was greater than 35 MPH. Check the voltage between the MAT sensor and the ECM. voltage should be above 4 volts.

Code 26
2 flashes, pause, 6 flashes
Quad-Driver sense voltage shows a low voltage when battery voltage should be present, or if the sense voltage shows battery voltage when a low voltage should be present for at least 5 seconds when the engine was running. Have the car checked by a dealer.

Code 27
2 flashes, pause, 7 flashes
2nd gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 2nd or 4th gear switch was open when engine was first started. Gear switch Diagnosis Have the car checked by a dealer.

Code 28
2 flashes, pause, 8 flashes
3rd gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 3rd or 4th gear switch was open when engine was first started.

Code 29
2 flashes, pause, 9 flashes
4th gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 4th gear switch was open when engine was first started.

Code 31
3 flashes, pause, 1 flash
PRNDL indicates a gear other than park or neutral for 13 seconds for 3 consecutive startups when ignition was on, engine was off and vehicle speed was 0. Or the PRNDL status indicators (A, B, C, P) showed an incorrect combination of Lo and Hi for more than 10 seconds.
Check all connectors, and for a faulty switch.

Code 32
3 flashes, pause 2 flashes
EGR System Check vacuum hoses and connections for leaks and restrictions. Replace the EGR solenoid or valve.

Code 33
3 flashes, pause, 3 flashes
MAF Sensor Have the mass air flow sensor replaced.

Code 34
3 flashes, pause, 4 flashes
There was no MAF signal for over 4 seconds while engine was running. Check for loose or damaged air duct, misadjusted minimum idle speed and cacuum leaks. Inspect the MAF sensor and the electrical connections.

Code 38
3 flashes, pause, 8 flashes
The Torque Converter Clutch portion of the brake switch was open and caused the TCC to be inoperative, adjust OR replace switch.

Code 39
3 flashes, pause, 9 flashes
Torque Converter Clutch Check ECM connections, check for faulty Torque Conver Clutch solenoid.

Code 41
3 flashes, pause, 1 flash
Cam sensor signal was not received by PCM for the last 5 seconds while engine was running. Check for faulty connections, or a faulty cam sensor. Maybe also indicate a problem with the vehicle's timing chain.

Code 42
4 flashes, pause, 2 flashes
The Electronic Spark Timing (EST) signal did not change when the ECM applied bypass voltage to the ignition module. Check for faulty connections, or a faulty ignition module.

Code 43
4 flashes, pause, 3 flashes
Knock sensor signal was either above 3.5 volts or below 1.5 volts for at least 20 seconds. Check for a faulty knock sensor, or Mem-Cal.

Code 44
4 flashes, pause, 4 flashes
Oxygen sensor voltage was under 0.25 volts for up to 4 1/2 minutes of closed loop operation, lean exhaust. Check the ECM wiring connections. Check for vacuum leaks at the hoses and intake manifold gasket.

Code 45
4 flashes, pause, 5 flashes
Oxygen sensor voltage was over 0.75 volts for 2 minutes in closed loop operation with a throttle angle between 0.6 and 1.9 volts. Rich exhaust. Check the evaporative charcoal canister and its components for the presence of fuel.

Code 46
4 flashes, pause, 6 flashes
Power Steering pressure switch Check for faulty connections, or a faulty switch.

Code 48
4 flashes, pause 8 flashes
Misfire Diagnosis. Check the ignition and fuel systems.

Code 51
5 flashes, pause, 1 flash
Prom or Mem-Cal Make sure the MEM-Cal or prom is properly installed in the ECM. Replace Mem-Cal or prom.

Code 52
5 flashes, pause, 2 flashes
Cal-Pak Check the Cal-Pak to insure properation. replace the Cal-Pak.


Code 54
5 flashes, pause, 4 flashes
EGR #2 solenoid was out of range for 6 of 8 tests. 55 EGR #3 solenoid was out of range for 3 of 5 tests.

Code 55
5 flashes, pause, 5 flashes
ECM Check for faulty connections. Replace the ECM.

Code 56
5 flashes, pause, 6 flashes
Quad-driver voltage was incorrect for 5 seconds on the circuit connected to QDM "B".

Code 57
5 flashes, pause, 7 flashes
Boost control solenoid did not open bypass valve causing engine torque to be too high.

Code 63
6 flashes, pause, 3 flashes
EGR flow was incorrect. EGR solenoid did not work properly. Have vehicle serviced by a dealer.

Code 64
6 flashes, pause, 4 flashes
Same as Code 63 EGR flow was incorrect. EGR solenoid did not work properly.

Code 65
6 flashes, pause, 5 flashes
Same as Code 63.

Posted on Dec 31, 2008

emissionwiz
  • 60667 Answers

SOURCE: water pump replacement in a 2002 Mazda MPV

The reason is the water pump is driven off the timing belt, extra parts and allot more labor. No the eng does not have to be removed, labor time around 4 hours, parts about, about $125 US for parts, if it is a dealer add $75 US

Posted on Jan 08, 2009

  • 90 Answers

SOURCE: shaking mazda mpv 2003 in idle and loud radiator fan

Hello there, As far as the check engine light I would think since you mentioned it shacking that your light will probably be on for a misfire, Meaning most likely you have a spark plug wire going bad. I would stop by somewhere such as Autozone for a free check to tell you why your light is on just to double check.

Your fan issue could be several different things such as the fan motor going bad or the blades could be rubbing something, that one is a little tricky without hearing it.

Good Luck and I hope this does help you some. Allen

Posted on Oct 04, 2009

  • 78 Answers

SOURCE: 2003 Mazda MPV ES that idles very rough when warm

that means could be vacuum leak

Posted on Jan 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Misfire but no check engine light mazda mpv


Scanning tells a lot. But if your not getting an engine light. Check vacuum lines first. But if you turn the key on and don't see the light. it blew or someone took it out. Then yes, start with having the codes read.

Oct 03, 2016 | 2003 Mazda MPV

1 Answer

Engine rpm,s too high on a 2004 mpv mazda


cheak for the theromsate switch ,might be not working

Oct 08, 2012 | 2004 Mazda MPV

1 Answer

2004 mazda mpv engine racing and cooling fan not working


coolant temp sensor tells the computer how hot or cold the engine is so it can regulate the idle and fuel mixture, when it fails there usually is no cooling fan and you will have trouble starting the engine and keeping it running.

Oct 08, 2012 | 2004 Mazda MPV

1 Answer

Mazda mpv 2000 check engine light on code p1512 how to fix?


Idle Charge Actuator Mechanical malfunction. May have a bad O2 sensor or actuator.

Sep 11, 2012 | 2000 Mazda MPV

2 Answers

While my mazda mpv engine is on and warmed and park it would idle to 2500 rpm and stay and make a loud noise from the engine i would have to step on the gas pedal for it to go back to nornal. it would also...


sounds like your throttle cable is sticking or your choke cable spray a good lubricant on the cable where the linkage is, get someone to lightly step on the gas while you are under the hood and watch where the cable turns the linkage spray it there and see if that resolves the problem

Jan 09, 2010 | 2000 Mazda MPV

1 Answer

1997 Mazda 3.0 MPv Idle problem


check MAF sensor or for vacuum leaks

Oct 20, 2009 | 1997 Mazda MPV

3 Answers

What's the firing order is for a 2002 mazda mpv 3.0L/6 cylinder engine?


b70a6c7.gif
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

May 22, 2009 | 2002 Mazda MPV

1 Answer

Mazda mpv engine


You need to have the system tested, but I think you have a spark plug wire that is shorted out.

Sep 25, 2008 | 2003 Mazda MPV

Not finding what you are looking for?
2002 Mazda MPV Logo

Related Topics:

3,478 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...