Question about Toyota Land Cruiser

1 Answer

My cruiser feels like its running on 5 cylinders

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 176 Answers

Could need a tune up, have a bad catalytic converter, bad ignition coils, or a number of other things. Is the check engine light on? If you want to try and diagnose the issue, I will be happy to further assist you.

Posted on Mar 28, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Firing order on a 93 land cruiser


Hi Jessica:
If this is the straight 6 cylinder motor, they were basically very similar to the chevy. The firing order was 1 5 3 6 2 4
If you look at the distributor, find the number 1 plug wire, and then check from there it should confirm it for you.
Gotta love old chevys!

Jun 19, 2015 | 1993 Toyota Land Cruiser

2 Answers

Toyota land cruiser 1998 p0305


p0305 = Cylinder 5 misfire detected.
Check the coil wiring harness and connector plugs.

May 09, 2015 | 1998 Toyota Land Cruiser

2 Answers

Clutch feels loose,no pressure. gears are stuck, shifter wont moveis it the clutch adjustment?


The Clutch Master Cylinder or the Clutch Slave Cylinder has a leak. From under the dashboard, located the Clutch Master Cyliner Boot and pry one side open. If hydraulic fluid drips out, the piston seal(s) in the cylinder are worn. You'll need to replace the cylinder.

Dec 27, 2014 | 2003 Chrysler PT Cruiser

1 Answer

How to knock sensor location


you didn't state specific engine so here is a run down of locations
on a 4 cylinder engine there are 2 knock sensors located on the inlet side of the block adjacent to no 1 and 4 cylinders ( cross way motor)
on a v6 engine( crossway engine) they are in the valley of the block ( probably under the inlet manifold system) at 2 and 5 cylinder positions
on a v8 they will be located adjacent to 4 cylinder and between 6 and 8 cylinder on one side and adjacent to 3 cylinder and between 5 and 7 cylinder on the other side

Nov 22, 2014 | 2000 Toyota Land Cruiser

2 Answers

2003pt cruiser limited overheats antifreeze com ng


Blown headgasket,letting coolant into the combustion chamber.

Sep 12, 2014 | 2003 Chrysler PT Cruiser

1 Answer

What's the Cylinder timing numbers for a 1989


http://autorepair.about.com/library/firing_orders/bl-to, I needed motor size ,but also found 6cyl gas model =1, 5 ,3 ,6 ,2 ,4 firing order

Sep 09, 2014 | 1989 Toyota Land Cruiser

1 Answer

What could cause a 2002 pt cruiser to have a rough idle, cylinder 1 misfire, and bogging upon acceleration?


AIR & FUEL FILTERS NEED CHANGED, MAP SENSOR CAN BE FAULTY ! PUT SOME FUEL INJECTOR CLEANER IN TANK, THE GOOD STUFF ! DO ALL THIS, SEE HOW IT DOES .

Mar 26, 2013 | 2002 Chrysler PT Cruiser

1 Answer

2002 pt cruiser belt replacement diagram


Asked under 2001 Category for a 2002 Question.

Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 2002 Chrysler PT Cruiser 2.4L DOHC In-Line 4-Cylinder Engine with the Engine Options (AC/No AC etc.). It also has Instructional and Directional Diagrams inorder to remove and/or replace the Belt(s).
Note: the differences between the Automatic Tensioner and those Tensioners with Adjusting/Locking Bolts/Nuts

http://www.2carpros.com/car_repair_information/year/2002/make/chrysler/model/pt_cruiser/2002_chrysler_pt_cruiser_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Mar 28, 2010 | 2001 Chrysler PT Cruiser

1 Answer

Where can I get the user and service/repair manual Toyota HZJ77?


Try http://www.toyota.com

Make enquiries from them, they'll send you a pdf if you request for 1.

Rate this

Apr 06, 2009 | 1991 Toyota Land Cruiser

1 Answer

Car runs rough


check the compression of each cylinder, they should be no more than 5% difference between cylinders, so if the highest is 160 PSI then the lowest should not be lower than 150 PSI. also test the fuel injectors for proper flow, check for intake manifold vacuum leaks as well.

Mar 31, 2009 | 1994 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...