Question about 1987 Toyota Camry

1 Answer

What side battery do this care use 4 door standard shift 4 cyclinder

Posted by on

1 Answer

That is a question you ask at the auto parts store

Posted on Mar 28, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When the car is turn on the stick shift will not move, but when the car is off it moves.


When this happend just a couple months ago to me it was the slave cylinder.

Dec 28, 2011 | 2006 Saturn Vue

2 Answers

Where is the location of the ignition sensor on 2004 kia optima lx 4 cyclinder 4 door sedan


the ignition module is to the left of the air filter, right against the right side of the engine. I replaced mine, just two screws and take off black plastic covering. Make sure u disconnect negative battery post first. When done hook negative back up. If engine light don"t go off for P0320 code, disconnect battery for 5 min and connect back, I let my battery stay disconnect overnight.

Jul 22, 2010 | 2004 Kia Optima

1 Answer

1997 mercury villager passenger side mirror replacement guide. how do i do it? is there an easy access panel or does the whole door panel need to be removed


door panel must come off.

go here for villager help

http://groups.yahoo.com/group/villagerquest/

Section 01-05: Trim, Interior 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door
Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. svv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel.
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure. Body Side
Removal
  1. Gently pry loose the body side door latch handle bezel and remove it.
  1. Slide a suitable tool behind each of the retainers and twist the tool to disengage the body side door trim panel from the body side door (24622).




Installation
To install, reverse the removal procedure. Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal
  1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
  1. Remove the front door watershield by carefully detaching it from the adhesive.
Installation
  1. Install the front door watershield in the proper position and press firmly at the adhesive areas. If necessary, use additional adhesive to ensure an adequate seal.
  1. Install the Front Door Trim Panel . Refer to the installation procedure in this section.

May 22, 2010 | 1998 Mercury Villager

2 Answers

Timing diagram? Fire order? counter clock wise? 10 degreees? on Distributer where is number 1 located? TDC?


no 1 front left hand side ,engine rotates clockwise ,10ª might be too much for unleaded fuel 95octane i would go for 6/8 degrees unless you are putting in a lead substitute .firing order 153624

May 09, 2009 | 1985 Cadillac Fleetwood

2 Answers

Starter motor


Is there any sound when the key is turned? The solenoid may be stuck, and a light tap with a hammer may free it up. The starter is located on the engine block.

This is what you are looking for....
http://i8.ebayimg.com/02/i/001/22/0b/39e7_1.JPG


REMOVAL & INSTALLATION
STARTER MOTOR
Removal & Installation (2.0L)

CAUTION:When battery is disconnected, vehicle computer and memory systems may lose memory data. Driveability problems may exist until computer systems have completed a relearn cycle. See COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION before disconnecting battery. Before testing starter, ensure transmission is in Park or Neutral.

Disconnect negative battery cable. Remove air cleaner. Remove upper starter mounting bolts. Raise and support vehicle. Disconnect starter solenoid wire connections. Remove starter motor lower mounting bolt. Remove starter motor. To install, reverse removal procedure. Ensure negative battery cable is installed with starter mounting bolt. Tighten bolts to specification. See TORQUE SPECIFICATIONS table.

Removal & Installation (2.5L)

Disconnect negative battery cable. Remove air cleaner and air cleaner bracket. Disconnect starter solenoid wire connections. Remove starter support bracket. On manual transmission equipped models, remove shift cable bracket and disconnect cable. On all models, remove fuel supply line from support bracket. Remove starter bolts. Remove starter. To install, reverse removal procedure. Tighten bolts to specification.

Jan 01, 2009 | 2000 Ford Contour

Not finding what you are looking for?
1987 Toyota Camry Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...