Question about 2005 Chrysler Town & Country

Open Question

Horn on 2006 T & Country will not work. Took of the horn, cut the wires, put it to 12 volts and they light up like a christmas tree. Checked the Fuses and also the relay. There is the correct voltage to the relay but when I push the steering wheel, there is no continuity on the leads to the coil of the relay. The horn lock function does not work either so to me, that rules out a broken wire in the steering wheel. Do you think it is the Voltage Distribution Module?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: 2002 dodge caravan horn doesn't work

Pull battery cable(s), to be sure airbag disarmed, and check for continuity rather than power?

Posted on Jan 11, 2009

emissionwiz
  • 75797 Answers

SOURCE: Van won't start. Just makes a clikcing noise. Horn sounds weak.

THIS IS CAUSED BY A DEFECTIVE STARTER MOTOR SOLENOID, REMOVE AND REPLACE THE STARTER OR JUST REPLACE THE SOLENOID ON TOP OF THE STARTER IF YOU CAN BUY IT SEPERATE.

Posted on Jul 04, 2009

alicantecoli
  • 22114 Answers

SOURCE: No horn....checked fuses but where is the relay

get a nice young dolly birn to hold horn switch down then tap horn with a small hammer a couple of times ,if it doesnt work the replace the horn as they corrode up with lack of use

Posted on Aug 02, 2009

centralvalle
  • 386 Answers

SOURCE: Horn wont honk. Fuse is good and horn honks when

check relay , yes , also check ground circuit, if horn grounds by it's mount or by external wire... check all.. also check horn button contacts go bad or horn brush in steering wheel...

Posted on Aug 04, 2009

  • 490 Answers

SOURCE: 2005 sebring convertible- horn goes off by itself for 30 seconds

FIrst off the horn's ground works through the steering wheel,so the wire is bare or the end is broken and grounding in a place where it should not. You will have to check the wires for the horn from the fuse box up to the wheel.
your power feed to the headlights and the door locks has an open ( the power is not connected somewhere ) Perform a wiggle test turn on the headlights and lift the hood,find the power distribution box and begin to wiggle the wire harness.Sometimes the chrysler fuse box under the hood get loose inside the power distribution box,it will have to be broken down all the way to the heavy wires comming out of hte box,you can tighten these connections your self.

Posted on Aug 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 DODGE HORN DON'T WORK


is you horn button working? have you tried a volt/ohm; meter?
using the volt meter you can tell if the horn button is working put the black probe to ground and pull the hot wire off the horn and attach the red probe and push the horn if you get 12 volts or close button is working maybe you would like to purchase a repair manual for your
dodge at your local auto parts store just in case something else goes wrong you can look in your manual and have a idea of what it takes to repair so garage won't tell you a fish story like this; happened to me: told shop manager that my a/c unit would cool and then it would blow heat he said my compressor was froze up and it would cost between $800 & $900 to fix first a frozen compressor will not cool and the shaft will not turn when I had time checked it out it was a $12.95 expansion valve that was plugged up garage must have been hurting for money

Aug 02, 2017 | Dodge Cars & Trucks

1 Answer

2007 Ford Explorer horn quit working?


suggest checking if 12 volts goes to horn wire at horn end when horn pressed from inside vehicle. A 12 Volt probe {google it} can be a cheap checking tool for this.
If 12v volts is switched when button is pressed {could be earth being switched if it is then place probe on constant 12 volts and negative lead on switched earth wire} then the horn itself is faulty.
If no voltage switched then horn relay needs to be checked. check if voltage at horn relay coil contact when button pressed.
if yes then relay may be faulty. if no then horn switch could be faulty.
you can check switched voltage also at horn relay switched contact when relay plugged in. To see if relay is doing what it is meant to do

Jan 16, 2017 | 2007 Ford Explorer

1 Answer

My maruti 800 horn is not working i have checked all the fuses they all are right


check horn dc supply using 12 volt dc bulb, if there is proper dc supply, adjust horn's rear adjusting screw, otherwise replace the horn

Apr 11, 2014 | 2006 Suzuki Swift

1 Answer

Audi 2006 A6 Squirter not working


Have your mechanic check for 12 volts to the horns when the horn button is depressed. If 12 volts are present, the horns are defective. If zero volts, check horn relay and check for bad connections.


-------------------------------------------------------
GM Tech2 GM Diagnostic Scanner

Dec 22, 2012 | 2006 Audi A6

1 Answer

94 pontiac bonneville horn does not work. i have checked fuse and it is good.


Ok , try this. have an other person push the horn button while you check for voltage at the horn wire. red wire from meter to horn wire and black to ground on car. should get 12 volts, or you can also use a test light. if it light up the circuit is good, or if you read 12 v on meter. replace horn. if not then find horn relay and replace it. sorry i'm not sure where that is located. might have to follow wire from horn back to it . possible under hood on the firewall. if that is not it then the only thing left is the switch in the steering wheel is not making contact. that is all to the horn circuit. hope this helps.

Sep 10, 2010 | 1994 Pontiac Bonneville

1 Answer

Horn doesn't work on 1990 chevy corvette ZR-1 and already checked fuse what could it be


horn button only grounds it,
put 12 volts to the horn it self see if it works,
if it does then check for horn relay

Apr 15, 2010 | 1990 Chevrolet Corvette

1 Answer

My horn on my 2000 Volkswagen jetta vr6 stopped working and i checked all the fuses and they all good. so i need to find out whats the problem.


Try to locate the horn assembly. When you do, disconnect the wires from the horn and connect them to a volt meter. Make sure that the contacts are free of corrosion. Have a person activate the horn while you check to see if there is a 12 volt supply at the meter. If there is power, clean the contacts on the horn and reconnect the wires to their respective locations. Try the horn again. If the horn does not work, replace the horn assembly. Hope this helps.

Mar 25, 2010 | 1996 Volkswagen Jetta

1 Answer

There is no wirng for me to hook up the actual horn under the front bumper . the horn to the steering is connected cause i can hear it clicking,but the horn under the hood has no wires running to it. nor...


There is only one wire going to the horn & it generally has a connector (12 volt) on the end that slides/clips/connects to or over the terminal you see on the horn.

If you can't see it, you will want to just look up under the frame channel by the radiator, then check the nearest wiring harness locations for the wire you need. When you find a single wire with a terminal that appears that it will plug into the horn, put your test light into the terninal & ground the other end, watch as you press the horn button & you will confirm that this is the wire for that. Also, look for a cut wire where someone may have altered the harness due to a previously stuck horn.

If you can't find one at all, you can wire it yourself from the relay but you should be able to eventually trace the wire by checking all available harness that are nearby & up under the brace.

Good Luck

Feb 08, 2010 | 1994 Honda Civic

1 Answer

Horn not working. Fuse is good. 2005 Jeep Wrangler. How do you remove the rubber cover on the sterring wheel to get at the horn.


May be bad horn. Get a 12 volt test light or multi-meter and attach to the horn wire at the horn. Have a helper press the horn. If you have 12 volts when it is pressed, horn itself is bad. Otherwise, may be bad horn relay. Horn cover should pull off.

Dec 31, 2009 | 2005 Jeep Wrangler

2 Answers

Horn doesn't work


Do you hear a clicking noise in the car when horn is repeatably pressed? If so the horn itself is burned out, if you want to verify the horn problem go to the horn location and with a 12 volt test light (avail at any auto parts store) have someone press and hold the horn on, then probe the horn wire terminals and see if the test light lights.

Jul 28, 2008 | 1995 Oldsmobile Silhouette

Not finding what you are looking for?
2005 Chrysler Town & Country Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...