Question about 2006 Ford Focus

Open Question

My 2006 ford focus ZX4 ST keeps popping a 20A buss fuse under the hood. my car needs this fuse to start the car and to beable to see/read thw odomiter and trip. i need an exploded view diagram of the wiring to isolate the ground thats in my car. if yalls can help i would be VERY appreciative! Thank You! Brenten Bear

Posted by on


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 560 Answers

SOURCE: diagram on how to install ford focus 2006 zx4 serpentine belt?

Autozone or a similar parts retailer will print one for you for free.

Posted on Mar 07, 2010

  • 373 Answers

SOURCE: Ford Focus ST 2006 wiring diagrams & workshop info

can you check with parts department at ford and see if thy can
otherwisw check with autozone

Posted on Jan 31, 2009

  • 1871 Answers

SOURCE: I need the diagrams of

Hello! Here are the diagrams you requested...Guru...Saailer


Posted on Oct 17, 2010

  • 3301 Answers

SOURCE: 2006 Ford Focus ZX4: Front

the plastic clip that holds the door release rod on the latch is either broken, or fallen off, to fix this you need to remove the inner door panel, there will be screws along the door handle puller, and inside the little door cup, also on the inner door handle there's one, if you have mechanical windows there's a clip that holds that handle on, remove it with a small flat head screw driver, ( watch out they tend to fly off ) once the screw is off the door handle, pop it out towards you, and remove the rod and clip attached to it, once all the screws are removed,, take a putty knife, along the bottom of the panel and pop out the clips that hold this in place slide the panel up to get it off the window rail at the top of the panel,, now once inside your going to see a sheet of plastic, peel it back , look inside the holes in the door for a rod thats come off ,, once you locate the outer door handle,, you will see where the clip and rod go on one end or the other,,

Posted on Aug 26, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I got a zx4 2005 ford focus that will not engage when I put it in to gear. What can I do?

broken cable. try operating the gearshift while looking for the operation on the transmission itself. raise hood and observe the transmission.

Apr 16, 2015 | 2005 Ford Focus ZX4

1 Answer

Where is fuse box location for 2005 focus

You can find the owners manual for your 2005 Focus online by googling 2005 Focus Owners manual. On page 127 under Roadside Emergencies it describes the fuse panel under the dash by the brake pedal. There is a second panel, called the Power Distribution Box under the hood in the engine compartment. The manual describes the location of each fuse and relay. Good luck!

Feb 20, 2015 | 2005 Ford Focus ZX4

1 Answer

2006 Ford focus zx4 St..replaces the alternator last night car ran fine all day I came home for lunch and then I went to leave to go back to work about 35 min later and the car would not start wouldn't...

Make sure battery has a full charge. With everything off, use digital multimeter leads across battery posts, the generic spec is around 12.6 volts. Leave the leads hooked up, have helper turn key to crank, what is the reading? If the circuit is closed to the starter, shouldn't drop below 9.6 volts, some makes and models, it shouldn't drop below 10 volts. You get the picture, if drops way low, that won't work.
I'd have to check generator output and battery.

Apr 11, 2017 | Cars & Trucks

1 Answer

Car will not go into gear and brake lights are not working, have to override the gearshift by inserting my key in the small pop off tab , but still do not have brake lights, replaced the Brake switch and...

Fuse 42 should be 15 amps-not 10. If 15 amp fuse still burns, Brake light circuit is drawing too much current, causing the fuse to burn. The problem may be the shift lock solenoid or the lights. See diagram at link below.

Feb 01, 2018 | Ford Cars & Trucks

2 Answers

Where is the fuse for the 12V plug in the dash in my for 2006 ford focus zx4 se

Go to the link below to find your fuses. Page 147 fuse # 47 is for the power point plug

Good Luck please rate 4 thumbs up and please leave a testimonial

Oct 31, 2010 | 2006 Ford Focus

2 Answers

Diagram on how to install ford focus 2006 zx4 serpentine belt?

Autozone or a similar parts retailer will print one for you for free.

Mar 07, 2010 | 2006 Ford Focus

2 Answers

How to install ford focus 2006 zx4 serpentine belt?

what is your question? what dont you know how to do? do you have tools? belt diagram available from parts stores. you have a tensioner, so you need to turn it to release tension. other than that i need more info.

Mar 07, 2010 | 2006 Ford Focus

4 Answers

2001 ford focus ZX3, #10 fuse keeps popping.

a loose or damaged wire is causing a short circuit!
you ned to get it tested & rectified by a auto electrician ASAP!
as wiring gets very hot & can destroy your vehicle! {catch fire]

Jul 20, 2009 | 2000 Ford Focus

1 Answer

The engin control fuse keeps blowing on my 2005

your fuelpump could be causing the fuse to blow as it may be seizing up

Apr 18, 2009 | 2005 Ford Focus

Not finding what you are looking for?
2006 Ford Focus Logo

Related Topics:

808 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides