Question about 2006 Ford F-150

1 Answer

I have a 2002 ford f150 xlt fx4 4.6l engine. 2 door reg cab. i have a 4 wheel drive shift lever. the 4 wheel will only engage on rare occasion and only after pulling into 4 low then to 2 high then back and forth to engage. this will engae even in 4 low approx 5% of the time? what can i do??suggestions??

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 984 Answers

For the 2002 MY ( this is in the 2006 Section, just want to call it out to others that might find the solution, this does not apply to the 2006 MY )

Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
{ picture of shift motor }
-- If the vacuum shift motor does not move:
1.Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
2.Check the fuses for the 4WD system and the solenoids.
3.Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
4.Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
5.Check the vacuum reservoir box for cracks.
6.Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
7.Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
i have a 2002 ford - sscullys_148.jpg

- If the front drive shaft turns:
For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

I am going to take a SWAG that it is 1 of 2 places, both cases the front drive shaft is locking into place.

1. The front vacuum shift motor is not moving ( vacuum or vacuum line issue ).
2. The contact plates for the shift motor are not making contact and are not signalling the GEM that the transfer case state has been changed.

I'd start with the front axle off the ground test, and see which way to go, before you start repalcing items.

Posted on Mar 28, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Got. A 2003 f150 4x4 got problems with 4 wheel drive locking in and stay in drive shaft turning front wheels not


Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).

Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem ( this is what you seem to have, the transfer case is engaged and will drive the front shaft mine was a key on engine off test ).

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
sscullys_185.jpg
-- If the vacuum shift motor does not move:
1.Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
2.Check the fuses for the 4WD system and the solenoids.
3.Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
sscullys_187.jpg
4.Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
5.Check the vacuum reservoir box for cracks.
6.Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
7.Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
sscullys_186.jpg

Usually the case is cracked vacuum lines from the solenoids, the next common is a cracked vacuum reservoir box, and 1 time I have seen the mount for the vacuum disconnect motor broken ( motor floating free so it could not push against the axle )
sscullys_188.jpg

Aug 28, 2011 | 2003 Ford F150 Regular Cab

1 Answer

Ford 4-wheel drive help


This is for 4x4 shifter on the floor.
In the front of the truck on the axle there's a plastic cover with 2 10mm bolts remove it and spray down the shifting actuator it operates on vacuum. You might have to pull it in four wheel and check to see if the vacuum pod is engaging the shift lever on the axle. Then again you might have to replace it very easy to do. But I would spray it down with some WD-40 it should work.

Feb 07, 2010 | 1997 Ford F150 Regular Cab

1 Answer

Ford f150 xlt 4x wont engage


Soledoid at transfer case unpluged or defective on board swith..Check contacts with voltage tester at switch first... power in? power when swtch on? Go to soledoid under veh. at case

Oct 31, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Hi, I can't get my transfer case shifter lever into 4 wheel low. It works easily to high. I've got a 1991 F150 4x4 XLT with auto trans and the 5.4 V8. Thanks Tom


make sure you're doing it correctly. floor shift 4wd's usually need to shove the lever to the right or left to scoot into 4LO. if you have manual hubs, make sure they're in. double check the fluid levels and mechanicals to the front Pumpkin to make sure nothings binding up, too.

Jun 10, 2009 | 1998 Ford F150 Regular Cab

1 Answer

How to shift into 4wd


Ford has 2 types of 4x4 system engagement. One is a knob on the dash that you just turn to 4wheel drive high or low. The other system is the 4x4 transfer case shift on the transmission tunnel (hump) between the driver and passenger seats. To shift into 4 wheel drive high while driving, just let off the gas and shift transfer case into 4H position, and continue driving. To shift into 4 wheel drive Low, stop the vehicle completely, put transmission in neutral, shift transfer case into 4Low position, put trans. in gear, and start driving. I am assuming before doing the above, you have locked in ( turned the front hubs to 4 wheel drive position.) Any further questions, let me know.

May 16, 2009 | 2003 Ford F150 Regular Cab

2 Answers

2004 Ford F-150 extended cab FX4. 4WD problem


The malfunctioning part in my case is what ford calls the "integrated wheel end" which locs the weel hub on the four wheel drive in or out as need. Part is available from Ford and cost about $110.00. I will do this repair myself.

Apr 08, 2009 | 2004 Ford F150

1 Answer

Elec 4 wheel drive light comes on but 4x4 not engaging


change the 2 solenoids on the firewall on the passenger side. they contol the vacum to the acuator.

Jan 27, 2009 | 1999 Ford F150 Regular Cab

1 Answer

98 Ford F150 4x4 wont engage


I copied something that you might use because it was handy I know its not going to be exactly for you but it might get you fixed. Let me know if it helps or NOT please. gl dc

Jan 18, 2009 | 1998 Ford F150 Regular Cab

3 Answers

Ford F150 front tires won't engage in 4 wheel drive


look on fire wall pass. side you will see 2 parts with vacume lines attached 99 percent of the time that is what went i had the same problem

Dec 15, 2008 | 1999 Ford F150 Regular Cab

Not finding what you are looking for?
2006 Ford F-150 Logo

827 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...