Question about 1998 Chrysler Concorde

1 Answer

Engine Issues When replacing a engine in a 1998 Concorde, do you have to replace the input and output sensors

Posted by on

1 Answer

Car starts and runs good but it shotsdown when its running

Posted on Aug 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Po715 automatic transmission most of the time it don't want to go to the other gears stays in first gear


This is cause by three things. 1. Low fluid causing difficult shifting. 2. Bad electronics in the 1,2, shift circuit. Or the transmission is in limp mode. The transmission can go into limp mode for several reasons. Try removing the gas cap, sometimes the evap system will cause issues. Also get the car to normal operating temperature and check the trans fluid, add as necessary, do not overfill.

Feb 21, 2015 | Cars & Trucks

1 Answer

How can I reset anew output speed sensor on a 2001 hyundai xg300


There is nothing do do to reset it. After you change it you're done. If you're talking about your check engine light being on, you can reset it with a scan tool. If you don't have access to one, disconnect the battery and wait a couple minutes before connecting it back. If you're having actual mechanical issues after you've installed the output sensor you might need to replace the input sensor also.

Jul 13, 2014 | 2004 Chevrolet Suburban

2 Answers

My speedometer stopped working, the check engine light came on and the transmission won't shift out of low. 1998 Concorde LXI


You will need a speed sensor it at the tail of thhe transmission the very last one is speed output sensor or vss (vehicle speed sensor) NOT input sensor

Aug 21, 2011 | 1998 Chrysler Concorde

1 Answer

Check engine code po731 1998 dodge caravan


this is an obd2 trouble code table, it can help you understand the meaning of code, and
you need Replace the input and output speend sensor on the transmission to take care
of this problem, parts are about 60 bucks at the dealer.

Jul 06, 2011 | 1998 Dodge Caravan

1 Answer

2001 CONCORDE TRANSMTSSION WILL NOT CHANGE GEARS 3rpms going to the limit 4 engine growl instead of shifting


you need to have three sensors checked on the transmission,output sensor,input sensor,and speed sensor,
one is not telling the computer your speed,so the computer keeps you in limp mode

Jan 20, 2010 | 2001 Chrysler Concorde

1 Answer

When you stop transmission hangs in 2nd gear. you can put it in park and shut engine off then start engine and transmission will shift.


transmission going into limp mode,
check speed sensor, and input sensor and output sensors will fix it

Nov 24, 2009 | 1998 Plymouth Breeze

2 Answers

1998 chyrsler concorde stays in first gear??? What is it I need to purchase to repair it


If there is a Transmission shop close to you, have them scan the car for the DTC codes that would indicate what issues your transmission has. Check the fuse box for any bad fuses like the transmission fuse if it labeled and the wire harness from the transmission control module, (TCM). If your speedometer is not working, then it's your Vehicle Velocity Sensor (V V S) that need to be replaced and it's around $28.00 at the dealer and takes about 15 min to replaced. Take your time running the car so you don't burn out the transmission and engine running on 1 st gear. Which i believe is 2nd as it's in limp default. Good luck

Nov 11, 2009 | 1998 Chrysler Concorde

1 Answer

Check engine light with following codes p 1529 p0720 p0715


P1529 indicates that your TCM asked the ECM to turn on the check engine lamp.

The range switch and the output speed sensors are the items that are abnormally affecting the operation of the transmission. The diagnostic logic in your computer can distinguish these issues from one another, so you'll definitely want to do both. You have no diagnostic code for the input speed sensor (P0715) listed, so I have made no recommendation to replace it. In my opinion, it's not a labor-intensive repair, so I wouldn't recommend replacing it unless you have reason to believe it's bad.

DTC - P0720 (OUTPUT SHAFT SPEED SENSOR SYSTEM)
Code No. P0720 Output shaft speed sensor system
If the output from the output shaft speed sensor is continuously 50% lower than the vehicle speed for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h or more, it is judged to be an open circuit or short-circuit in the output shaft speed sensor and diagnostic trouble code No. P0720 is output. If diagnostic trouble code No. P0720 is output four times, the transmission is locked into 3rd gear or 2rid gear as a fail-safe measure.
Probable cause
Malfunction of the output shaft speed sensor
Malfunction of the transfer drive gear or driven gear
Malfunction of connector
Malfunction of the TCM

DTC - P0715 (INPUT SHAFT SPEED SENSOR SYSTEM)
Code No. P0715 input shaft speed sensor system
If no output pulse is detected from the input shaft speed sensor for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h (19 mph) or more, it is judged to be an open circuit or short-circuit in the input shaft speed sensor and diagnostic trouble code No. P0715 is output. If diagnostic trouble code P0715 is output four times, the transaxle is locked into 3rd gear or 2nd gear as a fail-safe measure.
Probable cause
Malfunction of the input shaft speed sensor
Malfunction of the underdrive clutch retainer
Malfunction of connector
Malfunction of the TCM

Is needed replace.

Nov 04, 2009 | 2001 Hyundai Elantra

2 Answers

1999 concorde. in limp mode with check engine


you should also replace the input speed sensor,they should always be done in pairs and i have had both of them bad on numerous vehicles,hope this helps

Sep 09, 2009 | 1999 Chrysler Concorde

Not finding what you are looking for?
1998 Chrysler Concorde Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...