Question about Dodge Stratus

1 Answer

My car is showing PO344 (Camshaft Position Sensor A Circuit Intermittent) as a problem it's having... I replaced the camshaft sensor about 2 years ago when I was having a similar problem; could the sensor have gone out, or would this be a different problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 17,970 Answers

All ways, the camshaft position sensor signal sent to the ECM is intermittent

The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Powertrain Control Module (PCM) or Electronic Control Module(ECM) to control ignition and fuel injection. The camshaft position sensor senses the retraction of camshaft (intake) to identify a particular cylinder. The camshaft position sensor senses the piston position. The sensor system consists of a rotating part, typically a disc, as well as a static part, the actual sensor.

When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.

When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals.

Check thos DTC diagnostic and possible solutions about P0344 - Camshaft Position Sensor Circuit Intermittent

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall

Possible causes
- Harness or connectors (The sensor circuit is open or shorted)
- Camshaft position sensor may be faulty
- Camshaft (Intake) may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead (Weak) battery

Possible solution
- Charge battery
- Repair harness or connector
- Replaced Camshaft Position Sensor.
Tech notes
- Sometimes and in some models, low battery voltage or a weak starter can can trigger a Camshaft Position Sensor code.


Hope this helps.

Posted on Mar 27, 2011

  • ptac23025sd Jul 28, 2011

    thank you very much the problm whith my 2004 911 with code po344 was infact a weak battery causing slow cranking setting code po344

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a PT 2010 & the diagnostic codes are PO340, PO344 and PO325. mechanic is suggesting replacing the cam shaft post sensor & didn't even mention the knock sensor. Am I dealing with 1 or 2 issues


you are dealing with 2 issues
code p 0325 refers to knock sensor (KS) 1 bank 1--circuit malfunction ====causes ---wiring ---poor connection ---KS
code p 0340 refers to camshaft position sensor(CMP) sensor A bank 1--circuit malfunction===causes wiring--- CMP sensor ---ECM
code p 0344 refers to CMP sensor A bank 1 --circuit intermittent===causes --wiring --poor connection---CMP sensor --ECM
check wiring and connections before replacing the CMP as the wiring may be the cause of all the codes

Oct 21, 2016 | 2010 Chrysler PT Cruiser

1 Answer

P0016 what is that n how u fix it


P0016 Crankshaft Position - Camshaft Position Correlation
P0135 O2 Sensor Heater Circuit
P0138 O2 Sensor Circuit High Voltage
P0340 Camshaft Position Sensor "A" Circuit
P0344 Camshaft Position Sensor "A" Circuit Intermittent
P0508 Idle Air Control System Circuit Low
P0522 Engine Oil Pressure Sensor/Switch Low Voltage
_____________--
JMA TRS-5000 Cloning Machine

Jun 03, 2013 | Cars & Trucks

1 Answer

Mustang error codes P0340 , P0344


These are camshaft position sensor codes. Replace camshaft sensor.

Apr 18, 2017 | 2006 Ford Mustang GT

1 Answer

Runs but wont go over 2300 rpms showing code number P0344


Installing parts based on a code is not how it is done

The codes do not tell you what is wrong or what to replace

PO344-Camshaft Position Sensor Circuit Intermittent

The sensor just reported a fault code,now you need a shop
with trouble charts to properly diagnose the issue

Could be mechanical

Nov 30, 2012 | 2005 Dodge Neon SXT

1 Answer

What does PO344 mean


Code PO344: Rationality error detected for intermittent loss of camshaft position sensor circuit

A problem with either your cam/camshaft sensor.

Apr 30, 2012 | 2006 Dodge Durango

1 Answer

Whats the position of the crankshaft position sensor on 2005 pt cruiser non turbo


P0344 CHRYSLER - Camshaft Position Sensor Intermittent Interruption Bank 1 Sensor 1
Possible causes - Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit

Dec 14, 2011 | 2005 Chrysler PT Cruiser

2 Answers

05 kia amanti with diagnostics codes p0350,p0320,p0300,p0302,p0303,p0304,p0305,p0306.skipping at times.when it does skip & misfire the rpm gauge goes crazy.this problem is not consitant


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Nov 17, 2010 | Kia Amanti Cars & Trucks

1 Answer

Have2004 intrepid shows engine light and error codes po340-& po344


code po 340 no camshaft position sensor signal at powertrain control module and code po344 rationality error detected for intermittent loss of camshaft position sensor circuit. hope this will help you!!!!

Apr 18, 2010 | 2004 Dodge Intrepid

1 Answer

Code po344 on 1996 ford f250 powerstroke


camshaft position sensor circuit intermittent check sensor connectionsand follow wire back make sure not to close to spark plug wires(causes interference)

Oct 23, 2009 | 1996 Ford F250 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

2,062 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...