Question about 1998 Plymouth Breeze

1 Answer

My car won't start after replacing the engine when told it was timing problems and easier to replace the whole thing rather than tinker with it, and a new fuel pump when there was no fuel being sent through the lines. It's still not getting fuel or spark but it seems there is a wiring problem under the fuse box, how do we get it out to figure out where the problem is? And does this seem logical?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 67 Answers

I wonder if maybe some wiring got pinched when replacing the engine, that is completely illogical that you have no fuel or spark. Thats what I would do is start checking for power and ground at fuel pump and spark sources like the crank sensor. That would be the only thing that makes sense to me.

Posted on Mar 27, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starts but won t keep running


Probably not. Once the oil passages inside the engine get plugged up the block has to be hot-tanked to get them cleaned out. Thats after the engine is disassembled.
You can try an engine flush or two, but I would not expect much.
You may not be getting power to the fuel pump if oil pressure is low.

Jul 14, 2013 | Chrysler 300M Cars & Trucks

1 Answer

98 Isuzu rodeo, engine cranks and trys to start but it won't


If this is a diesel engine you probably have an air lock in the fuel system. It will need "bleeding" before it will start. If you have already tried bleeding the fuel system there may be an air lock in the injectors. If it still doesn't start I suggest you carry out a compression check because diesel engines need to be in good condition to start easily, especially in cold weather If it is a petrol engine, there could be problems with engine timing or ignition problems.

Oct 25, 2017 | Isuzu Rodeo Cars & Trucks

1 Answer

2006 dodge stratus won't crank and cruise control won't light


Must not have been much of a mechanic. If the engine runs and sounds fine sometimes and other times it doesn't then it does not sound like a mechanical problem with the engine. Sounds more like a issue with either the ignition system or fuel system.

Feb 20, 2018 | 2006 Dodge Stratus

1 Answer

Hi. i have a 1986 mazda 626, with the 2.0 4 cyl engine. car sat for a year or two. i replaced the driver side c.v., and the clutch. after some tinkering i got the car to start. but, for some reason it...


If the cars stays running for this amount of time I would replace the fuel filter to start. If it continued after this , check the fuel pressure and replace the pump if necessary. The only other thing I would be concerned about is the security system. But these usually only let the car run for about 2 to 3 seconds before shut down.

Jul 29, 2011 | Mazda 626 Cars & Trucks

1 Answer

Trans shifts into overdrive at to low a speed. Then has a real hard time downshifting. The fluid is full and its red not burnt. I don't notice any slippage either. But when you try to accelerate it...


Sounds to me that your transmission is starting to wear out. The only thing you can do is replace the whole thing if it's an automatic. Standard transmissions are a bit easier since all you'd have to do is replace a single gear. Also, it helps if you replace the fluid and filter which involves dropping the pan since the filter is located inside the transmission oil pan.

Jun 10, 2011 | 1995 Oldsmobile Cutlass Ciera

1 Answer

I need to replace the transmission mount on a '94 1500 4.3L, 4X4. Which is easier, support the transmission and remove the cross member or release the engine mount bolts and raise the drive train? Tks


Supporting the transmission while removing the cross-member is easier. You will have the engine mount holding the whole thing in precise place, while you deal with the crossmember, and the transmission.

Comparing: if you release the engine mount bolts and jack up the drive-train, the whole thing would shift, and you could have trouble when the cross-member fails to go up well enough.

On the other hand, if the cross-member bolts fail to release due to "home-mechanic" syndrome, you have only the first option.

Dec 03, 2009 | 1994 GMC Sierra

1 Answer

I have a similiar problem to [mountean on Nov 14,2009] except I replaced the whole distributor ,now I'm getting spark , but it won't start,catch,or even try to start.Somebody told me the timing belt could...


the first thing you need to check is the timing i have this same exact car the timing does have a tendency to jump re time it if itstill wont start after the timing is fixed check that the distributor the rotor should be at the number one plug when number one cylider is at top dead center

Nov 20, 2009 | 1995 Honda Civic

1 Answer

Power Issue?


check your throtle possiton sensor. it controls the amount of gas given to the engine when you push the pedal. i had the same problem. its located right behind the throtle body and connected by 2 screws. its adjustable so tinker with it and if it needs replaced its about 100 bucks

May 27, 2009 | 1990 Toyota 4Runner

2 Answers

REplaced fuelpump , but it won`t start . I hear the fuel pump run and I was told the inline filter was replaced. So what is rong ?


Do you have a "no start" based on fuel, ignition, or engine problems? All of these are required to be good to start an engine. Must check for spark at plugs. If o/k check fuel pressure at fuel rail.If o/k check engine copression.

May 05, 2009 | 1993 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1998 Plymouth Breeze Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...