Question about 2004 Isuzu Rodeo

Open Question

How do I remove an ignition barrel from a 2006 Ra Isuzu Rodeo? Have purchased a new barrel and don't know how to get the old one out?

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 135 Answers


it is better to buy a new ignition takes a special socket to get the screws out, once the screws are out they do not need to be new barrel,disconnect negative battery cable,disconnect wires from barrel assembly, remove barrel from colum. first take vin# to dealership parts department to get correct barrel assembly, the keys with new assembly will fit doors and trunk

Posted on May 20, 2009

  • 9 Answers

SOURCE: 2000 isuzu rodeo removal and installation of serpentine belt

All u need to do is put a wrench on the tention pully and turn it clockwise... this will relive the tention take off the old belt ....put on new one. repeat relive pressure again ...slip it on pully... and relese tention..... done! :)

Posted on Jun 11, 2009

  • 4 Answers

SOURCE: mercedez 190 ignition barrel. I have taken out ignition barrel attached to steering coloum but i can not remove key ignition from steering coloum how does it remove ignition barrel from steering

Should be the same as w123 model. Check diy Mercedes web page.
Photos included easy to do.

Posted on Jul 07, 2009

  • 407 Answers

SOURCE: my 96 Isuzu rodeo won't start and key is stuck in ignition

either that or the ignition switch itself is binding up

Posted on Oct 27, 2009

Testimonial: "Thank you very much. That should do the trick"

  • 1757 Answers

SOURCE: I need to find a diagram for a timing belt for a 1995 Isuzu Rodeo

We are talking about the Timing Belt and not the Drive/Surpentine Belt?

For the Timing Belt: CLICK on the following Link. It has all the Diagrams you will need for the Timing Belt.

For the Drive/Surpentine Belt: CLICK on the following Link. It has all the Diagrams you will need for the Drive/Surpentine Belt.

Let me know if this helped, or if you have additional information or questions. Feel free to contact me at!

Posted on Feb 27, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove injector pump on a 2006 isuzu rodeo ra

name the engine tell size. and country.
this is usa forum;. so can't guess any of that.
rodeo ended state -side (USA) in 2004
"Production of both SUVs concluded in 2004."
so my wild guess you are like down under, in Australia or NZ?
and is really a HOLDEN? (1/2 baked)
or you posted wrong year, or car is a Dmax
or I-280 or Asunder, or??? well gee, I cant guess...

May 24, 2016 | Isuzu Rodeo Cars & Trucks

1 Answer

Key comes out but won't turn the car off

the ignition barrel/key are so worn they are'nt engaging properly when turning off put a slight downwards pressure as turning key this may engage the key and barrel but sounds like need a new key if thats worn smooth or a new barrel if key is sharp

Apr 22, 2014 | 2000 Isuzu Rodeo

1 Answer

98 isuzu rodeo ac button does not lite

If the AC works, it is probably just a little light bulb behind the button. You can either learn to live with it or find a spare part on eBay. Many times by ordering the new part you can see how to remove the old one. Don't simply try to pry it out, you may need to remove the panel first then pop out the old button from the back.

Nov 14, 2012 | 1998 Isuzu Rodeo

1 Answer

I have an Isuzu Rodeo and the key is stuck in the ignition any idea how to get it out? Year 2000

replace the whole ignition barrel with new key and get key programmed by dealer
can remove barrel and key by removing steering column covers turn ignition to on position and with small shank screw driver push in hole in outer top rear section of barrel assembly then pull out ignition lock barrel with key in it. fit new lock barrel and key, program new key into system and can get door lock barrels coded to suit new key or get code for old key and cut new key so it fits mechanical locks on the rest of the vehicle (just wont turn in ignition) 2 keys for vehicle.

Jun 13, 2010 | 2000 Isuzu Rodeo

1 Answer

How to install key ignition

their is a small button to press in on the side of the switch which holds it in the barrel. Press it in with a small screw driver but the button will only press in when the key is in the ignition. Just hold it in while pulling out the old switch from the barrel same procedure to replace.

Sep 09, 2009 | 1993 Isuzu Rodeo

2 Answers

I lost my keys for my 2003 rodeo

you will have to get a dealer to cut new keys to code that dealers have access to and then get them to program to car but also erase old keys so vehicle wont start with old keys
or next more expensive option is new keys, ignition barrel and door barrels replaced which are differently same coded key and locks as well as programming and erasing old keys.

Jun 27, 2009 | 2003 Isuzu Rodeo

Not finding what you are looking for?
2004 Isuzu Rodeo Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14411 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides